This seems to happen in many different drivers but it happened more often in newer versions such as 530 vs 525.
Then nvidia-modeset goes to 100%
There are many reports of this appearing since driver 4.70 and I can confirm I've seen this in various machines.
https://forums.de........
Nov 15 17:00:49 rttbox kernel: overlayfs: filesystem on '/var/lib/docker/overlay2/check-overlayfs-support450709549/upper' not supported as upperdir
Nov 15 17:00:49 rttbox dockerd[93755]: failed to start daemon: error initializing graphdriver: driver not supported
The above error is often/normally caused because you are trying to run docker out of an unsuitable directory/filesystem. For example if you try to place docker's data inside an existing overl........
find /usr/share/zoneinfo/|sed s#"/usr/share/zoneinfo/"##g|grep "/"|grep -v posix|grep -v ^"Etc/"|grep -v ^right|grep -v ^"SystemV"
Africa/Addis_Ababa
Africa/Abidjan
Africa/Blantyre
Africa/Lusaka
Africa/Casablanca
Africa/Libreville
Africa/Asmara
Africa/Bujumbura
Africa/Dakar
Africa/Lagos
Africa/Malabo
Africa/Harare
Africa/Kigali........
request_module: runaway loop modprobe binfmt-464c Kernel panic - not syncing: No init found Pid: 1, comm: swapper/0 Not tainted
This is usually caused by a mismatch in architecture and happens frequently in development environments.
Here is a example of what caused this issue:
Your binaries are based on one architecture
Your kernel was compiled with another architecture.
Why does this happe........
It is a bit different and annoying here for these types of routers/models as you need to physically remove the CF (Compact Flash) and only then, will it enter ROMMON mode (Ctrl + Pause remotely over the console will not do it for us). This means you cannot do this remotely, or at least not without the help of a remote/physical helper.
Step 1.) Power off, router and remove CF Disk Slot#2
Go to the router and remove the slot#2 cover uses your hand or it may help to use a........
It may appear to be an Xorg or lightdm/gdm/mdm error but in reality for many users with this issue, it's a driver conflict and issue. I had a system that had two GPUs, an Intel and Nvidia GPU.
The only thing that got it working was to remove the nouveau driver and blacklist it so it never came back, then the Intel GPU works fine without these issues.
Solution
sudo rmmod nouveau
add nouveau/other driver to blacklist
edit th........
Here is how Ifixed it on a Mint/Ubuntu install
1.) First download the latest AMDGPU-Pro driver from here:
https://www.amd.com/en/support
Navigate to your relevant video card:
2.) Download the installer
One issue is that by default they give you a version for the latest version of........
You just add on "non-free" at the end of each repo, like the example below:
If you wanted contributed packages then you could also add "non-free contrib" to each repo line.
Don't forget to do an "apt update" to see the new packages, this is especially handy for getting more drivers for devices with the firmware-linux-nonfr........
If you get an error like this when installing the Nvidia drivers:
WARNING: Unable to determine the path to install the libglvnd EGL vendor library config files. Check that you have pkg-config and the libglvnd development libraries installed, or specify a path with --glvnd-egl-config-path.
Just install these packages: &nbs........
Linux Mint offers an easy and painless upgrade path through the last 3 versions, which means no more reinstalling to stay current with the latest version.
The only catch is that you need the latest of each version, so for 18, you need 18.3 before you can go to 19, and then 19.3 (or latest), until you go to 20. However, it's really a small price to pay and on the machines we've tested, the upgrade went seamlessly each time (although sometimes video drivers/custom kernel modules l........
Bonding is an excellent way to get both increased redundancy and throughput. It is similar to the "Network Teaming" feature in Windows.
There are a few different modes but we will use mode 6, I think it's the best of both worlds, as it is not just a failover, but it provides round robin, so you will get redundancy and load balancing. So if you have a 1G single port, you will have a combined throughput of 4G at this point. Just bear in mind that the true thr........
You might assume you have a bad drive or the SATA interface/cable is bad, or the power supply is bad/weak to the drive. These are all possible issues, but definitely check your SATA cable for "twisting". It is a big issue because until the error stops or times out, your system will not boot (in my case this was the case even though the drive with the issue was not part of the OS or booting process at all).
