In a lot of distros, vdpau which accelerates video through the GPUis often not installed even in recent distros. This will result in Firefox with Youtube dropping frames when you check the "Stats for Nerds" and to the eye as jerky or slower video playback due to the dropped frames.
Some sites will say that because you are watching VP09 that there is no GPU support, but with vdpau installed and enabled, many GPUs will still be able to use hardware decoding for 4K........
This example is using RTL8821AU chipset from a TP-Link T2U Plus USB adapter and other similar ones should work the same.
Here's how to get this chipset RTL8821AU working in Linux.
Here's how to get RTL8812 and RTL8822 working in Linux.........
This is certainly a poor design, as you can read many seasoned admins who have updated their iDRAC only to have it killed. One possible cause is not by doing all the incremental updates, doing updates from an old iDRAC to one many revisions newer is a sure way to kill things, but even then there is no guarantee based on the amount of failures.
List of threads of people's dead iDRAC's:........
This guide assumes you have a working Postfix server and want it to sign with DKIM.
There are a few things we have to understand to make all of this work though, which require you to be familiar with DNS as well.
1.) Install OpenDKIM
apt install opendkim
systemctl enable opendkim
2.) Edit /etc/opendkim.conf
Syslog yes
SyslogSuccess yes
Mode&nbs........
apt install tftpd-hpa
#change TFTP_ADDRESS to by setting address to 192.168.1.1:69 or the IP you need, otherwise it will listen on all IPs and interfaces which could be a security risk.
# edit /etc/default/tftpd-hpa
TFTP_USERNAME="tftp"
TFTP_DIRECTORY="/srv/tftp"
TFTP_ADDRESS="192.168.1.1:69"
TFTP_OPTIONS="--secure"........
This sometimes happens when trying to install the EFIversion of grub to a device when you are booted into Legacy/MBR mode. It doesn't seem to occur on all machines, but some and seems somewhat BIOS dependent.
grub-install --target=x86_64-efi /dev/sda
Installing for x86_64-efi platform.
grub-install.real: warning: Couldn't find physical volume `(null)'. Some modules may be missing from core image..
grub-install.real: warning: Couldn't find physica........
sysctl vm.overcommit_memory=1
echo never > /sys/kernel/mm/transparent_hugepage/enabled
echo 511 > /proc/sys/net/core/somaxconn
1:M 26 Nov 2023 21:34:33.840 # WARNING: The TCP backlog setting of 511 cannot be enforced because /proc/sys/net/core/somaxconn is set to the lower value of 128.
1:M 26 Nov 2023 21:34:33.840 # Server initialized
1:M 26 Nov 2023 21:34:33.840 # WARNING overcommit_memory is set to 0! Background sa........
This seems to happen in many different drivers but it happened more often in newer versions such as 530 vs 525.
Then nvidia-modeset goes to 100%
There are many reports of this appearing since driver 4.70 and I can confirm I've seen this in various machines.
https://forums.de........
Sometimes users take their removal drives and unplug and replug them to test what happens during the failure of a disk. However, this breaks things quite badly due to the /dev/mapper in LUKS not coming back online due to it not being closed.
In other words, generally with non-encrypted drives the process is smooth but when encrypted you may want to follow a strategy like this:
We can see below that both disks are unavailable as they were physically remov........
This is a weird issue as sometimes when upgrading or even migrating, this could happen and the reason is simple but maybe not 100% obvious at first.
You will find that your GUIdoesn't load and most services fail to start, even logind
Here are some errors you may see:
Mar 13 22:22:23 rttbox systemd-logind[2892]: Failed to connect to system bus: No such file or directory
Mar 13 22:22:23 rttbox systemd-logind........
A lot of companies are unsure which solution to choose and many may not be aware of Docker Swarm as an alternative to Kubernetes. One thing that many Sysadmins find is that Docker Swarm is simply easier, quicker to setup and maintain by far than Kubernetes.........
When Is It Time to Leave Your VPS, VDS, and Dedicated Server Provider?
Choosing the right hosting solution—be it Virtu........
This will be the goto to help solve e-mail delivery issues and talk about many practical issues that happen between developers, admins and scripts that send e-mail and do things that may not be acceptable or cause deliverability problems.
Sendmail Stuff
Edit /etc/mail/sendmail.mc
The problem is that if you send directly out from the server using the mail function, the Return-path of the e-mails will be username@thehostnameoftheserver.com. Let........
First we need a few extra packages:
apt update
apt install -y adduser libfontconfig1 musl sudo
wget https://dl.grafana.com/enterprise/release/grafana-enterprise_10.3.1_amd64.deb
Install / Enable Grafana
dpkg -i grafana-enterprise_10.3.1_amd64.deb
dpkg -i grafana-enterprise_10.3.1_amd64.deb
(Reading database ... 44309 files and directories currently installed.)
Preparin........
This is for the situation that you're doing other things that may conflict or have your own custom rules and ufw keeps overriding iptables.
A lot of guides don't work, and even ufw reset does not work, because it still leaves the old ufw chains.
Here is what works to disable ufw completely
systemctl stop ufw
systemctl disable ufw
ufw disable
rm -f /et........
find /usr/share/zoneinfo/|sed s#"/usr/share/zoneinfo/"##g|grep "/"|grep -v posix|grep -v ^"Etc/"|grep -v ^right|grep -v ^"SystemV"
Africa/Addis_Ababa
Africa/Abidjan
Africa/Blantyre
Africa/Lusaka
Africa/Casablanca
Africa/Libreville
Africa/Asmara
Africa/Bujumbura
Africa/Dakar
Africa/Lagos
Africa/Malabo
Africa/Harare
Africa/Kigali........
Step 1.) Upgrade to Debian 11 first
The process to go to Debian 12 is not as smooth as 11, when trying to upgrade from Debian 10. In fact, it doesn't work directly, so you'll first need to follow this guide to update to Debian 11, reboot and come back here if successful.
Step 2.) Update sources.list
Update your /etc/apt/sources.list like this:
deb http://........
If you get this error, it is often because you have configured Apache with modules that weren't actually installed. Eg. you try to load the PHPmodule but didn't actually install the apache2 php module, so the server can't start. In general, this error can often be caused by issues with problematic modules and/or Apache being configured for modules that have not actually be installed (eg. libapache2-mod-php) is missing.
The above results in this less than obv........
The issue is that Docker images are stripped down, so many tools and even python3 is missing, so you'll have to build or update the actual image yourself.
I assume you have started an image with something like this and that you have the Nvidia Toolkit installed (assuming you are using GPUs). If you're not using nvidia just remove --runtime=nvidia --gpus all.
docker run -it --runtime=nvidia --gpus all ubuntu bash
These works for most images li........
Welcome to our in-depth guide on configuring NVIDIA GPUs with Docker on Ubuntu. This post is tailored for developers, data scientists, and IT professionals who are looking to leverage the power of NVIDIA's GPU acceleration within Docker containers.
Whether you're working on machine lea........
You'll notice that /etc/resolv.conf contains dire warners on most Linux Desktops.
# This file is managed by man:systemd-resolved(8). Do not edit.
#
# This is a dynamic resolv.conf file for connecting local clients to the
# internal DNS stub resolver of systemd-resolved. This file lists all
# configured search domains.
#
# Run "resolvectl status" to see details about the uplink DNS servers
# currently in use........
How to check what kernel version you have/currently running?
uname -rm
5.4.0-91-generic x86_64
The above shows us that we are running 5.4.0-91-generic on the x86_64 architecture.
The safest way is to stick with the same flavor eg if you're on generic, and say on kernel 5.4.0 then it makes sense to follow what is below. However, if you are migrating or dual booting between newer hardware (eg. you got a........
We could always disable swap but this would normally be a bad idea unless you have an incredible amount of RAM and a workload that will never exceed it. However, for live/containerized and high performance environments it could be desirable.
Another middle ground may be to set swappiness to a lower number.
You may also want to clear your kernel's cache, which could be eating up RAM unnecessarily by c........
request_module: runaway loop modprobe binfmt-464c Kernel panic - not syncing: No init found Pid: 1, comm: swapper/0 Not tainted
This is usually caused by a mismatch in architecture and happens frequently in development environments.
Here is a example of what caused this issue:
Your binaries are based on one architecture
Your kernel was compiled with another architecture.
Why does this happe........
A lot of developers want to go to 3.11 because of the speed improvements, but most distros never have the latest Python version.
Using the deadsnakes third party repo is the easiest way aside from compiling it yourself (which is safer and recommended):
Step 1 - Add the repo
apt-add-repository ppa:deadsnakes/ppa
If you get an error about requests then install it:........
If you get this error in your logs:
add bridge failed: Package not installed
This error normally means one of two things.
1.) Is your brctl (bridge-utils) installed?
On Mint/Debian check for "brctl". If it's not there do
sudo apt install bridge-utils uml-utilities
2.) Is your bridge.ko (bridge kernel module loaded?).
On some installs I have seen that you cannot modpro........
haproxy is one of the best known and widely used Open Source load balancers out there and a strong competitor to nginx.
haproxy is used by many large sites per Wikipedia:
HAProxy is used by a number of high-profile websites including GoDaddy, GitHub,........
Virtualbox is a very powerful tool, but for some use cases it is less than optimal.
Say you are in a work, lab or other environment where you are not alone on the physical network and there could be overlap of IPs, but you need all of your VMs to be contactable from your host, VMs need to communicate with each other, and VMs need internet.
NAT Network will give you VM to VM communication and internet, however, it is buggy and unstable. It also doesn't allow host to VM co........
In this example we install debian 10 with --variant=minbase which gives us a minimal/tiny install. Don't use variant if you want the full size install.
mkdir /tmp/deb10files
debootstrap --variant=minbase buster /tmp/deb10files/
Did you get an error?
debootstrap --variant=minbase buster /home/theuser/VMs/deb10files/
You'll get this error if you make a directory in your home........
Remember that control connections are established on port 1723 and then actual data is transferred over GRE protocol 47.
If you have a NAT setup this will work without special forwarding or accepting of GRE packets (normally if you are not blocking outgoing connections and accepting established and related connections).
The below two commands will get things going so PPTP and GRE work
We first load the ip_nat_pptp module which allows PPTP to work with........
So say you happen to have 2 NICs of the exact same chipset, they will generally show up as the same name, with possibly a different revision in lspci. Normally this is not an issue if you have a server with 4 NICs, generally the eth0 to eth3 appears from left to the right (or right to left on some vendors) so it doesn't take much figuring out.
Generally if you have different chipsets for different NICs, it should be easy to know which one is eth0 or the first NIC in the OS.........
Sometimes due to your BIOS/EFI you may find that you have chosen "Energy Efficient" for your CPU which may effectively disable turbo mode. This is because "Energy Efficient" will often restrict or throttle your CPU to the base speed. This can impact nearly any CPU such as Intel's, AMDs, Opteron, Xeon etc...
This is of course frustrating, for example if you have a CPU that is 2.0GHz base speed but turbo to 2.5GHz, you will never hit more than 2GHz.........
It sounds intuitive that you may just move the /var/lib/docker dir to another location and symlink it back but it won't work and you'll get an error.
How to move Docker Storage the Correct Way
This assumes that you want to use /mnt/raid as the new location.
1.) Stop Docker
systemctl stop docker
2.) Move /var/lib/docker
mv /var/lib/docker /mnt/raid/
3.) Edit the Docker daemon file
Specify the path you wan........
PCIID 2357:0138
First install your kernel headers/source:
sudo apt install linux-headers-`uname -r`
1.) Clone this git repo
git clone https://github.com/morrownr/88x2bu-20210702
2.) Run the install
cd 88x2bu-20210702
./install-driver.sh
3.) Load the driver
mod........
If you are getting this error from systemctl "Loaded: masked (Reason: Unit hostapd.service is masked.)" we need to unmask the service.
Solution
systemctl unmask hostapd
Removed /etc/systemd/system/hostapd.service.
It's fixed
root@routerOS:/var/log# systemctl start hostapd
root@routerOS:/var/log# systemctl status hostapd
● hostapd.service - Access point and authentication server for Wi-Fi and Ethern........
Just an FYI that the installer ignores your selection of Boot Loader, as it was intended for MBR/Legacy. The installer horribly, even when choosing "Something Else" and manually partitioning and creating an EFIin your install drive, will still install grub to the first EFI partition it finds, even if you are following a guide like this to avoid wiping out the M........
A quick fix is to run this command:
sudo brctl setageing br0 0
This causes the aging of the MAC address to time out immediately or in 0 seconds, which delete the entry frmo the FDB (Forwarding Database) and causes the error to go away. The default time is 300 seconds or 5 minutes.
You can also add it under your br0 definition like this in /etc/network/interfaces to make it permanent and automatic:
auto br........
NetworkManager is normally good for GUI users who may not be good with manually confguring devices, but if you are using things like bridging and bonding, it will often break things.
How To Disable NetworkManager
systemctl disable NetworkManager
Now that it's disabled you will need to stop NetworkManager. NetworkManager will still be running until you reboot next or manually stop it.
How To Stop NetworkManager
systemctl stop........
Is your /var/log/journal overweight and bloated? For example a decent install of Debian 11 with most applications and services ends up being about 4.9G with the journal taking a few gigs.
du -hs /var/log/journal/
1.3G /var/log/journal/
By default in a lot of distributions there is no maximum size so it will keep growing. This is especially problematic for embedded distributions and devices, but is also a huge waste of sp........
Usually LIbreoffice gets it right, but if it opens a normal English CSV as UTF-16 by default and shows Asian languages, you'll have ot manually open to fix it (don't double click the file from the File Manager).
Solution - Manually Open the File After Opening LibreOffice Calc
You'll see it is defaulting to UTF-16 which breaks everything.
........
The easiest way for the 8821AU Realtek Wifi chipset / TP-Link T2U Plus:
Bus 002 Device 003: ID 2357:0120 TP-Link Archer T2U PLUS [RTL8821AU]
First install your kernel headers/source/other required tools:
sudo apt install linux-headers-`uname -r` make gcc bc
Clone this github repo with the driver:
git clone https://github.com/morrownr/8821au-20210708
Run the compile/ins........
Bonding is an excellent way to get both increased redundancy and throughput. It is similar to the "Network Teaming" feature in Windows.
