This seems to happen in many different drivers but it happened more often in newer versions such as 530 vs 525. Then nvidia-modeset goes to 100% There are many reports of this appearing since driver 4.70 and I can confirm I've seen this in various machines. https://forums.de........

This should work for most console ports of other manufacturers too. It is a quick and simple method for emegencies or deploying a few appliances/devices in a non-standard environment or small environment. However, if this is a route thing, or the equipment is not physically close to you, it would be best to use some sort of "Terminal" server which is an IP connected switch with several serial ports built-in for this purpose. Normally they accessible by web/........

It may appear to be an Xorg or lightdm/gdm/mdm error but in reality for many users with this issue, it's a driver conflict and issue. I had a system that had two GPUs, an Intel and Nvidia GPU. The only thing that got it working was to remove the nouveau driver and blacklist it so it never came back, then the Intel GPU works fine without these issues. Solution sudo rmmod nouveau add nouveau/other driver to blacklist edit th........

One easy way is to use lspci -k like this: sudo lspci -k|grep modules|sort -nr|uniq Kernel modules: snd_hda_intel Kernel modules: shpchp Kernel modules: pata_acpi Kernel modules: nvidiafb, nouveau, nvidia_drm, nvidia Kernel modules: mei_me Kernel modules: lpc_ich Kernel module........

This is the reason that I don't like the new ADATA USB drives such as the UV128/64GB or 128GB drives and other ones that look to be the same style (the green sliding USB connector). They just don't work well from new and never work properly at any point. [ 788.242463] usb 1-1.2: new high-speed USB device number 16 using ehci-pci [ 788.339816] usb 1-1.2: New USB device found, idVendor=125f, idProduct=db8a [ 7........

4.374647] usb_common: exports duplicate symbol usb_get_dr_mode (owned by kernel) [ 4.403334] usbcore: exports duplicate symbol __usb_get_extra_descriptor (owned by kernel) [ 4.427736] xhci_hcd 0000:00:15.0: xHCI Host Controller [ 4.427844] xhci_hcd 0000:00:15.0: new USB bus registered, assigned bus number 1 [ 4.429040] xhci_hcd 0000:00:15.0: hcc params 0x200077c1 hci version 0x100 quirks 0x01109810 [ 4.429141] xhci_hcd 0000:00:15.0: cache line size of 64 is not sup........

This is a 8TB Seagate external USB 3.0 device apparently newer kernels use a module called "UAS" instead of "USB Storage" which causes issues as a lot of devices are not properly supported in UAS mode by the kernel driver. The solution some say is to disable UAS specifically for your USB device but I'd rather just disable UAS altogether. Solution blacklist UAS: *do not do this it does not work and just causes your USB 3.0........

When running cudaminer once it tries to initialize the card the entire screen freezes. The computer itself is still running but the Xorg is done for, you cannot even switch to another console window and must reboot (even an mdm or Xorg restart does not help). At first cudaminer will give you these errors: stratrum_recv_line failed ...retry after 15 seconds GPU #0: Geforce 210 with compute ca........

Here is a simple MP3 player and now there's a reason to understand why the supplied cable has some kind of capacitor and is very short. These devices can be VERY finicky and any voltage fluctuation or difference is enough to cause issues. Take for example the error messages from Linux Mint: [804829.895414] usb 1-1: USB disconnect, device number 11 [806961.109030] usb 1-1: new high-speed USB device number 12 using xhci_hcd........

Normally the below would indicate a failing or failed drive. In this case the SATA port was unplugged and sometimes the Linux kernel/motherboard even with AHCIjust don't play nice and can't handle it. What happened is Iplugged in a new drive after removing another one. However the log shows that after the old drive was plugged in the Linux kernel kept complaining thinking the drive was there but not responding properly. This continued even with reseating........

At first my BIOS said the card may not work right because there is no more option ROM space. I disabled the Option ROM for both LSI 1068 and 2008 chipsets, Network Boot ROM and most other PCI slots, Serial Port, etc... and the message went away but the card still does not work properly. But it still cannot initialize the card properly(does not work): [ 33.943272] NVRM: This PCI I/O region assigned to your NVIDIA device is invalid:........