If you run an open rig that you move around often that ha........
For a lot of reasons, it may be convenient to detach or attach live disks to a running VM without having to reboot it. Sure, you can use some network based storage, but when performance counts, attaching a new virtual disk will usually give you better throughput and lower latency in a quick testing situation.
This doesn't work, why not?
drive_add 0 if=virtio,file=/tmp/vm.qcow2,if=virtio,format=qcow2,id=rtt
Can't hot-ad........
Many people may not be aware that you can turn commodity hardware into a Mikrotik OS and there are various options which is "CHR" (Cloud Hosted Router) which is a VMimage meant for Virtualization only (seriously, I've tried to dd the image to a physical server and it just crashed as it does not contain any drivers for physical).
One note as well if you are trying to do a baremetal install you may get an error "Error Loading Operating System" or........
It took a lot of fiddling to make a Huion Kamvas 13 Pro work in Linux but it simple once you know what to do. Don't bother searching as it is unlkely there is a guide out there that will actually make your tablet work.
It mainly comes down to the fact that the hid_uclogic kernel module is buggy or doesn't support MANYof these wacom based/Huion tablets properly.
What was happening with me is that Ihad the Kamvas 13 Huion setup as a secondary screen/monitor.&nb........
It really seems limited in that it can mainly give you the things you would see on the physical unit such as load etc..
wget https://downloads.sourceforge.net/project/apcupsd/apcupsd%20-%20Stable/3.14.14/apcupsd-3.14.14.tar.gz?r=https%3A%2F%2Fsourceforge.net%2Fprojects%2Fapcupsd%2Ffiles%2Flatest%2Fdownload&ts=1598115866
tar -zxvf apcupsd-3.14.14.tar.gz
cd apcupsd-3.14.14
[root@somebox apcupsd-3.14.14]#
./conf........
If you've come here, don't be embarraassed, working in IT, this is the MOST common computer problem that almost everyone will encounter. The reason why I'm doing this post is because I've seen an increase from colleagues and admins having this problem and many times it's not even your fault. A common scenario is that someone acquires a new or used computer which they weren't given the password for. Fortunately Ihave a detailed list of all the options whether free or pa........
This seems to happen on most if not all Nvidia cards but the good news is that if you are using any of the Linux drivers and have the nvidia-settings tool installed it is just a simple command.
Solution:
nvidia-settings --assign CurrentMetaMode="nvidia-auto-select +0+0 { ForceFullCompositionPipeline = On }"
Enter the above command in your terminal and the screentearing will be fixed which is like enabling Tear Free on AMD cards.&........
I was using a small box as a router and one of the ports started going off and coming back at 100M. I truly believe it is simply that it was a case of overheating. Although CPUtemps were only about 67 degrees, the physical box itself was almost burning hot. Isolved the cooling issue and never had the issue again.
Jul 28 15:09:27 swithbox kernel: e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx
Jul 28 15:09:28 swithbox kernel:........
It's as simple as below where you just specify the dev device of the CDROM which is usually /dev/sr0. You can boot actual bootable discs like Windows, Linux, etc straight from a physical drive this way.
sudo qemu-system-x86_64 -cdrom /dev/sr0 -m 4096
........
This is the reason that I don't like the new ADATA USB drives such as the UV128/64GB or 128GB drives and other ones that look to be the same style (the green sliding USB connector).
They just don't work well from new and never work properly at any point.
[ 788.242463] usb 1-1.2: new high-speed USB device number 16 using ehci-pci
[ 788.339816] usb 1-1.2: New USB device found, idVendor=125f, idProduct=db8a
[ 7........
A lot of times this is actually caused by simply not having Firefox installed at all.
selenium.common.exceptions.WebDriverException: Message: Can not connect to the Service geckodriver
https://github.com/mozilla/geckodriver/issues/270........
I find that the default settings for the radeon driver that is applied to most AMD cards is horrible. For example by default TearFree is not enabled and it causes videos to have some kind of square artifacts.
Here are the settings I have found most suitable for AMD cards:
You need to create file in the following path and restart Xorg or your computer to apply it:
*Beware that making a mistake here will possibly make your computer........