There are a few different modes but we will use mode 6, I think it's the best of both worlds, as it is not just a failover, but it provides round robin, so you will get redundancy and load balancing. So if you have a 1G single port, you will have a combined throughput of 4G at this point. Just bear in mind that the true thr........
If you are using mint, delete the preference that stops snap from installing (as it is required for lxc)
sudo rm /etc/apt/preferences.d/nosnap.pref
1. Install lxd:
sudo apt install lxd
Issues install lxd or errors? Click here
Debian at this time does not have lxd so you'll need to use snap:
sudo apt in........
This can be used on almost anything, since Gluster is a userspace tool, based on FUSE. This means that all Gluster appears as to any application is just a directory.
Applications don't need specific support for Gluster, so long as you can tell the application to use a certain directory for storage.
One application can be for redundant and scaled storage, including for within Docker and Kubernetes, LXC, Proxmox, OpenStack, etc or just your image/web/video files or even da........
freshclam
ClamAV update process started at Sun Mar 20 00:30:50 2022
WARNING: Your ClamAV installation is OUTDATED!
WARNING: Local version: 0.100.3 Recommended version: 0.103.5
DON'T PANIC! Read https://www.clamav.net/documents/upgrading-clamav
main.cld is up to date (version: 62, sigs: 6647427, f-level: 90, builder: sigmgr)
WARNING: getpatch: Can't download daily-26337.cdiff from db.local.clamav.net
WARNING:........
(firefox:9562): LIBDBUSMENU-GLIB-WARNING **: Unable to get session bus: Failed to execute child process "dbus-launch" (No such file or directory)
ExceptionHandler::GenerateDump cloned child 9743
ExceptionHandler::WaitForContinueSignal waiting for continue signal...
ExceptionHandler::SendContinueSignalToChild sent continue signal to child
[Parent 9562, Gecko_IOThread] WARNING: pipe error (40): Connection reset by peer: file /build/firefox-EymEXX/fire........
Install procps and it will install the other packages you need:
apt install procps
Reading package lists... Done
Building dependency tree
Reading state information... Done
The following additional packages will be installed:
libgpm2 libncurses6 libprocps7 lsb-base psmisc
Suggested packages:
gpm
The following NEW packages will be ins........
There is a random bug that sometimes occurs with Vbox NAT mode DNS, although it has never happened in the past and Vbox was working fine until recently.
The symptom is that you can see it does get an IP+ DNS from the Vbox NAT DHCP.
Below we use resolvectl dns and verify the DNS server is set to 10.0.2.3 which is the DNS from Vbox NAT. We can ping it but it does not respond to any DNS requests when we use dig @10.0.2.3 realtechtalk.com........
The Best Docker Tutorial for Beginners
We quickly explain the basic Docker concepts and show you how to do the most common tasks from starting your first container, to making custom images, a Docker Swarm Cluster Tutorial, docker compose and Docker buildfiles.........
Why choose OpenVPN instead of a firewall appliance?
OpenVPN can be a reliable and easy replacement for traditional hardware or just be an additional tool that your company uses so that the firewall can focus on its job rather than acting as a VPNappliance at the same time.
When comparing OpenVPN with traditional firewal........
These types of errors are normally caused by misconfiguration of your /etc/apt/sources.list.
In this example on Debian 10, if you didn't complete the install correctly, you will have no repos enabled and only rely on CDROM.
"Package wget is not available, but is referred to by another package. This may mean that the package is missing, has been obsoleted, or is only available from another source.
E: Package 'wget' ha........
How To Install Wazuh Server / Quickest Installation
Wazuh (forked from the well known OSSEC project) is a full SIEM (Security Information Event Management) that works extremely well with the platforms it natively supports as an "Agent", which allows you to do scans of everything such as all processes running, CVE vulnerability check, incident reporting etc...
Prerequisites:
A lot of issues with Wazuh seem to be caused by i........
A lot of newer installs will automatically prohibit the root user from logging in directly, for security reasons or they will only allow key based access.
If you know what you are doing/don't care about security or have an incredibly secure password for testing, then you can enable it.
Edit this file: /etc/ssh/sshd_config
Find the following line: PermitRootLogin
Set it like this:
PermitRootLogin yes
Now rest........
1. Let's work from an environment where we can install Ansible on.
If you are using an older version of Linux based on Mint 18 or Ubuntu 16, you may want to get the PPA and get the latest version of Ansible that way:
sudo apt install gpg
sudo add-apt-repository ppa:ansible/ansible
sudo apt update........
Here is the scenario, you are using QEMU/KVM and are using something like the AC97 sound driver to pass the host audio to the guest via pulseaudio. This is useful because you can transparently pass your mic input from the host which means you can mute your microphone from the host, which prevents the guest from receiving any mic input even if unmuted.
Mute / Unmute Fix
This issue also seems to happen even if you press the mute button on the microphone and then unmute,........
The Linux Mint team has disabled it by setting an apt preference, you can edit or just remove the file:
sudo apt install snapd
Reading package lists... Done
Building dependency tree
Reading state information... Done
Package snapd is not available, but is referred to by another package.
This may mean that the package is missing, has been obsoleted, or
is only available from another source........
Kubernetes Easy Beginners Tutorial/Architecture Guide
Kubernetes is known as container orchestration and we should start at explaining the container part of it.
A Container is what runs the actual application and based on an Image, and are more comparable to something like an LXC Container, Virtuozzo/OpenVZ using the Linux Kernel Namespaces feature. Containers run these images as independent, isolated operating environments under the O........
vi is very handy when doing a lot of config file editing and can save you time over using the mouse or using the x or delete keys to manually delete.
Solution:
If you don't want it to stop deleting when encountering things like - or _, then you want this:
d$
Or if you want it to stop on - and _ then use this:
dw
Remember both commands are in "non-input mode" so not when you're........
Usually if you get the grub boot loader and it doesn't show any boot options, it's because grub was not installed correctly and/or the partition that it is supposed to be on has changed or does not exist. It can also happen if you install Linux to one drive, but the boot loader to another by accident, whether EFI or MBR/Legacy mode.
You can normally fix your booting/bootloader/MBR/EFI it by chrooting into your root partition:
#become root
sudo su........
Just a quick note and warning is that if you are testing to see if EFIPXE booting works on a VM, MAKE SURE it actually works. For example Iinitially tested using my Distro's QEMU 2.5+dfsg-5ubuntu10.46 and ovmf BIOS firmware (OVMF supports EFI). However, I found on old versions of QEMU (like 2.5), EFIbooting with GRUB NEVER works so it may appear that you have made a mistake when everything is fine when you boot a physi........
Interestingly enough Windows 2000 works fine on QEMU 64-bit but you have to specify Pentium as your CPU otherwise it doesn't complete the install (it will not pass the detecting/setting up devices phase).
-vga cirrus is wise because it is supported by Windows 2000 and allows higher resolutions and 24-bit color.
-cpu Pentium emulates an old computer and is necessary for install to complete
-device rtl8139 is important as this oldschool Realtek 8139 NIC is supported by W........
It took a lot of fiddling to make a Huion Kamvas 13 Pro work in Linux but it simple once you know what to do. Don't bother searching as it is unlkely there is a guide out there that will actually make your tablet work.
It mainly comes down to the fact that the hid_uclogic kernel module is buggy or doesn't support MANYof these wacom based/Huion tablets properly.
What was happening with me is that Ihad the Kamvas 13 Huion setup as a secondary screen/monitor.&nb........
A very common use case is that you don't want to waste time using a video editor that requires you to open it up and manually import the video clip and audio clip, then manually delete the old audio track and import the video and new audio. That's too much work and time since we don't want to go through the hassle.
ffmpeg is our solution, all we have to do is specify 3 variables and we're done!
-i Windows2019-Server-Noaudio.mp4 is our in........
The problem is that Linux uses UTC and Windows uses the local time from the RTC. This means whenever you boot Linux or Windows and then go back to the other OS, you will find your time is incorrect because of the two different clock modes fighting.
This results in very annoying issues when booting between the two because the clock is set based on the different standards once you boot (eg. Linux UTC by default and Windows RTC). For example it may cause issues with fsck and........
Before you try to install and dual boot it is very important to understand the concept of "what boot mode your BIOS is in" and "what mode you booted the installer to".
Then follow the example of Linux Mint (but most Linux installers are very similar)to carefully understand WHERE you are installing your Boot Loader to whether that be MBR or EFI.
How Am IBooted?
First it's important to check your BIOS to see........
-?????????? ? ? ? ? ? shadow
----------. 1 root root 748 Jul 10 04:35 shadow-
cat: shadow: Input/output error
If you see this you are probably in big trouble, it could be a physical error or if it's a VM image that it is corrupted due to a physical error on the underlying disk/array/NAS or it could a........
This is very frustrating but the fix is usually easy once you read this blog. It's very frustrating when you find that your Linux / Ubuntu laptop's wifi will NEVER work unless it is plugged into the power. The wifi menu may say "Wifi disabled by hardware switch". You may find that your laptop has no switch or has a function wifi button on the keyboard but this does not work or have any effect.
The cause is usual a "wmi" kernel module and simply doing an........
apt install software-properties-common
add-apt-repository ppa:deadsnakes/ppa
apt update
apt install python3-pip
apt install python3.7 curl gnupg python3.7-dev git
ln -s /usr/bin/python3.7 /usr/bin/python3
pip3 install numpy keras_preprocessing
curl https://bazel.build/bazel-release.pub.gpg | sudo apt-key add -
echo "deb [arch=amd64] http://storage.googleapis.com/bazel-apt stable jdk1.8" | sudo tee /etc/apt/sources.list.d/bazel........
Just run this apt install command
sudo apt install pepperflashplugin-nonfree browser-plugin-freshplayer-pepperflash
After this restart your browser and check Adobe's site to verify if your Pepper flash is working and showing at least version 32.
https://helpx.adobe.com/flash-player.html
As you'll see below it will download the latest version which is currently 32 and this was not possible with the old/crappy deprecated adobe-flash plu........
I used to believe that for Desktops especially that the "ondemand" CPUfrequency changing that kernels included with Ubuntu and Debian based distros have would be sufficient for snappy performance.
However, you can feel the lack of performance on the fastest computer if you have ondemand. A lot of times even under high load 100% of your CPUfrequency in MHz will not be used.
For example a 2.8Ghz CPUmay only run at 1.8MHz or even .9GHz. Now........
yum -y install wget unzip
wget https://download.nextcloud.com/server/releases/nextcloud-18.0.2.zip
unzip nextcloud-18.0.2.zip
yum -y install php php-mysqlnd php-json php-zip php-dom php-xml php-libxml php-mbstring php-gd mysql mysql-server
Last metadata expiration check: 0:58:02 ago on Fri 13 Mar 2020 02:12:49 PM EDT.
Dependencies resolved.
===================================================================........
This is sure simple if you follow the guide but it took a lot of hacking around to make this work on Debian/Ubuntu!
Now before you ask why bother running wine and python, the reason is because Python executables are NOT cross-platform. If you run pyinstaller in Linux, that binary will only run on Linux and the same if you do it in Windows. So it is preferable if you have a single environment that you can create Linux and Windows binaries from rather than running 2 separate........
The scenario here is that you have some sort of remote headless Linux server but would like to run some programs on them and get graphical access to them. The problem is that the remote server may be an image or VMwithout any virtual GPU and even if so, it is likely without KDE or Gnome, so there's no real way to do this, unless you follow our guide.
Install xvfb
apt install xvfb
Reading package lists... D........
Occasionally my whole screen locks up and I cannot even swith to the console and I find this in my syslog:
*-display
description: VGA compatible controller
product: Mullins [Radeon R3 Graphics]
vendor: Advanced Micro Devices, Inc. [AMD/ATI]
 ........
MySQL on Debian versions is configured differently than the native local MySQL plugin so you will be disappointed when your password on the mysql client fails by default.
Here is how you reset the MySQL root password the proper and "working way"
#first we gracefully stop mysql
sudo systemctl stop mysql;
#then we forcefully kill any mysqld process just in case
sudo killall -9 mysqld mysqld_safe;........
Yes you have that right, the network service in RHEL8 / CentOS 8 / Rocky Linux / Alma Linux no longer exists. So there is no more systemctl restart network
You can restart NetworkManager but it doesn't have the same effect or ifup/ifdown on all interfaces.
Generally if NetworkManager is installed you will want to restart it or it won't apply the settings from ifcfg.
systemctl restart NetworkManager
To repl........
sudo vi /etc/lightdm/lightdm.conf.d/70-linuxmint.conf
Change this:
[SeatDefaults]
user-session=mate
allow-guest=false
To this:
[SeatDefaults]
user-session=mate
allow-guest=false
greeter-hide-users=true
greeter-show-manual-login=true
To see and apply your changes just restart light........
This is a gotcha but be aware sometimes iptables may be active and loaded by default.
Also make sure you don't just disable firewalld but also stop it otherwise it will still block stuff:
systemctl stop firewalld
If the above is not the issue then it is possible iptables is running and blocking stuff too, so you'll need to stop iptables.
So in addition to opening firewalld or disabling it, you would need to disable iptables........
mysql reset root password.
Oops I can't remember my MySQL root password!
[root@centos7test etc]# mysql -u root -p
Enter password:
ERROR 1045 (28000): Access denied for user 'root'@'localhost' (using password: YES)
First we need to stop mariadb:
systemctl stop mariadb
Now we need to restart it with skip-grant-tables whic........
yum -y install mariadb-server
systemctl start mariadb
mysql_secure_installation
Now we need to secure our install and set the MariaDB root password:
The lines you need to act on are marked in bold shown with the answer you need.
mysql_secure_installation
NOTE: RUNNING ALL PARTS OF THIS SCRIPT IS RECOMMENDED FOR ALL MariaDB
SER........
This problem has been around forever, Linux seems to think it is fine to use the r8169 driver for an r8168 NIC but this often causes problems including the link not working at all.
In my case ethttool shows the link up and detected but it simply does not work especially on a laptop that has been resumed from suspension. Sometimes it takes several minutes for it to work or to unplug and replug the ethernet.
Here is the solution:
Install th........
Use fdisk on your USB drive to create a bootable NTFS partition (in my case /dev/sdb):
sudo fdisk /dev/sdb
Welcome to fdisk (util-linux 2.27.1).
Changes will remain in memory only, until you decide to write them.
Be careful before using the write command.
Command (m for help): n
Partition type
p primary (0 primary, 0 extended, 4 free)........