Dell CS24SC Info 0000:00:00.0 Host bridge: Intel Corporation 5100 Chipset Memory Controller Hub (rev 90) 0000:00:02.0 PCI bridge: Intel Corporation 5100 Chipset PCI Express x8 Port 2-3 (rev 90) 0000:00:03.0 PCI bridge: Intel Corporation 5100 Chipset PCI Express x4 Port 3 (rev 90) 0000:00:04.0 PCI bridge: Intel Corporation 5100 Chipset PCI Express x16 Port 4-7 (rev 90) 0000:00:05.0 PCI bridge: Intel Corporation 5100 Chipset PCI Express x4 Port 5 (rev 90)........

0000:00:00.0 Host bridge: Intel Corporation 5000P Chipset Memory Controller Hub (rev b1) 0000:00:02.0 PCI bridge: Intel Corporation 5000 Series Chipset PCI Express x8 Port 2-3 (rev b1) 0000:00:03.0 PCI bridge: Intel Corporation 5000 Series Chipset PCI Express x4 Port 3 (rev b1) 0000:00:04.0 PCI bridge: Intel Corporation 5000 Series Chipset PCI Express x8 Port 4-5 (rev b1) 0000:00:05.0 PCI bridge: Intel Corporation 5000 Series Chipset PCI Express x4........

LSi Megaraid At first it was configured as a RAID 0, then I deleted the Virtual Disk Group. I thought both drives would be shown and detected in Linux as sda and sdb but it actually shows nothing. To make them work you have to hit Ctrl+R before the system boots (when prompted) and create a Virtual Disk Group. In my case I created each one as RAID 0 (with a single drive only) as I just wanted JBOD but there is no such option or default in these Dell Pe........

This is the most I can get when plugging in a hard drive hot and only on some power connectors. [71656.314271] ata5: exception Emask 0x50 SAct 0x0 SErr 0x90a02 action 0xe frozen [71656.314277] ata5: irq_stat 0x00400000, PHY RDY changed [71656.314285] ata5: SError: { RecovComm Persist HostInt PHYRdyChg 10B8B } [71656.314294] ata5: hard resetting link [71660.360686] ata5: softreset failed (device not ready) [71660.360694] ata5: applying........

This pops up when connecting the phone and it doesn't seem to charge. The phone keeps showing a status message every few seconds "Connected as a media device". It's ridiculous why this phone doesn't just default as a simple USB Mass storage device. Here's what I see in /var/log/messages: Jan 30 18:51:27 QuadCoreAM2 kernel: [18038228.144046] usb 1-3: new high speed USB device using ehci_hcd and address 24 Jan 30 18:51:28 QuadCoreAM2 ke........

This booting error is because the Xen PV guest image uses the Xen kernel, this is not compatible with anything but a host running a Xen kernel. I did a kpartx -av virtual.img and then it created some partitions that showed up in fdisk. I mounted it and did a chroot into it and removed the xen kernel and installed a normal kernel but Xen still shows the same kernel in Grub (only the Xen one). This is strange but it seems like this Xen PV guest has some sort of hidden or........

This is obviously a bug in the r8169 kernel module and it seems to affect a lot of people. I upgraded to the latest kernel and hope this won't happen anymore, as it is a very serious error. This is especially serious for those who are running servers with this chipset, who can afford for the NIC to randomly go off-line for no apparent reason? [655548.189113] type=1505 audit(1277067560.902:5): operation="profile_load" name="/usr/bin/freshclam&q........

From the package "parted" you can use the command "partprobe" to re-read the partition table. I really hate rebooting, and that's what Iloved to hear about AHCI motherboards, that they allow hotswap so you don't have to reboot. But that's only as good as the OS, if the OS does not reload the partition table you won't be able to do anything with that new drive you attached without rebooting. Yes, even without re-reading the partiton table Linux will........

This is the Intel Atom 330 motherboard with integrated Realtek Gigabit NIC (Intel Desktop Board D945GCLF2 Motherboard W/ Atom 330 1.6 GHz Dual Core Processor - Mini-ITX) I cannot achieve more than 15 MB/s, even doing a local transfer through eth0 to it's own IP. 100% 95MB 15.9MB/s 00:06 So this is not a cabling, switch or hardware issue, it seems like a driver or chipset limitation problem. Here is my........

When trying to even cd or ls the mounted OCFS2 partition it crashes. Ithink this is a combination of VMWare Server's problem and the way I mounted and symlinked to it. More than anything this shows the problem and lack of forsight with VMWare, but also that OCFS2 is easily crashed if you do strange things. Output of /var/log/messages for OCFS2 Apr 10 15:57:45 localhost kernel: [84331.691258] Modules linked in: vmnet vmci vmmon ocfs2_stac........