I don't consider a lot of these "extra" kernel modules "nice to have" as they often contain drivers for essential items like your soundcard, your NIC and many other devices that may not work. Sometimes you may find that "sound" or "ethernet" worked before a kernel/OS upgrade and now in the new version they don't. Often it will be because you need to install the "extra" kernel modules.
One other weird thing is that sometimes........
Install Errors on Version 12:
This error happened on QEMU emulator version 2.11.1 pve-qemu-kvm_2.11.1-5
on Proxmox/Debian but installing on QEMU.12 on Centos 6 did not produce the error.
*Update it is not related to the OS or QEMU version. This happened in Centos 6 too after a second install.
What really causes this even though you successfully install........
Oops did you get this error trying to install an oldschool driver and think it is hopeless in a new version of Windows?
First of all it is almost never a program compatibility issue:
........
The key thing here is to know the actual partition that is encrypted.
Often in Linux Mint's installer that ends up being partition 5 or /dev/sda5
sudo cryptsetup luksOpen /dev/sda5 anynamehere
You will then be prompted for your irrecoverable passphrase:
Enter passphrase for /dev/sda5:
If all goes well it won't say anything further. If it says ""No key available with this passphr........
Before getting into the output here is my typical experience with SMART, there is what I call a "bad disk" with pending and uncorrectable sectors that cannot be reallocated.
It has caused a kernel panic and system crash repeatedly as we can see from the logs.
But SMART says it has "PASSED" its self assessment. SMART is still useful to me but it is more about looking at Current_Pending_Sector.
Any time I have had anything but 0 for that attribute it........
dvd+rw-mediainfo /dev/sr0
INQUIRY: [ASUS ][BW-16D1HT ][3.00]
GET [CURRENT] CONFIGURATION:
Mounted Media: 11h, DVD-R Sequential
Media ID: RITEKF1&n........
You can search for this bug and it seems like it may be related to ecryptfs and is many years old.
The symptoms are that you return to the computer and the screensaver was active or the screen was asleep/black and it doesn't seem to come back. But you check by SSH the computer is running fine and are frustrated you'll lose your running programs and have to reboot.
There is a simple solution:
Ctrl + Alt + F1
Ctrl +Alt + F8
Ba........
In xplayer Iget the following error "Could not initialize supporting library.". It actually looks more like a gstreamer issue.
For those wondering what the default video player is called it is "xvid" and not "totem" anymore like previous versions.
Basically it looks like some codecs are missing when I uninstalled another program it uninstalled other programs and codecs that it shouldn't have.
I've tried installing all the gstre........
This works for almost all ISO's Ifind (at least Linux based):
sudo dd if=CentOS-6.9-x86_64-minimal.iso of=/dev/sdg bs=20M
20+1 records in
20+1 records out
427819008 bytes (428 MB) copied, 118.233 s, 3.6 MB/s
Of course change the .iso filename above and the /dev/sdg to your desired USB drive!........
The easiest way is to use SSHand DD or a combination of netcat. SSHwill be a little slower due to encryption but is the most secure way (on two older systems the average clone speed is about 40-50MB/s). This is also OS independent as it doesn't matter what the source OS is because you are literallly cloning the drive so you retain the partition table and settings.
Clone HDD using SSH and DD........
pcimodules no longer works it produces nothing probably because the format of /sys/bus/pci is different.
lspci -k doesn't work on older lspci versions.
pciutils can be compiled but it won't work if you have an old system and compile on a newer glibc.
iteriate through /sys/bus/pci/devices/*/modalias
cat /sys/bus/pci/devices/*/modalias
pci:v00008086d00001237sv00000000sd00000000bc06sc00i00
pci:v00008086d00007000sv0000000........
Done on Centos 7.3 very important as clearly based on older guides it was a lot easier and more simpler! Hint do not use grub2-install!
If you have trouble booting after this check this CentOS mdadm RAID booting/fixing guide.
One huge caveat if you are an oldschool user or sysadmin who has avoided UEFIbooting
The nor........