A lot of times busy servers will have this issue and you cannot even force kill -9 the apachectl or httpd process:
[root@apachebox stats]# ps aux|grep httpd
root 1547 0.0 0.2 495452 32396 ? Ds Sep08 3:23 /usr/sbin/httpd
root 3543 0.0 0.0 6448 724 pts/1 S+ 13:11&nbs........
Oct 18 11:06:46 server systemd[529]: rc-local.service: Failed at step EXEC spawning /etc/rc.local: Exec format error
Oct 18 11:06:46 server systemd[1]: rc-local.service: Control process exited, code=exited status=203
Oct 18 11:06:46 server systemd[1]: Failed to start /etc/rc.local Compatibility.
Oct 18 11:06:46 server systemd[1]: rc-local.service: Unit entered failed state.
Oct 18 11:06:46 server systemd[1]: rc-local.service: Failed with result 'exit-code'.........
Adjust to suit your needs. Currently this would kill any whois process running for more than 30 seconds or more than 1 minute.
Add it as a cronjob. The motivation is that some commands have no timeout and just end up using up CPU and memory for no reason while never exiting to free resources.
#!/bin/bash
IFS=$(echo -en "nb")
for pid in `ps aux|grep whois`; do
echo "pid=::$pid::&qu........
This often happens if you are adding a secondary route, especially with Linux source based routing.
ip route add default via 10.10.10.254 table 10
RTNETLINK answers: Network is unreachable
If that happens you will probably find that it is unreachable because your NIC does not have an IP in the 10.10.10.0/24 range so just assign an IP in that range to your NIC and try again.
eg. ifconfig eth0 10.10.10.254 netmask 255.255.255.0 up........
yum install iptables-services
systemctl enable iptables
service iptables save
iptables: Saving firewall rules to /etc/sysconfig/iptables:[ OK ]........
In Centos 7 tftpd will not work with selinux. Clients will not be able to connect and this is all you'll see in the log (then nothing more):
Sep 18 14:39:15 localhost xinetd[4327]: START: tftp pid=4331 from=192.168.1.65
On the client/computer side you will see this:
TFTP.
PXE-M0F: Exiting Intel Boot Agent
Basically the client is being instantly connected and bloc........
Having a network bridge allows you to bridge traffic under multiple devices so they can talk natively without using any special routing, iptables/firewall or other trickery.
To create your bridge you need the bridge-utils package for brctl and if you want to do things like bridge VMs that run on a tap device you will need the uml-utilities which provides "tunctl".
1.) Install the utilities to make our bridge
sudo apt-get i........
I don't consider a lot of these "extra" kernel modules "nice to have" as they often contain drivers for essential items like your soundcard, your NIC and many other devices that may not work. Sometimes you may find that "sound" or "ethernet" worked before a kernel/OS upgrade and now in the new version they don't. Often it will be because you need to install the "extra" kernel modules.
One other weird thing is that sometimes........
If you've just installed VBox and it is not starting or working, the most common problem is usually that you don't have your kernel source installed, which means there is no kernel driver for vbox so it can't work.
You may get an error that says "Kernel driver not installed" in your Virtualbox.
So the first thing you should do is install your kernel source by running this:
sudo apt-get install linux-headers-`uname -r`........
Install Errors on Version 12:
This error happened on QEMU emulator version 2.11.1 pve-qemu-kvm_2.11.1-5
on Proxmox/Debian but installing on QEMU.12 on Centos 6 did not produce the error.
*Update it is not related to the OS or QEMU version. This happened in Centos 6 too after a second install.
What really causes this even though you successfully install........
If you get error messages like this it is usually because /var/run/sshd does not exist.
root@userbox:/# service sshd status
● ssh.service - OpenBSD Secure Shell server
Loaded: loaded (/lib/systemd/system/ssh.service; enabled; vendor preset: enab
Active: failed (Result: start-limit-hit) since Wed 2019-04-10 02:24:44 EDT; 1
Process: 511 ExecStartPre=/usr/sbin/sshd -t (code=exited, status=255)........
It is almost as intuitive as we would like it is just a *.
So literally:
*INA 127.0.0.1
Complete working bind zonefile below:
$TTL 86400
@ IN SOA ns.rtt.ca. ns2.rtt.ca. (
1247605715; Serial
&n........
The strange thing is that usually the first install or two will work on any new machine but then it suddenly won't. I had this experience on QEMU 2.13 on a different machine. There is something finicky or buggy about the CUCM installer even when choosing the same virtual hardware specs.
qemu-kvm command:
/usr/libexec/qemu-kvm -version
QEMU PC emulator version 0.12.1 (qemu-kvm-0.12.1.2-2.506.el6_10.1), Copyright (c) 2003-2008 Fabrice Bellard
........
This will find all tap devices and try deleting all of them. Of course don't run this if there is a chance an unused tap device is necessary and would not be created by the script ro application using it.
for tap in `ifconfig -a|grep tap[0-255]|awk '{print $1}'`; do
tunctl -d $tap
done........
Pass QEMU this flag:
-soundhw ac97
Or you could use (for a Ensoniq soundcard):
-soundhw es1370
However on some machines I get this error:
pulseaudio: pa_simple_new for capture failed
pulseaudio: Reason: Connection terminated
pulseaudio: pa_simple_new for capture failed
pulseaudio: Reason: Connection terminated
audio: Failed to create voice `ac9........
WARNING: Image format was not specified for '/mnt/space/cucm12.img' and probing guessed raw.
Automatically detecting the format is dangerous for raw images, write operations on block 0 will be restricted.
Specify the 'raw' format explicitly to remove the restrictions.
#you should manually specify the format
q........
For some reason, perhaps you don't want to run a daemon or let Letsencrypt have access to your production server.
There is a way to use it like a normal CSR/CA setup in manual mode.
./letsencrypt-auto certonly --manual -d realtechtalk.com - www.realtechtalk.com
Eventually you will get prompted to create a certain path and file with certain data:
Create a file containing just this data:
Casdfasfadsfsad........
In most of the Cisco router IOS I find the ports like ge0/0 ge0/1 and ge0/2 or whatever your ports are down. They will not even give you a link light. So one of the first tasks should be getting the port you are working with up.
In my case the first goal is often connectivity with the LAN and WAN.
LAN = your local area network (eg. in the office/home )
WAN= your ISP/public internet (eg. fiber/cable/dsl/ethernet).........
Idid a systemctl restart networking and it broke Proxmox VM connectivity!
#proxmox is the problem after restarting the network the tap devices go to disabled state
[2230884.919905] vmbr0: port 7(tap118i0) entered disabled state
[2230884.948864] vmbr0: port 8(tap122i0) entered disabled state
[2230884.972748] vmbr0: port 6(tap119i0) entered disabled state
[2230885.004745] vmbr0: port 5(tap117i0) entered disabled state
[2230885.03673........
This is not about systemd/systemctl and not about "onboot" so there's no rc.local trick here but it's the GUI/Gnome etc when a user logs in that a command is launched.
Put this in your home dir
The .config/autostart directory is where Linux Mint/Ubuntu checks for autostart application config files
mkdir -p ~/.config/autostart
Create a new entry/file that starts an application........
./certbot-auto --apache certonly
Saving debug log to /var/log/letsencrypt/letsencrypt.log
Plugins selected: Authenticator apache, Installer apache
No names were found in your configuration files. Please enter in your domain
name(s) (comma and/or space separated) (Enter 'c' to cancel): yourdomain.com
Obtaining a new certificate
Performing the following challenges:
http-01 challenge for yourdomain.com
Cleaning........
In Debian a lot of times SSH disables the root user to login by password by default. This means you will get an authentication failure as if you typed in the wrong password.
The logs also indicate the password is wrong but what is often the case is in the config file
Check /etc/ssh/sshd_config
cat /etc/ssh/sshd_config|grep -i permitrootlogin
Make sure it says:
PermitRootLogin yes
If not change it and restart SSH........
Below are the common errors you'll get with named AKA bind if your time is incorrect.
The simplest solution is to install and run ntpd to correct your system's time (install ntpd if it is not installed)
systemctl start ntpd
systemctl enable ntpd
Dec 20 13:36:16 hostingbox named[2169]: error (no valid DS) resolving 'develop.waxrain.com/A/IN': 14.215.150.17#53........
A lot of people just have a -j DROP to drop all unwanted traffic or traffic not explicitly allowed but there is a better solution if you want real and proper logging:
Here is another example of more advanced iptables rules.
Take an example iptables rules file
-A INPUT -m state --state RELATED,ESTABLISHED -j ACCEPT
-A INPUT -i eth1 -p icmp -j ACCEPT........
Set this in /etc/sysctl.conf
net.ipv6.conf.all.disable_ipv6 = 1
#apply the settings
sudo sysctl -p
........
Do you hate it when your ISPhas old cached records because of a high TTLon the DNS record of the relevant domain? In plain English this means you often can't connect to a site or service because your ISP's DNS servers haven't gotten word of the new IP address (probably because they haven't checked). There are also some that are notorious for ignoring TTL and not updating records for days!
But if you are lucky and smart enough to have your own Linux based DNS se........
Before getting into the output here is my typical experience with SMART, there is what I call a "bad disk" with pending and uncorrectable sectors that cannot be reallocated.
It has caused a kernel panic and system crash repeatedly as we can see from the logs.
But SMART says it has "PASSED" its self assessment. SMART is still useful to me but it is more about looking at Current_Pending_Sector.
Any time I have had anything but 0 for that attribute it........
#to show all
VBoxManage list vms
#show ONLY running vms
VBoxManage list runningvms
VBoxManage storageattach test --storagectl "SATA" --port 0 --device 0 --type hdd --medium iscsi --server 192.168.1.91 --target "iqn.2018-12.local.abcrandom.target:sdb" --initiator "iqn.1982-01.ca.bla.tld:abc123" --t........
systemd is like the service manager for your Centos and other modern Linux distributions (including Debian/Mint/Ubuntu) allows you to enable services, stop them, restart them, check their status and even reboot your system.
The key commands or arguments you will use with systemctl are the following:
Unit Commands:
list-units [PATTERN...] List loaded units
&nbs........
Did you just install the minimal version by accident or want to install the GUI? No need to reinstall just tell yum to do the work for you!
You could actually have both installed and choose one as your preference on demand (although many people prefer GNOME's simplicity).
Step 1.)
Install Gnome and/or KDE.
To install the GNOME Desktop on Centos 7:
yum -y groups install "GNOME Desktop"
To........
#Linux Mint 18.2 how to install gajim .16.9 so you can use OMEMO encryption:
sudo apt-get install python-axolotl python-nbxmpp
wget https://gajim.org/downloads/0.16/gajim-0.16.9.tar.gz
tar -zxvf gajim-0.16.9.tar.gz
cd gajim-0.16.9
./autogen.sh ;make;sudo make install
#if you get this error you need to get a newer python-nbxmpp from here:
gajim
Gajim needs python-nbxmpp >= 0.6.1 to run. Quiting...........
wget https://downloads.linux.hpe.com/repo/spp/rhel/6/x86_64/current/CP017004.scexe
--2018-08-16 05:11:16-- https://downloads.linux.hpe.com/repo/spp/rhel/6/x86_64/current/CP017004.scexe
Resolving downloads.linux.hpe.com (downloads.linux.hpe.com)... 15.249.152.85
Connecting to downloads.linux.hpe.com (downloads.linux.hpe.com)|15.249.152.85|:443... connected.
HTTP request sent, awaiting response... 200 OK
Length: 1525561 (1.5........
sudo apt-get install hwloc-nox
Reading package lists... Done
Building dependency tree
Reading state information... Done
The following NEW packages will be installed:
hwloc-nox
0 upgraded, 1 newly installed, 0 to remove and 530 not upgraded.
Need to get 151 kB of archives.
After this operation, 453 kB of additional disk space will be used.
Get:1 http://archive.ubuntu.com/ubunt........
An error occurred during a connection to some-ip-or-domain. SSL peer reports incorrect Message Authentication Code. Error code: SSL_ERROR_BAD_MAC_ALERT
The page you are trying to view cannot be shown because the authenticity of the received data could not be verified.
Please contact the website owners to inform them of this problem.
**Solution**
Go to about:config........
You get errors like below and see you have all question marks for the permissions if you go to /run/user/1000/gvfs
If you try to access the mounted share such as anything mounted as gvfs like an SSH share in your file manager you may get an error like this. It generally means an interruption in communication or a fault with gvfsd has caused it.
Solutio........
Aug 13 13:46:33 s2sout2d45040 info Failed in all attempts to connect to proxy.eu.jabber.org
Aug 13 13:46:33 s2sout2d45040 info Sending error replies for 1 queued stanzas because of failed outgoing connection to proxy.eu.jabber.org
No clue why it tries to use a proxy not explicitly specified. This could be because the proxy specified for the domain fails when someone is trying to se........
[root@localhost:~]
BootModuleConfig.sh echo host-ind nfcd........
yes it does create its own json
============================================
cat /tmp/vcsaUiInstaller/ovftool-20180809-175238948-20180809-175603497.log |grep -i json
2018-08-09T17:56:04.238-07:00 verbose OVFTool[30966] [Originator@6876 sub=Default] Manifest file entry: SHA1(VMware-vCenter-Server-Appliance-6.7.0.12000-8832884_OVF10-file1.json) = 1deb658c724767697587d5909c4051c01813e6a1
--> ........
sudo apt-get install libcurl4-openssl-dev git build-essential autotools-dev autoconf libcurl3
sudo apt-get install libcurl4-gnutls-dev
git clone https://github.com/wolf9466/cpuminer-multi
sudo apt-get install cmake libpthread-* libmicrohttpd-dev libssl-dev libhwloc-dev
git clone https://github.com/fireice-uk/xmr-stak-cpu.git
make install
cd bin
chmod +x xmr-stak-cpu
./xmr-stak -O xmr........
vzctl stop 4096
Removing stale lock file /vz/lock/4096.lck
Stopping container ...
Child 546213 exited with status 1
^Z
[1]+ Stopped vzctl stop 4096
~]# rm /vz/lock/4096.lck
rm: remove regular file `/vz/lock/4096.lck'? y
~]# vzctl stop 4096
Stopping container ...
Child 546246 exited with status 1........
Server Side Config
1.) First install nfs-utils
yum -y install nfs-utils
2.) Configure nfs share
Create a directory for your NFS share
mkdir /datastore
Create your NFS share in /etc/exports
echo "/datastore 10.220.101.0/24(rw,sync,no_root_squash)" >> /etc/exports
systemctl restart nfs........
Ialready have the caja-image-converter option installed but it shows nothing.
Weirdly enough if you install nemo and nautilus converter it does show and work inside caja:
The solution is to install *-image-converter
sudo apt-get install *-image-converter
Reading package lists... Done
Building dependency tree
Reading state information... Done
Note, selecting 'n........
#mount the VCSA DVD
mount /dev/sr0 /mnt/cd
#alternatively you could mount the iso directly
mount -o loop vcsa.iso /your/mount/path
#for this purpose we are using the CLI installer on Linux
cd /mnt/cd/vcsa-cli-installer/lin64
#no it's not going to be that easy you can't just run vcsa-deploy like that you need to use a template or configured .json file
./vcsa-deploy
Usage: vcsa-deploy [-h] [--version] [--supported-deploymen........
10/07/2018 03:05:14 PM [IPv4] Got connection from client10.10.25.1
10/07/2018 03:05:14 PM other clients:
10/07/2018 03:05:14 PM Client Protocol Version 3.7
10/07/2018 03:05:14 PM Advertising security type 18
10/07/2018 03:05:14 PM Client returned security type 18
10/07/2018 03:05:14 PM TLS Handshake failed: Could not negotiate a supported cipher suite.
10/07/2018 03:05:14 PM Client10.10.25.1 gone
10/07/2018 03:05:14 PM Statistics:........
This basically means that you are running as non-root and you need to be root to create the tun0 or tap0 device on OpenVPN. You could try sudo or adding the openvpn binary to the list of sudoers.........
Jul 3 22:12:17mailserver postfix/smtpd[6195]: fatal: no SASL authentication mechanisms
Jul 3 22:12:18mailserver postfix/master[4881]: warning: process /usr/libexec/postfix/smtpd pid 6195 exit status 1
Jul 3 22:12:18mailserver postfix/master[4881]: warning: /usr/libexec/postfix/smtpd: bad command startup -- throttling
This only ever happens in my experience when the authentication method is actually Dovecot. Usually the problem........
Centos when copying old files and restarting it seems load everything fine and then says [FAILED] with no log or other message.
service restart named
named [FAILED]
Check more thoroughly you may have missed the error if you have lots of zones!
service named restart|grep error
zone 1.168.192.in-addr.arpa/IN: not loaded due to errors.
zone 2.168.192.in-addr.arpa/IN: no........
This happens because Dovecot limits the maximum IMAPconnections per IPto just 10. This may be fine for a single client side IPbut if an entire office or multiple users are behind one IPor a single heavy user is active then you will get bizarre errors in your e-mail clients such as "Password Incorrect" or similar in Thunderbird. It won't be obvious on the client side as to what the problem is and they will probably just think the server is misconfi........
This is not the normal "black screen"issue and I was shocked to eventually find out why. The normal advice of reconfiguring Xorg didn't work. Even booting into "Recovery Mode" did not help.
Here is the short end of the stick that fixed it:
sudo apt-get install mdm mate-desktop-environment
Yes you got it right, mdm and the mate-desktop-environment / gnome were somehow uninstalled. This must be whe........
It is well known hackers, the NSA, CIA and other groups have created malware to secretly turn on your webcam and microphone on your phone, tv etc.. But fortunately on our computers and laptops we have some options.
Most webcams use the "uvcvideo" kernel module / driver. You can disable this in two ways on boot. I recommend both just as a failsafe.
Disable it on rc.local once your system boots automatically
Add the followi........
Error: Unable to apply new quota values: quota not running
Container start failed (try to check kernel messages, e.g. "dmesg | tail")
Killing container ...
Container was stopped
Error: Unable to apply new quota values: quota not running
Can't umount /vz/private/123123: Invalid argument
[root@rtt 123123]# vzquota on 123123
vzquota : (error) Can't open quota file for id 123123, maybe you need to reinit........
This guide will work for most modern Linux versions like Centos RHEL 7, Debian, Mint, Ubuntu etc...
In Centos 7 the days of editing the "kernel"line and adding "single"are gone. On top of that sometimes after a new install passwords do not work, maybe you forgot your password or for some other reason you need to break in or fix your system? It could also be because you can't mount your root / or some other /etc/fstab error and many other err........
$title_clean = substr($title,0,-3);
In the above example the last 3 characters will be removed from the string "$title". You can of course have the last X removed by changing -3 to -X........
MySQL will silently truncate a larger INT than capable.
Check MySQL's own documentation here:
As we can see the maximum size of INT (which is the most commonly used) is 2147483647
A lot of coders make this mistake by using very large values such as 9999999999 but it would actually truncate to 2147483647 which is the maximum size of an INT. This is dangerous beca........
PHP Warning: PHP Startup: Unable to load dynamic library '/usr/lib64/php/modules/geoip.so' - /usr/lib64/php/modules/geoip.so: undefined symbol: GeoIP_country_code_by_name_v6 in Unknown on line 0
Remove the GEOIP from PHP:
php71w-pecl-geoip-1.1.1-1.w6.x86_64
PHP Fatal error: PHP Startup: apc_shm_create: shmget(0, 67108864, 914) failed: Invalid argument. It is possible that the........
This just simply outputs what you need a username and password that can be used to authenticate from .htaccess
htpasswd -nb user password
user:Gnb6uE9Lp4gt2
If you want to write it straight to a file
htpasswd -cb /tmp/somefile.pw user password
How To Use This In .htaccess
AuthUserFile /tmp/somefile.pw
AuthName GetLost!!
AuthType B........
The Linux Kernel interpretated a very high volume of real traffic as a DDOS attack so it basically ends up blocking your web server.
possible SYN flooding on ctid 42131, port 80. Sending cookies.
Simple fix edit sysctl values for max_syn_backlog
sysctl -w net.ipv4.tcp_max_syn_backlog=5000
To make them permanent edit /etc/sysctl.conf
echo "net.ipv4.tcp_........
This is important as unfortunately Centos may designate a package obsolete and the replacement breaks everything (eg. you have a config file and the new replacement is not at all compatible with it and it breaks your application).
This is where disabling obsoletes comes into play, it can be done from yum but it doesn't work at the time I find.
yum --setopt=obsoletes=0 install someapp However Ifind it still installs the new app and not the one you ask for........
[Wed Sep 20 15:34:44 2017] [notice] suEXEC mechanism enabled (wrapper: /usr/sbin/suexec)
[Wed Sep 20 15:34:44 2017] [error] Init: Unable to read server certificate from file /www/ssl-certs/server.crt
[Wed Sep 20 15:34:44 2017] [error] SSL Library Error: 218529960 error:0D0680A8:asn1 encoding routines:ASN1_CHECK_TLEN:wrong tag
[Wed Sep 20 15:34:44 2017] [error] SSL Library Error: 218595386 error:0D07803A:asn1 encoding routines:ASN1_ITEM_EX_D2I:nested asn1 error........
This through me for a loop when I would do a cp -rf or mv -f nothing would get overwritten even if piping y or yes to the command.
Type alias and you'll see why:
alias cp='cp -i'
alias l.='ls -d .* --color=auto'
alias ll='ls -l --color=auto'
alias ls='ls --color=auto'
alias mv='mv -i'
alias rm='rm -i'
The -i is a safeguard against messing things up but however does mess things up worse when you know what........
The code may lead you to believe you have an incompatible template but if you are not trying to use an old template currently that is not the issue. I actually deleted all 3.x style templates to make sure.
What the issue is, is old plugins that are not compatible but Vbulletin does not seem to account for this except that you'll see a fatal PHPerror. You should disable all plugins and then enable one by one until you find the one that is causing the issue.
&........
When using the .sh script the rendering doesn't work after an upgrade of related packages to kdenlive.
kdenlive (kdenlive:amd64 (4:17.04.1+git201705191233~ubuntu16.04.1)) with affine or composite transitions was fine but is now broken during the time of transition it is just a white screen.
The previous version was fine:
kdenlive:amd64 (4:17.04.1+git201705191233~ubuntu16.04.1
But now I can't find it or install it:........
Solution:
Aptitude is very smart and fixed the issues it was because of nvidia cuda and opencl and nothing else suggested or hinted this using apt
sudo aptitude install wine
The following NEW packages will be installed:
ocl-icd-libopencl1{ab} ocl-icd-libopencl1:i386{ab} wine wine1.6
wine1.6-amd64{a} wine1.6-i386:i386{a}
The following packages will be REMOVED:........
When things go wrong your video is basically unplayable or the first video plays fine and then freezes when moving on to the next. Generally if both videos weren't produced with the exact 100% same settings you will have issues. You can try the basic concat but it often won't work right.
Solution for me:
My example uses 3 videos in total so "n=3" and a=1 to include audio.
ffmpeg -threads 12 -i file1.mp4 -........
#if you have nvidia make sure you install the nvidia-cuda-toolkit so hardware acceleration can be used
wget http://ffmpeg.org/releases/ffmpeg-3.3.2.tar.bz2
tar -jxvf ffmpeg-3.3.2.tar.bz2
cd ffmpeg-3.3.2/
./configure --disable-yasm
install prefix /usr/local
source path ........
This container won't start after exhausting its memory. There are no relevant or helpful messages in dmesg or vzctl.log as well. Standard troubleshooting such as disabling PPP etc has not helped.
2017-07-06T23:33:29-0400 vzctl : CT 888171 : Locked by: pid 166029, cmdline vzctl start 888171
2017-07-06T23:33:29-0400 vzctl : CT 888171 : Container already locked
2017-07-06T23:33:29-0400 vzctl : CT 888171 : Container was stopped
2017-07........
I am using a GTX 1060 but replace the download for the driver with the correct/current version for your particular card by visiting: http://www.nvidia.com/Download/index.aspx?lang=en-us
yum install automake curl openssl-devel libcurl-devel gcc gcc-c++
yum -y install kernel-devel-`uname -r`
yum -y install unzip
#the........
When running cudaminer once it tries to initialize the card the entire screen freezes. The computer itself is still running but the Xorg is done for, you cannot even switch to another console window and must reboot (even an mdm or Xorg restart does not help).
At first cudaminer will give you these errors:
stratrum_recv_line failed
...retry after 15 seconds
GPU #0: Geforce 210 with compute ca........
Jun 1 15:45:42 videoeditor-desktop org.mate.panel.applet.MintMenuAppletFactory[1882]: project_data:INFO Missing folder chosen by user:
Jun 1 15:45:42 videoeditor-desktop org.mate.panel.applet.MintMenuAppletFactory[1882]: project_data:INFO Removed missing file: MAH02949.MP4
Jun 1 15:45:57 videoeditor-desktop org.mate.panel.applet.MintMenuAppletFactory[1882]: ui_util:WARNING Icon theme media-playback-start not found. Will use backup........
Based on this tutorial: http://www.linuxjournal.com/content/overlay-images-video-using-mplayer-and-mencoder
mencoder -oac pcm -ovc raw -vf bmovl=0:0:tfifo -o $output $file
vf_bmovl: Unknown command: ''. Ignoring. ........
apachectl -l
Compiled in modules:
core.c
prefork.c
http_core.c
mod_so.c
It is "prefork.c" so in httpd.conf these settings are what you would use (if you use worker.c it won't have any impact):
StartServers 2
MinSpareServers 5
MaxSpareServers&nb........
espeak - is horrible and sounds very old and robotic
echo "hello there"|espeak
#don't know how to use
mbrola and plugins
cicero
jovie just seems to be a graphical interface to espeak
There is also sbreader/sapi
Google's Text To Speech Works Quite Well
#!/bin/bash
say() { local IFS=+;/usr/bin/mplayer -ao alsa -really-quiet -noconsolec........
This error is commonly due to Java security or TLS settings but there is a second issue with forwarded ports that also causes it.
1. Java Security/TLS Settings issue:
This article has the solution to change them all in Linux automatically
2. Port Forwarding Issue if your Avocent DSR is behind NAT/private IP........
whois in Linux is incredibly out of date and does not seem to recognize most new TLDs domains, but there is a quick and easy tip/hack/tweak for this.
An example of new TLD's site as .review .site .club
whois somesite.club
No whois server is known for this kind of object.
bash to the rescue
Now I did try to apply this in .bashrc but DONOT! Ithink the * wil........
In short the solution is just to use vgremove for the actual /dev/mapper device:
vgremove /dev/mapper/backups-backuplv
box mnt # mdadm --manage /dev/md8 --stop
mdadm: Cannot get exclusive access to /dev/md8:Perhaps a running process, mounted filesystem or active volume group?
box mnt # lv
lvchange lvconvert lvcreate l........
This was a surprising bug but I unplugged all drives for an array md127. At first it was just 1 drive and mdadm seemed to notice this. I unplugged the second drive taking the array offline but mdadm did not realize it was offline and still showed a non-existent disk as being part of it. This created problems trying to unmount it or even to stop this array with mdadm freezing.
As for how to fix it I can only think of making sure you are not in a mounted path of........
[Thu Jan 26 14:13:31 2017] [notice] caught SIGTERM, shutting down
[Thu Jan 26 14:14:00 2017] [notice] suEXEC mechanism enabled (wrapper: /usr/sbin/suexec)
[Thu Jan 26 14:14:00 2017] [error] Server certificate is expired: 'Server-Cert'
[Thu Jan 26 14:14:00 2017] [notice] SSL FIPS mode disabled
[Thu Jan 26 14:14:07 2017] [notice] suEXEC mechanism enabled (wrapper: /usr/sbin/suexec)
[Thu Jan 26 14:14:07 2017] [error] Server certificate is expired: 'Server-Ce........
Many users still are not aware but simply patching OpenSSL does not secure you against many known and easy to exploit attacks that will render your encryption useless by an attacker.
Use the following setings in /etc/httpd/conf.d/ssl.conf
SSLCipherSuite "EECDH+ECDSA+AESGCM EECDH+aRSA+AESGCM EECDH+ECDSA+SHA384 EECDH+ECDSA+SHA256 EECDH+aRSA+SHA384 EECDH+aRSA+SHA256 EECDH EDH+aRSA !CAMELLIA !SEED !3DES !RC4 !aNULL !eNULL !LOW !MD5 !EXP !PSK !........