Why won't my Linux Mint boot after I manually installed a new kernel?
eg.
apt-get install linux-image-newerone
Do this
dpkg -l|grep linux-image|grep extra
ii linux-image-extra-3.16.0-38-generic 3.16.0-38.52~14.04.1&nb........
Here is a simple MP3 player and now there's a reason to understand why the supplied cable has some kind of capacitor and is very short. These devices can be VERY finicky and any voltage fluctuation or difference is enough to cause issues.
Take for example the error messages from Linux Mint:
[804829.895414] usb 1-1: USB disconnect, device number 11
[806961.109030] usb 1-1: new high-speed USB device number 12 using xhci_hcd........
These errors believe it or not are simply because of not being the root user or running with sudo! However if you didn't know to try as root you'd think there was a problem with your burner or disc Essentially it looks like without root you cannot send the required scsi commands to continue writing. Ithink cdrecord should have built-in tests or safeguards to see if it has the permissions to run the required commands.
I guess for more advanced users the idea is simila........
Normally the below would indicate a failing or failed drive. In this case the SATA port was unplugged and sometimes the Linux kernel/motherboard even with AHCIjust don't play nice and can't handle it.
What happened is Iplugged in a new drive after removing another one. However the log shows that after the old drive was plugged in the Linux kernel kept complaining thinking the drive was there but not responding properly. This continued even with reseating........
I've had this issue since Ubuntu 9 and now even on Linux Mint 17 no matter what latest version of the Nvidia proprietary driver that I use. It just becomes slower and slower and only gets better after rebooting or restarting Xorg.
Someone here has it as well
https://askubuntu.com/questions/822449/graphics-becomes-slow-after-a-while/917886
It's very fru........
In short the two drives in the array were /dev/sdd and /dev/sde. The kernel sees they were unplugged and have gone down as you can see below.
mdadm caught the first one being unplugged /dev/sde and disabled the missing drive. However when the final drive that was part of the array is unplugged it didn't notice at all. Instead it complains about an IO error later for drives that the kernel knows do not exist anymore.
[45817.162728] ata4: exception........
This was a surprising bug but I unplugged all drives for an array md127. At first it was just 1 drive and mdadm seemed to notice this. I unplugged the second drive taking the array offline but mdadm did not realize it was offline and still showed a non-existent disk as being part of it. This created problems trying to unmount it or even to stop this array with mdadm freezing.
As for how to fix it I can only think of making sure you are not in a mounted path of........
At first my BIOS said the card may not work right because there is no more option ROM space.
I disabled the Option ROM for both LSI 1068 and 2008 chipsets, Network Boot ROM and most other PCI slots, Serial Port, etc... and the message went away but the card still does not work properly.
But it still cannot initialize the card properly(does not work):
[ 33.943272] NVRM: This PCI I/O region assigned to your NVIDIA device is invalid:........
mdadm --create /dev/md1 --level 10 --raid-devices=2 /dev/sdb2 /dev/sdc2 --layout=f2 --metadata=0.90
Note that layout=f2 or layout=n2 is very important as without it you'll get a complaint like this:
mdadm --create /dev/md0 --level 10 --raid-devices /dev/sdb1 /dev/sdc1 missing missing
mdadm: invalid number of raid devices: /dev/sdb1
It is basically more like a prop........
This is useful if you are installing Windows and need virtio but of course Windows needs the virtio driver which is on a second iso.
This is the line of code you would add to your kvm startup script and then you get this iso as second cdrom you can browse to for your Windows install of virtio driver's or whatever other use you need it for.
-drive file=/kvmtemplates/virtio-win-0.1-94.iso,media=cdrom........
[ 17.208336] tg3 0000:08:00.0: eth0: Link is up at 1000 Mbps, full duplex
[ 17.210194] tg3 0000:08:00.0: eth0: Flow control is on for TX and on for RX
[ 76.000065] phy0 -> rt2x00lib_request_firmware: Error - Failed to request Firmware.
[ 76.002332] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 86.736004] eth0: no IPv6 routers present
[ 148.960038] phy0 -> rt2x00lib_request_fi........
http://realtechtalk.com/downloads/virtio-win-0.1-74.iso
Current Direct stable URL from Fedora: https://fedoraproject.org/wiki/Windows_Virtio_Drivers
Direct Downoad of Stable Virtio: https://fedorap........