PHP Fatal error: PHP Startup: apc_shm_create: shmget(0, 67108864, 914) failed: Invalid argument. It is possible that the chosen SHM segment size is higher than the operation system allows. Linux has usually a default limit of 32MB per segment. in Unknown on line 0
PHP Fatal error: PHP Startup: apc_shm_attach: shmat failed: in Unknown on line 0
This error is not at all fun because it actually prevents Apache/httpd from starting or working at all. It will........
iptables -t nat -A OUTPUT -m addrtype --src-type LOCAL --dst-type LOCAL -p tcp --dport 3306 -j DNAT --to-destination ip.ip.ip.ip
iptables -t nat -A POSTROUTING -m addrtype --src-type LOCAL --dst-type UNICAST -j MASQUERADE
sysctl -w net.ipv4.conf.all.route_localnet=1
Make sure you substitute "ip.ip.ip.ip" for your real public IP and also the "--dport 3306" for the port you want to forward.
Finally run the sysctl command and........
forcedeth 0000:00:08.0: irq 25 for MSI/MSI-X
forcedeth 0000:00:08.0: eth0: MSI enabled
forcedeth 0000:00:08.0: eth0: no link during initialization
ADDRCONF(NETDEV_UP): eth0: link is not ready
forcedeth 0000:00:08.0: eth0: link up
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Dec 1 18:21:32 box15 kernel: forcedeth: Reverse Engineered nForce ethernet driver. Version 0.64.
Dec 1 18:21:32 box15 kernel........
The file ipupdate.txt should look like this:
ip.ip.ip.ip ctid
while read -r; do
ip=$REPLY
setip=`echo $ip|awk '{print $1}'`
ctid=`echo $ip|awk '{print $2}'`
echo "vzctl set $ctid --ipadd $setip --save"
vzctl set $ctid --ipadd $setip --save
done < ipupdate.txt........
The only solution after trying many suggestions was to simply restart the "vz" service (definitely not preferable).
Even doing an ifdown and ifup for venet0 did not help.
ifup venet0
Bringing up interface venet0:
Configuring interface venet0:
net.ipv4.conf.venet0.send_redirects = 0
RTNETLINK answers: Network is down
Some errors from log:
CPT ERR: d2dc60........
Tired of checking iotop and seeing that your drbd partition is using 99.99% of io all the time and finding your drbd device performs slow in general?
This is especially an issue in versions of DRBD in the 8.3 tree in particular one documented case is on "8.3.13" but it likely applies to other devices.
The symptoms are that resyncing is fine and normal but any reasonable amount of activity is very slow and lagged and creates a high server load and con........
migrating from an old OpenVZ (Centos 5) to new OpenVZ (Centos 6)
Also if migrating from 32-bit HN to 64-bit your RAM will probably be much bigger than it should be!
16x bigger
eg. 32bit HN:
total used free shared buffers cached
Mem:&nb........
I still cannot understand how this would not be enabled by default and I struggled to find the reason why with manually installing samba etc.. wondering why the option for sharing was not in the menu.
On Linux Mint "MATE" the package is called "caja-share" and on Cinnamon it is called "nemo-share" so edit the below command as necessary:
*Also note that the "samba" package is necessary as it is not inst........
Syncing private
Live migrating container...
Syncing 2nd level quota
11000: invalid option -- F
Usage: vzdqload quotaid [-c file] commands
Loads user/group qouta information from stdin into quota file.
-c file use given quota file
Commands specify what user/group information to load:
-G grace time
-U disk limits........
rm /vz/lock/1200.lck
rm: remove regular file `/vz/lock/1200.lck'? y
vzctl start 1200
Container already locked
vzctl start 1200
Starting container ...
vzquota : (error) can't lock quota file, some quota operations are performing for id 1200
vzquota on failed [7]
vzquota off 1200
vzctl start 1200
vzquota on 1200
root@rttbox ~]# vzquota off 1200
vzquota : (........
kernel: [10186978.064405] TCP: time wait bucket table overflow (CT3)
Varying opinions are out there but in general it seems like the most common culprit is a lack of privvmpages, with a modern OpenVZ system the best way is to set privvmpages as equal to what your RAM is and this has resolved the messages on another system.
If it's truly a TCP issue you can adjust the following parameters:........
I wanted to use Astrachat because it seems to be the only app that has video, pic and file sharing for Jabber butI cannot even connect despite any other client working fine including Xabber and others.
astrachat "Oops.. We can't connect to the account that you provide above. Please recheck your account detail".
Unfortunately to make it worse there doesn't seem to be any error log or more details about the issue.
The jab........
Usually the cause is inexplicable because some things just don't work correctly even when calling all commands by their full path.
Usually adding the following to your crontab file at the top will fix/solve the issue:
SHELL=/bin/sh
PATH=/usr/local/sbin:/usr/local/bin:/sbin:/bin:/usr/sbin:/usr/bin
........
This can happen because port 80 is not open, or your license has expired and/or your IP is out of date and also if the license server itself from cPanel is having issues.
In most cases as long as you have a valid license the following command will solve it:
/usr/local/cpanel/cpkeyclt
Updating cPanel license...Done. Update succeeded.
Building global cache for cpanel...Done
Cannot........
There was a problem importing one of the Python modules
required to run yum. The error leading to this problem was:
No module named yum
Please install a package which provides this module, or
verify that the module is installed correctly.
It's possible that the above module doesn't match the
current version of Python, which is:
2.7.9 (default, Apr 21 2016, 16:51:58)
[GCC 4.4.7 20120313........
openvpn 2.3.10-1.el6 issues
in the .conf
auth-user-pass-verify "passwordcheck $username $password $untrusted_ip" via-env
auth-env does not work correctly in OpenVPN 2.3:
Sat Apr 23 02:30:22 2016 - $username - $untrusted_ip - login failure
But OpenVPN 2.2 does work as expected.
It could be that the specified script automatically receive........
Stopping httpd: [FAILED]
Starting httpd: httpd: Syntax error on line 73 of /etc/httpd/conf/httpd.conf: Cannot load /etc/httpd/modules/mod_file_cache.so into server: /etc/httpd/modules/mod_file_cache.so: cannot open shared obje........
This is a simple fix but not a simple problem and it still doesn't make sense to me.
But in a nutshell if your target proxy server works fast when accessing directly over SSL then this may be your issue.
It seems SSL does not play nicely when the target proxy destination/host has a riduculously long key (such as 8192 bits long). Now this is normally not a problem, in fact the target server could be accessed with hardly any delay directly despite such a long key.........
Auction 262382440107: Cannot connect to URL : SSL connect error: gnutls_handshake() failed: Illegal parameter
Retrying...
esniper encountered a bug. It looks like your esniper version is not
current. You have version 2.28.0, the newest version is 2.31.0.
Please go to http://esniper.sf.net/ and update your copy of esniper.........
Download from here http://www.avagotech.com/products/server-storage/host-bus-adapters/sas-9200-8e#downloads
sudo Installer_P20_for_Linux/sas2flash_linux_i686_x86-64_rel/sas2flash -listall
LSI Corporation SAS2 Flash Utility
Version 20.00.00.00 (2014.09.18)
Copyright (c) 2008-2014 LSI Corporation. All rights reserved
&nbs........
I modified the default to the following for faster local dialing for North American area codes:
(*xx|[3469]11|0|00 [2-9]xxxxxxS0|[2-9]xxxxxxxxxS0|1xxx[2-9]xxxxxxS0|xxxxxxxxxxxx.)
This is what I added to the above: "[2-9]xxxxxxxxxS0" so any 9 digit number is dialed instantly xxx-xxx-xxxx (the S0 at the end makes it dial right away). This makes dialing much quicker and is recommended.
*No........
I have two lines on my PAP2T and the only thing that solved this problem rather instantly was to change the line with the problem to using port 5060 instead of 5061 (so both lines are using port 5600). Note that I am not forwarding either port in my router either.
Some of the symptoms of this problem for me were the following:
No dialtone or it would take several tries.
You answer a call but the phone keeps ringing (takes a few times t........
This command in Debian/Ubuntu/Mint will get everything need installed for most Java based KVM viewers:
sudo apt install icedtea-netx
The following additional packages will be installed:
ca-certificates-java icedtea-netx-common openjdk-8-jre openjdk-8-jre-headless
It seems every other updated version of Java or Icedtea breaks things and I will save the frustration of Java for another post.........
Your server does not support SNI, so all of your SSL websites must use the same SSL certificate. An update to the certificate on an existing SSL website will affect all of your SSL websites, and new SSL websites must use the currently installed certificate.........
I am getting this error:
kernel:[14277.697049] EDAC MC0: UE row 4, channel-a= 0 channel-b= 1 labels "-": (Branch=0 DRAM-Bank=0 RDWR=Read RAS=7048 CAS=0 FATAL Err=0x4 (>Tmid Thermal event with intelligent throttling disabled))
But many people believe this is a bug/false message and the server is running stably.........
vzctl set 2 --devnodes fuse:rw --save
Where "2" is the ctid........
for disk in `fdisk -l|grep "Disk /dev"|awk '{print $2}'|sed s/://g`; do
echo "$disk" && smartctl -d ata -a "$disk" -T permissive|grep -iE 'Device Model:|Serial Number:'
echo "---------------"
done
*Make sure you have smartctl from smartmon tools installed
Sample output:
/dev/sdc
Device Model: ........
How to Increase The Disk and Partition Size in Windows 2022,2019,11,10,8,7 etc.. Server
1, Enter the command prompt
Start -> cmd
2. Start diskpart
diskpart
3. Find the drive that has the wrong size
list volume
4. Select the volume (in this example we use volume 2)
select volume 2
5. Extend the volume........
Here is the scenario you or a client have a remote machine that was installed as a standard/default minimal Centos 6.x machine on a single disk with LVM for whatever reason. Often many people do not know how to install it to a RAID array so it is common to have this problem and why reinstall if you don't need to? In some cases on a remote system you can't easily reinstall without physical or KVM access.
So in this case you add a second physical or disk or already ha........
The solution was to reinstall the vbox dkms package and do a manual modprobe of the modules it makes.
I never sorted out the unable to start due to the USB issue, I did have the guest additions installed but the only way to boot was to change the pointing device from USB to PS2 and then to disable the USB controller (if your pointing device is set as USB, disabling USB will not work because it will re-enable by default when it sees your pointing device is USB, this is w........
First of all this seems to apply to many ONVIF devices
Hard coded IP: 192.168.1.10 (yes not kidding no DHCP!)
00:12:12:9C:C2:00
To view RTSP stream use VLC, or openRTSP or other RTSP capable software:
rtsp://192.168.1.10/user=admin_password=tlJwpbo6_channel=1_stream=0.sdp
user: admin
password: blank
http://ip/Login.htm
Uses Quicktime and is a poor quality picture and slow
Cannot change pass........
sudo apt-get install zoneminder
[sudo] password for one:
Reading package lists... Done
Building dependency tree
Reading state information... Done
The following packages were automatically installed and are no longer required:
libuser-perl python-evince kdebase-apps kwrite unixodbc
libgnomeprint2.2-data python-soappy vgabios python-metacity hddtemp
python-mediaprof........
So the situaton is this, you depend on things being relevant to where your bash script is and to be safe you want it to be dynamic (eg. do not hard code that we switch to /abc/dir but rather detect where script.sh is located).
scriptlocation="$( cd "$( dirname "${BASH_SOURCE[0]}" )" && pwd )"
The path is then contained the the variable "scriptlocation" so you can cd to it in your script etc............
I never did get it working, it is too bad as obfsproxy should really be an option and integrated into the OpenVPN client and server or something similar:
yum -y install python-pip python-devel
No package python-pip available.
#install the EPEL repo
python-pip install obfsproxy
python-pip install obfsproxy
-bash: python-pip: command not found
pip install obfsproxy
&........
yum -y install wget
wget -P /etc/yum.repos.d/ http://ftp.openvz.org/openvz.repo
rpm --import http://ftp.openvz.org/RPM-GPG-Key-OpenVZ
yum -y install vzkernel vzctl
#enable ip_forward
sed -i s/'net.ipv4.ip_forward = 0'/'net.ipv4.ip_forward = 1'/g /etc/sysctl.conf
#all interfaces should not send redirects
echo "net.ipv4.conf.default.send_redirects = 1" >> /etc/sysctl.conf
echo "net.ipv4.co........
If you get that message it means you have inserted the adapter or device incorrectly. In my case the adapter needed to be at the rear end of the pins and it caused this message.
Do not ignore this message as it may appear to work but you will get errors and in reality your chip will not be erased or programmed even if it appears like it is working.........
vzctl set $CTID --devnodes net/tun:rw --capability net_admin:on --save........
yum -y install dvdauthor ffmpeg mjpegtools sox bc
rpm -ivh dvd-slideshow-0.8.4-2.noarch.rpm
Preparing... ########################################### [100%]
1:dvd-slideshow ########################################### [100%]
/usr/bin/dir2slideshow: line 553: bc: command not f........
I'm not sure why I'm getting these but all memory modules are the exact same and all passed memtest successfully although they are ECC. I've heard that ECC RAM can't be tested as well and the kernel seems to indicate they are non-fatl recoverable errors. I wonder if the BIOS has aggressive RAM timing or maybe the controller or motherboard is bad.
[ 12.716515] EDAC MC: Ver: 2.1.0
[ 12.717771] EDAC MC0: Giving out device to........
Thsi is very handy when doing your own kernel development.
-m specifies how much ram (in the example it is 768MB)
-kernel specifies the path to the kernel file
-net tap,ifname=tap1,script=no (the ifname=tap1 is what you need to change and setup manually).
*Run "tunctl -b" to create a tap device and use the one it gives you for ifname=
Enable networking to the outside like this:
*Note we assume that your bridge is br0 i........
I messed up the bootloader by accident on a standard Centos 6.3 install because I turned the /dev/vda1 boot partition into an mdadm raid 1. This was all done correctly aside from one point Ididn't realize was an issue metadata=00.90 is the only thing that will allow you to boot (otherwise grub won't work and you won't boot).
So the next step is rescue mode from a CD right? The problem you will find is that grub does not detect your hard drives, this is Ibelieve is be........
If the below is happening on KVM (a very weird and scary looking error) it's probably because of Windows. This has happened countless times to me where the bootsector on Windows 7/2008 becomes corrupted easily (even by a crash or shutdown).