./configure
./configure: line 91: cd: /lib/modules/2.6.32-042stab084.25/build: No such file or directory
Error: kernel version not found.
Please make sure your kernel is configured.
dr-xr-xr-x. 4 root root 4096 Feb 21 06:13 ..
lrwxrwxrwx 1 root root 45 Feb 21 06:13 build -> ../../../usr/src/kernels/2.6.32-042stab084.25
drwxr-xr-x 2 root root 4096 Feb 12 20........
Iused the slightly older "304.117" version and it worked.
With the newest version Icouldn't get X to start and kept getting these errors in messages/dmesg.
[ 2346.083660] nvidia 0000:01:00.0: irq 44 for MSI/MSI-X
[ 2350.608342] NVRM: RmInitAdapter failed! (0x12:0x2b:1831)
[ 2350.608354] NVRM: rm_init_adapter failed for device bearing minor number 0
[ 2350.608369] NVRM: nvidia_frontend_open: minor 0, module->open() failed, err........
[3805108.257042] sd 0:0:0:0: [sda] 1953525168 512-byte hardware sectors: (1.00 TB/931 GiB)
[3805108.257052] sd 0:0:0:0: [sda] Write Protect is off
[3805108.257054] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[3805108.257066] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[3805108.257083] sd 0:0:0:0: [sda] 1953525168 512-byte hardware sectors: (1.00 TB/931 GiB)
[3805108.257090] sd 0:0:0:0: [sda] Write Protect is off........
VBox/Virtualbox solution to NS_ERROR_CALL_FAILED error
This is likely because you have 2D/3D acceleration enabled and your card doesn't support it.
Eg. you switched video card drivers or video cards that did support it.
The funny thing is that you CANNOT disable those options as they are "greyed" out in the VBox client GUI.
The config file has to be manually changed and fixed with these options "accelerate3D="false" accelera........
This is a great way to upgrade your RAID array or move it/copy it to a new set of hard drives.
Eg. you have a current RAID 1 array on older/slower drives.
Just add at least 1 of the new drives to the array, update grub/install it and then boot into it. Then you have a transparent data migration that is fully synchronized.
mdadm --grow /dev/md126 --raid-devices 3
md127 : active raid1 sdc1........
One thing to remember is that you need MegaCli to do the flashing.
You also need the correct file,I tried at least 2 different Perc 6 firmwares from Dell that kept getting rejected as corrupt by MegaCli(they were really the wrong version). I have an external PCI-E Dell 6 Perc/I butI chose images from the 'Integrated" on motherboard version as it was allI could find. They are different, and below is my first time finding success.........
LSi Megaraid
At first it was configured as a RAID 0, then I deleted the Virtual Disk Group.
I thought both drives would be shown and detected in Linux as sda and sdb but it actually shows nothing.
To make them work you have to hit Ctrl+R before the system boots (when prompted) and create a Virtual Disk Group. In my case I created each one as RAID 0 (with a single drive only) as I just wanted JBOD but there is no such option or default in these Dell Pe........
package kernel-xen-2.6.18-274.7.1.el5.x86_64 is intended for a x86_64 architecture
Linux etc 2.6.18-274.7.1.el5xen #1 SMP Thu Oct 20 17:06:34 EDT 2011 x86_64 x86_64 x86_64 GNU/Linux
As you can see above architecture and kernel is 64-bit but I had to force it to install using "--ignorearch"
Solution
#rpm --ignorearch -ivh kernel-xen-2.6.18-274.7.1.el5.x86_64.rpm
Preparing...&nb........
These drives seem to die very easily during shipping:
sd 0:0:0:0: [sda] Unhandled error code
sd 0:0:0:0: [sda] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
sd 0:0:0:0: [sda] CDB: Read(10): 28 00 18 8b 65 e0 00 00 08 00
end_request: I/O error, dev sda, sector 411788768
sd 0:0:0:0: [sda] Unhandled error code
sd 0:0:0:0: [sda] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
sd 0:0:0:0: [sda] CDB: Read(10): 28 00 18 8b........
This is just trying to read 5GB off the drive with dd and the drive initially tested ok but shortly after I wondered why I was seeing 2MB/s read speeds. Notice the "current_pending_sector", anytime I've seen it at anything above 0 even with no other bad fields/attributes, it means the drive is bad.
ata1.00: exception Emask 0x0 SAct 0x3 SErr 0x0 action 0x0
ata1.00: irq_stat 0x40000008
ata1.00: failed command: READ FPDMA QUEUED
ata1.00: cmd 60/00:00:........
This is something many people and especially businesses worry about, or at least they should. Before throwing away a hard drive, returning a hard drive, or especially Warrantying/RMAing it, you should wipe the drive.
Linux provides the "shred" and "dd" utlities which work quite well. It seems even a single pass is good enough but by default shred will do 3 passes.
Here's an example of using shred in Linux (I use a custom made distribution from........
If you move your hard drive(s) around to other computers/servers, you'll find that your eth0 keeps getting higher, the first time it will become eth1 and then eth2 etc and even higher if your server has dual or quad NICs. The reason is that udevd basically assigns eth0 tot he first NIC it finds and remembers it, if it encounters a NIC with a differentMAC, it assigns it one higher (eg. eth1).
See the example below, I have eth2 now so how doI fix it?........
Client Log
OpenSSH_4.3p2, OpenSSL 0.9.8e-fips-rhel5 01 Jul 2008
debug1: Reading configuration data /etc/ssh/ssh_config
debug1: Applying options for *
debug1: Connecting to 192.168.1.253 [192.168.1.253] port 22.
debug1: Connection established.
debug1: permanently_set_uid: 0/0
debug1: identity file /root/.ssh/identity type -1
debug1: identity file /root/.ssh/id_rsa type 1
debug1: identity file /root/.ssh/id_d........
mdadm --manage /dev/md3 --add /dev/sda1
cat /proc/mdstat
Personalities : [raid1] [linear] [multipath] [raid0] [raid6] [raid5] [raid4] [raid10]
md0 : inactive sdd2[1] sdd1[2](S)
31270272 blocks
md3 : active raid1 sda1[2] sdb1[1] sdc1[3](F)
943730240 blocks [2/1] [_U]
[>....................]........
Here's what SMART tells me the serial number is:
=== START OF INFORMATION SECTION ===
Device Model: Hitachi HDS721010CLA332
Serial Number: JP2940HQ3ZY7KH
Firmware Version: JP4OA3EA
User Capacity: 1,000,204,886,016 bytes
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 8
ATA Standard is:&nb........
[1433128.139339] sd 5:0:1:0: [sde] Unhandled error code
[1433128.139343] sd 5:0:1:0: [sde] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[1433128.139348] sd 5:0:1:0: [sde] CDB: Read(10): 28 00 00 00 00 00 00 00 08 00
[1433128.139360] end_request: I/O error, dev sde, sector 0
[1433128.139410] sd 5:0:1:0: [sde] Unhandled error code
[1433128.139414] sd 5:0:1:0: [sde] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[1433128.139420] sd 5:0:1........
This booting error is because the Xen PV guest image uses the Xen kernel, this is not compatible with anything but a host running a Xen kernel.
I did a kpartx -av virtual.img and then it created some partitions that showed up in fdisk.
I mounted it and did a chroot into it and removed the xen kernel and installed a normal kernel but Xen still shows the same kernel in Grub (only the Xen one).
This is strange but it seems like this Xen PV guest has some sort of hidden or........
ntpd[7047]: can't open /var/lib/ntp/drift.TEMP: Permission denied
chown ntp.ntp /var/lib/ntp/
The solution is shown above and changes the ownership to ntp.ntp which is what the ntpd daemon/server is running as. This is based on Centos but the same idea will apply on any other OS. You can do a "ps aux|grep ntpd" to see what it is running as in the case it's running as a different user.
After that this annoying message wil........
VBoxManage modifyhd XP.vdi --resize 15000
VBoxManage modifyhd XP.vdi --resize 15000
0%...10%...20%...30%...40%...50%...60%...70%...80%...90%...100%
That resizes the virtual hard drive image "XP.vdi" to 15000MB instantly.