KVM: unknown exit, hardware reason 0x80000021
kvm_run returned -22
rax 0000000000000010 rbx 0000000000000080 rcx 0000000000000000 rdx 0000000000000080
rsi 000000000025db2a rdi 000000000007db2a rsp 0000000000000200 rbp........
Account Functions -> Change Site's IP Address
Choose the domain and then click "Change"
Choose the new IP
1.) Setup SSL Certificate in cPanel
Click on "SSL/TLS Manager" under the "Security" section.
2.) Under " Private Keys (KEY)"
Click "Generate, view, upload, or delete your private keys."
Choose "Key Size: 4096........
Are you getting the same old error message even though your iptables settings for OpenVZ are correct?
iptables v1.3.5: can't initialize iptables table `nat': Table does not exist (do you need to insmod?)
Perhaps iptables or your kernel needs to be upgraded.
The reason is because in newer vzctl the old way of setting IPTABLES="" in vz.conf is completely deprecated (I spent some time fiddling wondering why my settings were correct but........
if you type Export and see something like this:
declare -x all_proxy="socks://127.0.0.1:22000/"
Most sites assume and tell you to check your .bashrc or /etc/profile /etc/bash.bashrc which may not apply if you've unknowingly or forgot that you setup a proxy from your GUI such as Gnome.
To check in Gnome if you have a permanent proxy do the following:
System -> Settings -> Network Proxy........
It is a permissions issue that is hard to fix.
All but one USB device is greyed out.
I am already a member of "vboxusers"
I have already enabled and disabled USB support for the guest.
I have already reinstalled the latest VBOx guest editions
If running as root it all works fine
Changing........
This is very annoying and also hard for web developers who want to see how things look on Android. You may be fooled into thinking you have an unclosed bracket or incompatible code but this is the "text inflation feature" which I feel should be disabled by default. It works so inconsitently that one block of text will appear small while the other will be huge and is quite annoying.
The solution is simple
Settings ->Display and &q........
The most common solution is to use the /etc/postfix/header_checks but this is a big problem.
Why is header_checks a problem? Because it does it to all mail whether incoming or outgoing and whether authenticated or not. We of course want as much header information for incoming as we can get for many reasons but many organizations want to secure and make their mail clients as secure as possible.
I adapted this solution to the client's custom config, they are configur........
2014-08-12T19:05:55-0400 vzctl : CT 391801 : Unable to start init, probably incorrect template
2014-08-12T19:05:55-0400 vzctl : CT 391801 : Container start failed
This was caused by trying to run a 64-bit template on a 32-bit kernel hostnode which is obviously impossible.
The solution is to use a 32-bit template or upgrade the hostnode to 64-bit.........
vzctl stop ctid
Killing container ...
Child 1033348 exited with status 7
Unable to stop container
vzctl enter ctid
enter into CT 29831 failed
Some have suggested using vzctl stop ctid --fast which does not work.
The only thing that seems to work is restarting the vz service.........
error: Failed to create domain from /home/kvm/kvm101/kvm101.xml
error: cannot open file '/dev//dev/kvmcontainer/kvm101_img': No such file or directory
This is caused by what we consider a quark in SolusVMthat Ihelped a client with.
SolusVMhas as config for the "LVMvolume name" and does not enforce any convention.
Naturally most technical people would use the actual path eg "/dev/kvmcontainer".
However th........
OpenVZ has made vzctl version 4.7 default to using ploop which is a big annoyance. No one wants it otherwise we'd use Xen or KVM.
Make sure to manually specify vzctl 4.6.1 or you will have issues with old scripts breaking since it defaults to using ploop (a single image like Xen/KVM).
Here's a list to old versions of vzctl.........
# first we need a physical volume which we use the pvcreate tool to create
# I create mine on /dev/sdb3
pvcreate /dev/sdb3
dev_is_mpath: failed to get device for 8:19
Physical volume "/dev/sdb3" successfully created
# pvdisplay shows the newly created volume
pvdisplay
"/dev/sdb3" is a new physical volume of "1.35 TiB"
--- NEW Physical volume ---
PV N........
This can happen when you install RPMForge or other repos with the wrong architecture and here's how you fix it (simply uninstalling won't usually fix it):
solution
yum clean all
yum -y install openvpn
Loaded plugins: fastestmirror, presto
Loading mirror speeds from cached hostfile
* base: mirror.its.sfu.ca
* extras: centos.mirror.nexicom.net
* rpmforge: mirror.cpsc.ucalgary.ca
* up........
yum -y install wget
wget -P /etc/yum.repos.d/ http://ftp.openvz.org/openvz.repo
rpm --import http://ftp.openvz.org/RPM-GPG-Key-OpenVZ
yum -y install vzkernel vzctl
After that just reboot and you may also have to enable ip_forward in /etc/sysctl.conf........
nf_conntrack: table full, dropping packet
The above in some cases I've seen is a sign of a DOS attack or can occur if users are using services like torrenting, proxy, VPNetc... Do not take it lightly as the above can knock a server offline if the table becomes full and I've also seen full crashes and kernel panics shortly after.
........
This server has been running for weeks without issue, it's currently only using 1 of 2 CPUs as it is running in the office as a test bed (mainly due to the handle 12 bay storage/great for testing HDDs). The errors below seem to mainly be from AMD CPUs, it's only happened a single time and in the days since Igot that error it hasn't occurrred.
Interestingly enough /proc/cpuinfo still shows all 4 cores of the CPU (Opteron 2373 Quadcore HE) and the functionality doesn't seem........
Example:
basename /var/log/messages
messages
As shown above the "basename" utility gives you the end filename separately.
dirname /var/log/messages
/var/log
As shown above the "dirname" utlity gives you just the utility even if you pass it a specific file.
The above two utilities are very helpful in Bash scripting when working with files and directories co........
./configure
./configure: cannot locate gcc 3.x. please install it or specify with --qemu-cc
yum -y install gcc make
./configure
./configure: cannot locate gcc 3.x. please install it or specify with --qemu-cc
yum -y install compat-gcc-*
./configure
Error: Could not find alsa
Make sure to have the alsa libs and headers installed.
yum -y install alsa-lib-devel
./configure........
On the same OS with the same kernels basically I cannot boot FreeBSD installer, I believe the issue is the host CPU.
One host runs an Intel and works, while an Opteron 2373 does not work despite suggestions from this thread: http://149.20.54.209/showthread.php?t=36761
I've tried cpu options like "kvm64" "Opteron_G3" and none........
Linux box13. 2.6.32-042stab076.5 #1 SMP Mon Mar 18 20:41:34 MSK 2013 x86_64 x86_64 x86_64 GNU/Linux
even setting privvmpages to a specific setting DOES not affect "free -m" in containers.
This is probably a kernel issue
23:36:29 up 159 days, 7:12, 4 users, load average: 0.42, 0.44, 0.33
[root@box13 ~]# free -m
total&n........
This was caused by some weird dmraid setup which kind of takes control of drives even if they're blank/unused.
1. Check the table.
dmsetup table
ddf1_44656c6c202020201000006010281f0b3f5195b77cf86172: 0 3905945600 linear 8:0 0
ddf1_44656c6c202020201000006010281f0b3f5195b77cf86172p3: 0 37124096 linear 253:0 284547072
ddf1_44656c6c202020201000006010281f0b3f5195b77cf86172p2: 0 283496448 linear 253:0 1050624
ddf1_44656c6c2020202010........
Starting container...
vzquota : (error) Quota on syscall for id 42131: No such file or directory
vzquota on failed [3]
Solution
cd /var/vzquota
mv quota.42131 quota.42131-disable
vzctl start 42131
Starting container...
Initializing quota ...
Container is mounted
Adding IP address(es):
Setting CPU units: 1000
Container start in progress...
........
Iread this article and still don't understand the issue.
If I understand correctly the client negotiates after the first SSLconnection and then gets the correct hostname and thus correct certificate.
http://wiki.apache.org/httpd/NameBasedSSLVHostsWithSNI
To their credit I know I'm not using SNIbecuase Iget this message in the Apache log :)
[warn] Init: You should not use name-based virtual hosts in conjunction with SSL!!
B........
/scripts/phpextensionmgr install PHPSuHosin
Updating md5sum list
Fetching http://httpupdate.cpanel.net/cpanelsync/easy/targz.yaml (connected:0).......(request attempt 1/12)...Resolving httpupdate.cpanel.net...(resolve attempt 1/65)...
Fetching http://httpupdate.cpanel.net/mirror_addr_list (connected:0).......(request attempt 1/3)......connecting to 74.50.120.123...@74.50.120.123......connected......receiving...100%......request success......Done........
LSi Megaraid
At first it was configured as a RAID 0, then I deleted the Virtual Disk Group.
I thought both drives would be shown and detected in Linux as sda and sdb but it actually shows nothing.
To make them work you have to hit Ctrl+R before the system boots (when prompted) and create a Virtual Disk Group. In my case I created each one as RAID 0 (with a single drive only) as I just wanted JBOD but there is no such option or default in these Dell Pe........
Bash weird variable whitespace missing
var=`cat tlds.csv|grep .ca,`
# echo "var=:$var:"
:ar=:.ca,Canada
Why is the v missing in the last line?
It should be
:var=:.ca,Canada
instead of
:ar=:.ca,Canada
I noticed a problem with the file with doing a "cat -v" on it.
Here's the issue, the file contains carat M ^M:
.vg,British Virgin Island........
This is basically URL decoding to the decimal code but nothing in PHPworks how you'd expect it.
Here are online tools to verify and check your work, it's important when querying databases with non-English characters:
http://yehg.net/encoding/index.php#
http://meyerweb.com/eric/tools/dencoder/
http://www.codetable.net/decimal/65398
Japanese:
http://symbolcodes.tlt.psu.edu/bylanguage/japanesechartkatakana.html
Charat code for PHP:........
mkdir: cannot create directory 'test': Disk quota exceeded
You are out of inodes usually:
df -i
Filesystem Inodes IUsed IFree IUse% Mounted on
/dev/simfs 200000 200000 0 100% /
none ........
Another new drive bad from the start:
Jun 2 15:14:18 one-desktop kernel: [15895.386779] ata2.00: exception Emask 0x50 SAct 0x1 SErr 0x280900 action 0x6 frozen
Jun 2 15:14:18 one-desktop kernel: [15895.386782] ata2.00: irq_stat 0x08000000, interface fatal error
Jun 2 15:14:18 one-desktop kernel: [15895.386784] ata2: SError: { UnrecovData HostInt 10B8B BadCRC }
Jun 2 15:14:18 one-desktop kernel: [15895.386788] ata2.00: cmd 60/0........
Container is currently mounted (umount first)
The container is stuck in the "mounted" state, you must manually start it to get it out of that state (there is no umount option as implied by OpenVZ vzctl).........
Have you ever unplugged the wrong drive and then had to rebuild the entire array? It may not be a big deal in some ways but it does make your system vulnerable until the rebuild is done.
Many distros often enable the "bitmap" feature and this basically keeps track of what parts need to be resynced in the case of a temporary removal of a drive from the array, this way it only needs to sync what has changed.
To enable bitmap to speed up rebuilds and sync........
This is just trying to read 5GB off the drive with dd and the drive initially tested ok but shortly after I wondered why I was seeing 2MB/s read speeds. Notice the "current_pending_sector", anytime I've seen it at anything above 0 even with no other bad fields/attributes, it means the drive is bad.
ata1.00: exception Emask 0x0 SAct 0x3 SErr 0x0 action 0x0
ata1.00: irq_stat 0x40000008
ata1.00: failed command: READ FPDMA QUEUED
ata1.00: cmd 60/00:00:........
mysqldump: Couldn't execute 'show create table `general_log`': SHOW command denied to user 'user'@'localhost' for table 'general_log' (1142)
One of my clients almost found out the hard way, here is an unlikely situation that happened.
1.) Years ago the client had another VPS to which they backed up a BLOG nightly to an .sql file, what they forgot is that the file also contained all databases (they used the --all-databases option but forgot). So imagi........
This is something many people and especially businesses worry about, or at least they should. Before throwing away a hard drive, returning a hard drive, or especially Warrantying/RMAing it, you should wipe the drive.
Linux provides the "shred" and "dd" utlities which work quite well. It seems even a single pass is good enough but by default shred will do 3 passes.
Here's an example of using shred in Linux (I use a custom made distribution from........
If you make changes to /etc/sysctl.conf (which are permanent and not lost during reboot) but want them to apply with rebooting just use the following command:
sysctl -p
After that your changes will be enabled.........
smartctl -a /dev/sda
smartctl version 5.36 [i686-pc-linux-gnu] Copyright (C) 2002-6 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
Device: ATA WDC WD1600YS-01S Version: 20.0
Serial number: WD-WCAP03024940
Device type: disk
Local Time is: Mon Apr 29 21:40:07 2013 PDT
Device does not support SMART
Error Counter logging not supported........
Client Log
OpenSSH_4.3p2, OpenSSL 0.9.8e-fips-rhel5 01 Jul 2008
debug1: Reading configuration data /etc/ssh/ssh_config
debug1: Applying options for *
debug1: Connecting to 192.168.1.253 [192.168.1.253] port 22.
debug1: Connection established.
debug1: permanently_set_uid: 0/0
debug1: identity file /root/.ssh/identity type -1
debug1: identity file /root/.ssh/id_rsa type 1
debug1: identity file /root/.ssh/id_d........
Kernel panic - not syncing: Attempted to kill init!
Pid: 1,comm: init Tained: G I------------- 2.6.32-358.el6.x86_64 #1
Call Trace:
[] ? panic+0xa0/0x16f
[] ? do_exit+0x862/0x870
[] ? fput+0x25/0x30
[] ? do_group_exit+0x58/0xd0
[] ? sys_exit_........
This is a handy link and list of all the relevant Directadmin log files and related servers.
http://help.directadmin.com/item.php?id=11
DirectAdmin:
/var/log/directadmin/error.log
/var/log/directadmin/errortaskq.log
/var/log/directadmin/system.log
/var/log/directadmin/security.log
Apache:........
vzquota : (warning) block_hard_limit [102] < block_current_usage [520824]
This is because your disk usage of the container exceeds the quota.
Eg. once on a test container I had accidentally set it to 32MB yet the OS took about 600MB.
Just set the quota to something bigger than the currently used space to solve it.
vzctl set 3891 --diskspace 5G:5G --save........