I doubt this is safe to do while the VM is running and I'm not sure if it would attempt it still but turn the VM off first to be safe.
I also notice in the VBOX GUI that it still shows the orig........
I've encountered this problem before and I believe it may affect other drivers (I could test but I don't have time). This was happening on my custom Linux system with the pcnet32 driver.
pcnet32: eth0: transmit timed out, status 97fb, resetting (and some other kernel module tracing in dmesg)
Basically it means the card is connected (it shows connected in full duplex etc.. and recognized if the cable is disconnected too) but no packets can be sent or received........
I dread updating the kernel and rebooting to find the Ubuntu graphics aren't working and you have to manually intervene. This is usually because Ubuntu for whatever reason didn't update the drivers you need (eg. the manually compiled Nvidia Kernel driver that MUST be recompiled for each and every kernel update unfortunately).
The most common reason may be that "linux-source" hasn't been installed automatically on my system. I tried to manually reinstall the........
I really am a Linux fan but my comments here may not show it. Although I'm quite familiar with Linux CLI to administer servers, I find Linux GUI OS's like Ubuntu at times very clunky.
This is partially because there's no such thing as a "self-made" Linux from scratch where the UIwas designed by a single team. Linux is made up of several different projects that are generally completely separate and this lack of integratiion is a key issue that makes things f........
I like dd, although it only reads it, usually a read test of the entire disk will uncover if your hard drive is bad in some parts. This is a good thing to do at least once a month, a lot of times bizarre program behavior, laginess and crashing/unnmounting problems etc.. are due to a failing disc and SMART won't know it or indicate a problem:
We must also remember there's never a guarantee, I've found that ever since we moved to larger and more platters per drive with 1TB drives........
In file included from drivers/block/cciss.c:1015:
include/asm-generic/pci-dma-compat.h: In function `cmd_special_free':
drivers/block/cciss.c:196: sorry, unimplemented: inlining failed in call to 'cciss_tag_discard_error_bits': function body not available
include/asm-generic/pci-dma-compat.h:25: sorry, unimplemented: called from here
make[2]: *** [drivers/block/cciss.o] Error 1
make[1]: *** [drivers/block] Error 2
make: *** [drivers] Error 2........
My Samsung drive failed on me, at first I thought it was the enclosure but a direct SATA connection causes the same problems for discs that are inserted. It will work fine for a few minutes but then starts spewing the errors below.
I've never been a fan of Korean made optical drives and have always had trouble with them. The problem is that I don't believe NEC and Lite-ON make drives anymore, and I considered them the leaders.
Apr 7 11:58:48 bo........
hdparm -B 255 /dev/sdb
/dev/sdb:
setting Advanced Power Management level to disabled
HDIO_DRIVE_CMD failed: Input/output error
The one thing you can do though is to set hdparm spindown time lower (it doesn't seem to work that well).
-S set standby (spindown) timeout
hdparm -S 251 /dev/sda
/dev/sda:
setti........
I am a huge fan of Linux and the idea of OpenSource but I've said it many times, there are still hurdles in today in 2010 for Linux as a Desktop. Linux is still intended for servers at its very core. This can be changed succesfully though, as Apple has shown us with Mac OS X based on FreeBSD.
Half of the issue is lack of driver support and the other half is the Linux Kernel and Window Manages, KDE and GNome still both don't cut it (but they're getting closer).
I'll........
[27969.398749] sd 5:0:0:0: [sdb] 3907029168 512-byte hardware sectors (2000399 MB)
[27969.398749] sd 5:0:0:0: [sdb] Write Protect is off
[27969.398749] sd 5:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[27969.398749] sd 5:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[27972.117543] ata6.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x0
[27972.117543] ata6.00: irq_stat 0x48000000
[27972.117543] ata6.00: cmd 60/08:00:ff:7........
This is obviously a bug in the r8169 kernel module and it seems to affect a lot of people. I upgraded to the latest kernel and hope this won't happen anymore, as it is a very serious error. This is especially serious for those who are running servers with this chipset, who can afford for the NIC to randomly go off-line for no apparent reason?
[655548.189113] type=1505 audit(1277067560.902:5): operation="profile_load" name="/usr/bin/freshclam&q........