Here's a proven example of what a bad hard drive can do, it was technically functioning OKin a RAID array but the system became extremely low and the load become high and IOWAIT was even higher and I always thought it was a bad application. The truth is that this failing 1TBHitachi has slowly gotten worse and caused huge slowdowns, (eg. 100% load on Thunderbird waiting for e-mails to load etc..). After swapping it out, tabs change instantly, emails are not lagged, and........
Here's what SMART tells me the serial number is:
=== START OF INFORMATION SECTION ===
Device Model: Hitachi HDS721010CLA332
Serial Number: JP2940HQ3ZY7KH
Firmware Version: JP4OA3EA
User Capacity: 1,000,204,886,016 bytes
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 8
ATA Standard is:&nb........
02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03)
For whatever reason it seems the r8169 driver that ships and has shipped with most Linux distros for years is still flawed and does not work properly on these cards, causing 100mbit connectivity when it should be 1gbit and even worse, causing random network dropouts. The r8169 driver in Linux kernels is simply not meant to be used on th........
Tools -> Options -> OpenOffice Writer -> Table
Uncheck "Number Recognition"
This will permanently disable it but won't undo the damage it has already done. I spent a long-time fighting with this horrible feature which should be disabled by default.........
This booting error is because the Xen PV guest image uses the Xen kernel, this is not compatible with anything but a host running a Xen kernel.
I did a kpartx -av virtual.img and then it created some partitions that showed up in fdisk.
I mounted it and did a chroot into it and removed the xen kernel and installed a normal kernel but Xen still shows the same kernel in Grub (only the Xen one).
This is strange but it seems like this Xen PV guest has some sort of hidden or........
Let's keep this simple, it's horrible, not only is the picture quality horrible (it's not a big deal) but the keyboard input is an issue. You have to type slowly, lightly and carefully otherwise 1-keystroke could end up being dozens of keystrokes.
It's also a confusing unit for many datacenter techs, I've seen these units hooked up wrong and the instructions themselves aren't clear. I had to resort to shipping one to my office and take my phone pictures of the setup for th........
Here is a quick script that works on most Centos versions to disable the virus/SELinux from blocking basic functionality.
The first echo 0 statement disables SELinux instantly but it will still be enabled on reboot.
The second line disables it permanently.
#!/bin/bash
#disable SELinux Immediately
echo 0 > /selinux/enforce
#disable SELinux Permanently
sed -i 's/SELINUX=enforcing/SELINUX=disabled/g' /etc/selinux/config........
mdadm --manage /dev/md1 --add /dev/sdb1
mdadm: metadata format 00.90 unknown, ignored.
mdadm: metadata format 00.90 unknown, ignored.
mdadm: metadata format 00.90 unknown, ignored.
mdadm: /dev/sdb1 not large enough to join array
md1's first primary member /dev/sda3 has 57394 cylinders while the /dev/sdb1 has 57393 (1 less cylinder) which is why it won't work.
fdisk -l /dev/sda3
Disk /dev/sda3: 47........
ip tunnel add tun3 mode gre remote 192.58.1.5 ttl 64
ioctl: no such device
I solved this on Centos by loading the ip_gre module:
modprobe ip_gre
On Debian I believe it is the "sit" module.........
parted sdc.img
GNU Parted 1.8.8
Using /home/one/sdc.img
Welcome to GNU Parted! Type 'help' to view a list of commands.
(parted) unit&nb........
When trying to delete a tunnel
ip tunnel del tunl0
I get this message:
ioctl: Operation not permitted........
ip_conntrack: table full, dropping packet.
A lot of clients I've seen have this issue, it really seems the default level is way too small. Once this connection tracking table becomes full then packets get dropped which is obviously a bad thing.
One thing to be mindful of though is that 350 bytes of memory are used per entry so there is some justification for not keeping it too high. However, if you have multiple servers running or high traffic daemons........
I backed up everything in the /mnt/sd_card directory thinking that some dataloss could occur for some reason but purposely left my microSDHC unbacked up thinking that "it won't touch that since it's external" and Samsung's and other manufacturers website even say this (that it won't be affected and not to worry etc).
Apparently I was wrong, my microSD was "undetected" and asked to be formatted after the upgrade (there goes 3-months worth of family photos). No........
This may sound silly but there will be conflicts/issues with the default Centos repository so you have to use a third party like remi (I prefer not to do this but it's the only option unless you migrate your sites/data to another server or can stand some downtime-not an option IMHOon a production server).
You may need to upgrade to PHP5.3 to run Joomla or many other reasons.
Your host needs to use PHP 5.2.4 or higher to run this version of Jo........
The best way I could figure out is to use another guest of some sort to do this, while assigning the disk that needs to be resized to the same guest.
So say we have /dev/xvda as the guests drive and we've booted it up.
We also have /dev/xvdb (this is going to be the image/disk to be resized).
In this case it's based on an ext3/4 image.
Run e2fsck on it to ensure there are no filesystem errors.
e2fsck /dev/xvdb........
00:14.2 Audio device: Advanced Micro Devices [AMD] Hudson Azalia Controller (rev 01)
00:01.1 Audio device: Advanced Micro Devices [AMD] nee ATI Device 9902
Backup your also.conf file
cp /usr/share/alsa/alsa.conf /usr/share/alsa/alsa.conf.bk
Change all instances of "card 0" to "card 1" (no need to manually do it, this command below does it all instantly and without fail or error:........
I am running a 64-bit host and was running a 32-bit XPguest which was crawling no matter what I was doing with it,in fact it frequently used 100% CPU power while having no real work load. I experienced with this other guests and wondered why KVM was slow compared to say Xen or Virtualbox.
This is because you need to use the "-cpu" flag.
For a full list of options run:
/usr/libexec/qemu-kvm -cpu ?
x86 ........
VBoxManage modifyhd XP.vdi --resize 15000
VBoxManage modifyhd XP.vdi --resize 15000
0%...10%...20%...30%...40%...50%...60%...70%...80%...90%...100%
That resizes the virtual hard drive image "XP.vdi" to 15000MB instantly.
I doubt this is safe to do while the VM is running and I'm not sure if it would attempt it still but turn the VM off first to be safe.
I also notice in the VBOX GUI that it still shows the orig........
Error: detected vswap CT config but kernel does not support vswap
This means either old kernel or bad config (physpages NOT set to 0:unlimited)
Solution
vzctl set $veid --physpages 0:unlimited --save........
iptables v1.3.5: can't initialize iptables table `nat': Table does not exist (do you need to insmod?)
This solution applies to all other iptables modules/problems for OpenVZ, you'll just need to add them to both lists/lines below if you have modules other than what I have below.
The modules need to be enabled in both iptables and the OpenVZ hostnode itself and then the containers which need it must be restarted.
How To Enable IPTables Modules in OpenVZ........
I searched for days after getting my Galaxy Note and couldn't find a way to do this (at least not without buying programs for either Android/Windows). All I read was ways to sync and import the contacts to GMail but I don't want to use GMail for privacy reasons. GMail/Google steal all of your personal information and use it for whatever purposes they want to and may sell or release it to who knows where (I don't care what their policy says but this stuff happens), just like the default........
Could not display "trash:///".
Error: DBus error org.freedesktop.DBus.Error.NoReply: Did not receive a reply. Possible causes include: the remote application did not send a reply, the message bus security policy blocked the reply, the reply timeout expired, or the network connection was broken.
Please select another viewer and try again.
This happened in Ubuntu but only because I was trying to delete millions of files at once and i........
debug1: An invalid name was supplied
Cannot determine realm for numeric host address
debug1: Local version string SSH-2.0-OpenSSH_4.3p2 Debian-9etch3
debug1: An invalid name was supplied
Cannot determine realm for numeric host address
debug1: An invalid name was supplied
A parameter was malformed
Validation error
Solution, disable auth from the ssh client (this is a client side error)........
I've thought for awhile that Asus has been banking on its years old reputation for quality amongst gamers and enthusiasts and I think I'm right. My Asus VE247H Monitor with a supposed 2MS refresh rate has 1 red/stuck/dead pixel but fortunately it can only be seen on a non-true black picture or against a blue screen.
I have several Asus products and find they're all of fairly poor quality. First of all their motherboards have given me the most issues of any brand, they te........
fdisk -lu VPS.img
last_lba(): I don't know how to handle files with mode 81ed
You must set cylinders.
You can do this from the extra functions menu.
Disk VPS.img: 0 MB, 0 bytes
255 heads, 63 sectors/track, 0 cylinders, total 0 sectors
Units = sectors of 1 * 512 = 512 bytes
Device Boot Start End ........
Stuff like this always happens/breaks after a vzctl update, whether it's new parameters being added or required etc..
File /etc/vz/conf/ve-vps.basic.conf-sample not found: No such file or directory
Fix the value of CONFIGFILE in /etc/vz/vz.conf
Creation of container private area failed
Warning: distribution not specified in CT config, using defaults from /etc/vz/dists/default
WARNING: /etc/vz/conf/4400.conf not found: No such file or directory........
I dread updating the kernel and rebooting to find the Ubuntu graphics aren't working and you have to manually intervene. This is usually because Ubuntu for whatever reason didn't update the drivers you need (eg. the manually compiled Nvidia Kernel driver that MUST be recompiled for each and every kernel update unfortunately).
The most common reason may be that "linux-source" hasn't been installed automatically on my system. I tried to manually reinstall the........
This is one in a series of weird things whichIthought was motherboard related (I RMA'd the motherboard), the RAM tests fine with memtest86 and I used badblocks on both RAID 1 members with no errors and smartctl is happy with them.
Basically the array crashes the kernel a lot and has issues when writing.
[112322.723465] md0: rw=0, want=14958668696, limit=1887460480
[112322.731077] attempt to access beyond end of device
[112322.731087] md........
The normal solution would be as follows:
export DISPLAY=:0.0
/usr/lib/vino/vino-server &
But what happens if that doesn't work? I haven't been able to find much documentation about how to find the list of displays and how their numbering works in Xorg.
Sometimes you'll get this error when trying to restart vino:
Cannot open display:
For some reason my display is not on 0.0........
Within vi if you can't exit /etc/vim/vimrc you can type
:syntax off
And to turn it back on:
:syntax on
Many of us have a dark/black background in our terminal/shell making the default syntax unreadable, the solution is to either turn off syntax highlighting with :syntax off or to enable a special option in /etc/vim/vimrc
Edit /etc/vim/vimrc
The "syntax on" enables the highligh........
netstat is weak and can't show udp connections and most other protocols, use "ss" which is what netstat should have been:
The "-u" switch stands for udp, here's a list of other options:
Usage: ss [ OPTIONS ]
ss [ OPTIONS ] [ FILTER ]
-h, --help this message
-V, --version output ver........
Starting online migration of CT 25000 to 192.168.5.1
Preparing remote node
Initializing remote quota
Syncing private
Live migrating container...
Error: Failed to suspend container
CPT ERR: f68cf000,25000 :foreign process 15755/14731(vzctl) inside CT (e.g. vzctl enter or vzctl exec).
CPT ERR: f68cf000,25000 :suspend is impossible now.
CPT ERR: f68cf000,25000 :foreign process 15755/14731(vzctl) inside CT (e.g. vzctl enter or........
I had a system running a 128MB live CD image with 2.8 gigs of available RAM and the OOM kernel killer went crazy when using dd for more than 8 minutes and kept killing everything. I've read that this is due to a low-memory issue and paging in the kernel and 32-bit systems with lots of RAM.
I even enabled swapspace on my LiveCD and the issue happened 25 minutes into dd rather than 8 minutes, so what gives?
Also no swap space was ever used!
cat /proc/s........
I like dd, although it only reads it, usually a read test of the entire disk will uncover if your hard drive is bad in some parts. This is a good thing to do at least once a month, a lot of times bizarre program behavior, laginess and crashing/unnmounting problems etc.. are due to a failing disc and SMART won't know it or indicate a problem:
We must also remember there's never a guarantee, I've found that ever since we moved to larger and more platters per drive with 1TB drives........
I had a dying drive that smart thought until it totally disappeared was a good drive, and actually all parameters did look fine but this system was causing my system to lockup and other bad behavior:
=== START OF INFORMATION SECTION ===
Device Model: WDC WD20EARS-00MVWB0
Serial Number: WD-WMAZ20139
Firmware Version: 50.0AB50
User Capacity: 2,000,398,934,016 bytes
Device........
CPT ERR: cc4c0800,28000 :Unknown image version: 304. Can't restore.
This happens when you live migrate between OpenVZ servers with different kernels running, at least significantly different by date.
There is no solution except to make sure you're running the same kernels on all machines, or at least not kernels that are much older or different (this is just a guess though, you should ensure all kernels are the same).........
I had one of these shipped and it was not recognized when plugged in, here's what a dead drive looks like (I assume it's teh circuit board which is dead):
ata1: link is slow to respond, please be patient (ready=0)
ata1: softreset failed (device not ready)
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1: link online but device misclassified, retrying
ata1: link is slow to respond, please be patient (ready=0)
ata1: softreset f........
This assumes that you've at least created the correct partition for your DRBD already.
Notice that I am "diskless", that's because either your DRBD partition doesn't exist/has been renamed (eg. sdb becomes sda when sdb dies and you reboot) or because that drive is really actually dead/gone.
*If you need to permanently change the partition/device for your resource be sure to edit /etc/drbd.conf on both hosts and reload the config.
(replace r0 with........
I thought only a faster CPUand SSDwould help but I already have a Quad-Core CPU and it wasn't being maxed out. The actual tests were performed on an AMD-V enabled 128MB dual core VMWare container though.
There is a flag that can be passed to make in order to start multiple threads, by specifying 4 threads I was able to reduce the whole kernel compilation time from scratch by about 50%! (65minutes vs 31minutes!). *Yes I did do a make clean before each co........
This is e-mail notification to warn you that your hostname is setup improperly on your system.
This is an annoying message and bug with Directadmin, my hostname is set correctly, why does it complain?
To get of this message just run this command:
/usr/local/directadmin/scripts/hostname.sh yourhostname.com........