I'm using Ubuntu 8.04 but anyone using older kernels will find this may apply to them. My Intel graphics are very slow with the default Xorg settings but by using "EXA" acceleration, scrolling down windows of text becomes pretty snappy.
Just edit /etc/X11/xorg.conf
Section "Device"
Identifier "Configured Video Device"
&nb........
Basically the two main types of distros are Debian and RHEL/Centos based. I'm just going to give a quick overview of how the configuration of IP interfaces works in Debian/Centos based distros.
*Just one thing to remember, when setting IPs statically you have to manually specify a DNS server in /etc/resolv.conf (since DHCP is what normally does it automatically)
Debian/Ubuntu/Kubuntu/MEPIS
The IP (DHCP &........
CC drivers/message/fusion/mptsas.o
drivers/message/fusion/mptsas.c: In function `mptsas_port_delete':
drivers/message/fusion/mptsas.c:106: sorry, unimplemented: inlining failed in call to 'mptsas_set_rphy': function body not available
drivers/message/fusion/mptsas.c:462: sorry, unimplemented: called from here
make[3]: *** [drivers/message/fusion/mptsas.o] Error 1
make[2]: *** [drivers/message/fusion] Error 2
mak........
This drive is clearly on the way out, the Kernel knows it but I'm surprised that SMART is not concerned. I didn't blame Seagate for their past issues until now. This hard drive has hardly been used and has not even been powered on for a year according to SMART.
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda 7200.11
Device........
Seagate Inventory/Firmware Check
I heard about this issue a long time ago but never looked into it. I figured I wasn't affected since my 500GB drives were running for so long. I've been using Seagate's since 2002 and to this day all of the drives I have are alive from Seagate.
*Update the bad news is that I realize one of my 500GB's is about to die, it's not even a year old, but is also not affected by the recall according to Seagate!
Seagate Inventory/Firm........
*This is a bug with initramfs support, all kernels after around 2.6.27.54 suffer from this problem.
If you try to include initramfs into your kernel (I mean actually building your binaries into the kernel) this will always happen. Obviously some code has changed in recent kernels that is present in all new kernels, it makes it impossible to boot
I've tried the latest 2.6.32, 2.6.33, 2.6.34, 2.6.35, 2.6.36, 2.6.37, 2.6.38 kernels and they all do this. I found one bug re........
Linux Kernel v2.6.30.3
102220 blocks
CHK include/linux/version.h
CHK include/linux/utsrelease.h
SYMLINK include/asm -> include/asm-x86
CALL scripts/checksyscalls.sh
CHK include/linux/compile.h
CC drivers/net/igb/igb_main.o
drivers/net/igb/igb_main.c: In function `igb_up':........
I wanted to disable the "Administrator" account for security purposes and Iread some "guide" on the internet that recommended that we run "C:WindowsSystem32sysprepsysprep.exe /generalize". I also clicked the option for "Generalize" and the computer rebooted and gave some OOBE error and restarted, and now I get the error above no matter what.
I read that some drivers such as ones from AVIRA AV can cause this because they're unsign........
Inever saved any of the logs, but basically no matter what OS (Linux)I used, I could not get my 1000GB hard drive to work (Seagate SATA). The BIOS recognizes the drive and fdisk -l shows the hard drive as it should.
The tricky thing is that different OS's will give you different results, but don't be fooled. You can't use these larger drives for long. Iwas getting all kinds of seek/IOerrors and also messages that the port could not be read.........
This will give you the basic info needed to browse and connect to Samba shares from the command line. From the GUI of Gnome or KDE etc, it is pretty standard and straight forward. However, I've found very little guides on how to do it from the command line and if you're like me, a nerd who prefers command line for its simplicity and for remote use, this is the way to go.
First get a list of all the Samba/SMB shares on the target.
smbclient -L hostname........
There's a lot of outdated information and confusion for system administrator's out there.
One annoying task for many an Administrator has been backing up data in Linux. You don't need any GUI tools such as K3B or GnomeBaker. Both are excellent tools but for veteran command line users working remotely, using the keyboard is a great and possibly automated way to save yourself pain and hassle.
At a later date we'll cover how scripting can automatically backup certain........