May 6 08:16:57 devbox spamc[16225]: connect to spamd on 127.0.0.1 failed, retrying (#2 of 3): Connection timed out
May 6 08:17:02 devbox spamc[20214]: connect to spamd on 127.0.0.1 failed, retrying (#1 of 3): Connection timed out
spamc[16225]: connect to spamd on 127.0.0.1 failed, retrying (#3 of 3): Connection timed out
First make sure that the spamd service is actually running, this is your spamd (spamassassin server) cannot be reached. In my c........
Virtualbox hang problem
A VM just froze and wouldn't close so I had to force it, but the VBox GUI thinks it's running even when I close it.
I manually killed the related process by doing ps aux|grep VirtualBox and found the PID 6191
I killed it with "kill -kill 6191" but it remains open and as "defunct" so I can't restart it because the GUI freezes when I click on it because it thinks it is running still........
mod_status is a great way to track down the source of high CPU usage and to find what vhost/script is the cause of it.
It gives you a live view of bandwith usage, CPU usage, and memory usage broken down by domain/vhost and script/URI.
Enable mod_status
vi /etc/httpd/conf/httpd.conf
ExtendedStatus On
SetHandler server-status
Order Deny,Allow
Deny from all
All........
yum -y install vnstat
chown nobody.nobody -R /var/lib/vnstat/
#replace venet0 below with your desired interface
sudo -u nobody vnstat -u -i venet0
#edit: vi /etc/sysconfig/vnstat
#VNSTAT_OPTIONS="-i venet0"
# only use the sed below if you are using venet0 instead of eth0 or replace accordingly
sed -i 's/eth0/venet0/g' /etc/sysconfig/vnstat
[root@monitor]# yum install vn........
smartctl -t long /dev/sda (note you can specify short, but it's not as thorough as long of course).
smartctl version 5.38 [i686-pc-linux-gnu] Copyright (C) 2002-8 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF OFFLINE IMMEDIATE AND SELF-TEST SECTION ===
Sending command: "Execute SMART Extended self-test routine immediately in off-line mode".
Drive command "Execute SMART Extended sel........
high IO wait
424 root 39 19 1900 848 552 D 0.0 0.0 0:00.91 updatedb
root 424 0.0 0.0 1900 848 ? DN Mar11 0:00 /usr/bin/updatedb -f sysfs?rootfs?bdev?proc?cpuset?binfmt_misc?debugfs?sockfs?usbfs?pipefs?anon_inodefs?futexfs?tmpfs?inotifyfs?eventp........
There are all kinds of threads and links on the internet, and this seems to be a contentious issue butI don't know why.
95th percentile is either a good deal for some or a big rip off for others, Ijust said it there :)
But the reality is that for MOST people who transfer low amounts of data but burst to higher speeds such as 40mbit+ even for short periods of time, then you'll pay a lot of money to do that.
Basically 95th percentile is an-old archaic method........
find what MPM Apache is using, it will either be using "worker" or "prefork"
apachectl -l
Compiled in modules:
core.c
prefork.c
http_core.c
mod_so.c
In my case it is "prefork"
vi /etc/httpd/conf/httpd.conf
Find the section that looks like this (by default one will normally exist for prefork and for worker, but in my case I only care a........
Centos 5 Postfix and SPAMASSASSIN Tutorial
yum install spamassassin
chkconfig spamassassin on
vi /etc/mail/spamassassin/local.cf
##############
#required_hits 5
#report_safe 0
#rewrite_header Subject [SPAM]
#5 is the least restrictive (means only the most obvious SPAM is caught. 0 is obviously the most restrictive/sensitive and would have lots of false positives
require........
Make sure the module "tun" is loaded on the host.
vzctl set 2000 --devnodes net/tun:rw --save
*Note what's below is what OpenVZ says you need (but I've never had to do it)
vzctl exec 2000 mkdir -p /dev/net
vzctl exec 2000 mknod /dev/net/tun c 10 200
vzctl exec 2000 chmod 600 /dev/net/tun
On the container test the device:
when Something is wrong:........
Convert MBOX Mail files into Maildir using Linux
*You need perl an the TimeDate module
Get the free Perl script mb2md from the project/author's site:
wget http://batleth.sapienti-sat.org/projects/mb2md/mb2md-3.20.pl.gz
gunzip mb2md-3.20.pl.gz
#remember you need timedate or you'll get this error:
./mb2md-3.20.pl
Can't locate........
Dovecot enable SSL (by default it uses an old expired cert if you choose pop3s and imaps as protocols)
===================
Create Cert & Key:
openssl req -new -x509 -nodes -days 1530 -out server.crt -keyout server.key
mkdir /etc/mailssl
chmod 700 /etc/mailssl
cp server.* /etc/mailssl
Edit /etc/dovecot.conf
ssl_cert_file = /etc/mailssl/server.crt
s........
Create Cert & Key:
openssl req -new -x509 -nodes -days 1530 -out server.crt -keyout server.key
mkdir /etc/mailssl
chmod 700 /etc/mailssl
cp server.* /etc/mailssl
Postfix SSL config
Edit /etc/postfix/main.cf:
#SSL stuff
smtpd_tls_cert_file = /etc/mailssl/server.crt
smtpd_tls_key_file = /etc/mailssl/server.key
To make smtps w........
I think this will be useful to others because I have a server that kept crashing mysteriously during intense disk usage/RAID checks. It would only crash during the weekly RAID integrity check.
ThenI noticed during a reboot that not all CPUs were being brought up, as a result this actually creates much higher temperatures with the output I got from sensors, just booting the system produced higher than normal temperatures.
You can imagine that a full blown RAID check........
understanding /etc/aliases
*remember to apply changes you need to run "newaliases" after editing /etc/aliases
one thing I don't get is that it doesn't allow you to specify the whole e-mail address on the left-hand side
eg:
yourfullemail@domain.com: someotheremail@domain.com
postalias: warning: /etc/aliases, line 109: name must be local (if you try the above)
It works more like this:
your........
Openvz problem, it is confusing because it's an inode issue and there is enough free space.
cp: cannot create regular file `forums/memberlist.php': Disk quota exceeded
/dev/simfs 60G 20G 41G 33% /
none 2.0G 4.0K 2.0G 1% /dev........
Jan 16 04:02:03 centosbox syslogd 1.4.1: restart.
Jan 16 04:07:34 centosbox kernel: INFO: task updatedb:20771 blocked for more than 300 seconds.
Jan 16 04:07:34 centosbox kernel: "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
Jan 16 04:07:34 centosbox kernel: updatedb D F78BE050 6476 20771 20766&n........
The normal solution doesn't help or apply here:
ssh -v user@192.168.5.41
OpenSSH_4.3p2 Debian-9etch3, OpenSSL 0.9.8c 05 Sep 2006
debug1: Reading configuration data /etc/ssh/ssh_config
debug1: Applying options for *
debug1: Connecting to 192.168.5.41 [192.168.5.41] port 22.
debug1: Connection established.
debug1: permanently_set_uid: 0/0
debug1: identity file /root/.ssh/identity type -1
debug1: i........
That is pinging to the gateway IP on the same switch, the same IP is pingable externally without any problems which makes me think the switch is fine.
64 bytes from 55.55.55.55: icmp_seq=4 ttl=255 time=1.07 ms
64 bytes from 55.55.55.55: icmp_seq=1 ttl=255 time=3536 ms
64 bytes from 55.55.55.55: icmp_seq=2 ttl=255 time=2536 ms
64 bytes from 55.55.55.55: icmp_seq=3 ttl=255 time=1536 ms
64 bytes from 55.55.55.55: icmp_seq=8 ttl=255 time=1.20 ms
64 by........
I've only used it on Centos, soI thought I'd make a quick Debian guide:
Install the DRBD Package
apt-get install drbd8-utils
Reading package lists... Done
Building dependency tree
Reading state information... Done
The following packages were automatically installed and are no longer required:
libswfdec-0.8-0
Use 'apt-get autoremove' to remove them.
The following........
I wanted to Import/Use a .vmdk hard disk image file from VMWare. Generally you can just "point" VirtualBox to it and use it and it will work but I found an exception.
One of my Centos 4.4 x64 images wouldn't boot. I had two copies, an older one and the newer one. The older one booted as normal (once I changed the VirtualBox driver to IDE from SATA). The newer one stopped at the "GRUB loading" message no matter what I tried.
As far as........
first container would not come up:
Starting CT 2333:
service vz stop
OpenVZ is locked [FAILED]
2010-11-29T23:26:23-0800 vzctl : CT 2333 : Starting container ...
2010-11-29T23:37:21-08........
hdparm -B 255 /dev/sdb
/dev/sdb:
setting Advanced Power Management level to disabled
HDIO_DRIVE_CMD failed: Input/output error
The one thing you can do though is to set hdparm spindown time lower (it doesn't seem to work that well).
-S set standby (spindown) timeout
hdparm -S 251 /dev/sda
/dev/sda:
setti........
Let the numbers speak for themselves, from what I read the Load_Cycle_Count which is very high (more than 500,000/half a million times) is the number of head parks. What a stupid"Green" design and design flaw which will probably mean an early life for the drive.
This is almost as silly as Seagate's new reputation for BSY/poor quality disks since the 7200.11 series.
To make it worse this is also when Western Digital introduced "Advanced Format" o........
After an upgrade wine wouldn't open anything, not even the pre-installed notepad.
There are no wine logs and nothing is mentioned in any standard log file about why.
I finally decided to run wine from the shell and see what's going on:
wine client error:0: version mismatch 398/402.
Your wineserver binary was not upgraded correctly,
or you have an older one somewhere in your PATH.
Or maybe the wrong wineserver is still running?........
Initializing quota ...
Error: Not enough parameters, diskinodes quota not set
vzctl set $veid --diskinodes 90000:91000 --save
New versions of OpenVZ seem to have some strange diskinodes parameter which is required.........
ping test.com
connect: No buffer space available
/var/log/messages
Oct 18 12:21:03 vps kernel: printk: 177 messages suppressed.
Oct 18 12:21:03 vps kernel: Neighbour table overflow.
Solution in /etc/sysctl.conf:
net.ipv4.neigh.default.gc_thresh1 = 4096
net.ipv4.neigh.default.gc_thresh2 = 8192
net.ipv4.neigh.default.gc_thresh3 = 8192
net.ipv4.neigh.default.base_reachab........
This really gives me a bad impression of SolusVM.
I tried the "Central Backup" option and it does not warn that your server gets shutdown instantly in order to do the backup!
Further, there is no way to pause or cancel the backup. Thankfully this is a test/small disk usage VPS but what if someone was running something production with a large filesize?
Ihaven't used QuickBackup but hope that isn't the same thing.
Everyone should be vary car........
2010:09:09-22:22:11: The ip of this machine (xx.xx.xx.xx) does not match the ip in the license file.
Check the value of your ethernet_dev=venet0:0 setting in your /usr/local/directadmin/conf/directadmin.conf file and the output of /sbin/ifconfig
Solution
/usr/local/directadmin/scripts/getLicense.sh........
service vz start
Starting OpenVZ: failed to load module vzmon [FAILED]
vzmon: Unknown symbol ve_snmp_proc_init
vzmon: Unknown symbol addrconf_sysctl_free
vzmon: Unknown symbol ve_ndisc_init
vzmon: Unknown symbol addrconf_ifdown
vzmon: Unknown symbol ip6_frag_cleanup
vzmon: Unknown symbol fini_ve_route6........
service vz start
Starting OpenVZ: failed to load module vzmon [FAILED]
vzmon: Unknown symbol ve_snmp_proc_init
vzmon: Unknown symbol addrconf_sysctl_free
vzmon: Unknown symbol ve_ndisc_init
vzmon: Unknown symbol addrconf_ifdown
vzmon: Unknown symbol ip6_frag_cleanup
vzmon: Unknown symbol fini_ve_route6
........
cd /etc/yum.repos.d
wget http://download.openvz.org/openvz.repo
rpm --import http://download.openvz.org/RPM-GPG-Key-OpenVZ
yum install ovz-kernel-PAE
Now remember to set /etc/sysctl.conf to "net.ipv4.ip_forward = 1"
You can apply the change immediately by running sysctl -w net.ipv4.ip_forward = 1 but remember that you still have to set sysctl.conf
sysctl -p will load and apply any changes to s........
I am a huge fan of Linux and the idea of OpenSource but I've said it many times, there are still hurdles in today in 2010 for Linux as a Desktop. Linux is still intended for servers at its very core. This can be changed succesfully though, as Apple has shown us with Mac OS X based on FreeBSD.
Half of the issue is lack of driver support and the other half is the Linux Kernel and Window Manages, KDE and GNome still both don't cut it (but they're getting closer).
I'll........
smartctl -a -d ata -T permissive --smart=on /dev/sda
-d ata is usually required for most SATA drives or you get an error.
-T permissive is required if it's the first time you are running SMART on this device (it's not enough just to enable SMART in the BIOS)
--smart=on is also required for the first time........
vzmigrate --online dest-host VEIDNO
eg.:
vzmigrate --oneline 192.168.1.55 101
One option I would recommend is "--keep-dst", that way if the migration is interrupted you can still bring the VPS back up on the original host. After the migration is successful you can manually destroy it.
OpenVZ has a good writeup on this including Checkpointing and Restoring etc:........
This error is annoying, in a Virtuozzo KB entry about this ip tables nat problem they say the kernel needs to be ugpraded:
Symptoms
The node runs 2.6.18-x kernel older than 2.6.18-028stab053.10.
NAT module does not work in container, you get "can't initialize iptables table 'nat'" error:
# iptables -t nat........
After installation Directadmin does not work on OpenVZ VPS when browsing http://ip.ip.ip.ip:2222
service directadmin status
directadmin dead but pid file exists
tail /var/log/directadmin/error.log
Check the value of your ethernet_dev=eth0 setting in your /usr/local/directadmin/conf/directadmin.conf file and the output of /sbin/ifconfig
2010:07:10-12:44:01: ioctl can't find........
This is a great way to use your ftp server space, for example on your web hosting account (althoughI believe many hosts don't allow storage like this), but if you have a VPS/Dedicated Server etc.., this would be perfect. Imagine how easy it is to work with an ftp account that you can just mount as a normal partition or directory in Linux, it would be great for backups etc..
Name
curlftpfs - mount a ftp host as a local directory
Synopsis........
I've never understood how to enable and disable services for different run levels in Debian based distros, it's just weird, annoying and doesn't make sense. I much prefer chkconfig from RHEL.
Just install the package called 'rcconf' and be done with it. rcconf makes things easy for you.
apt-get install rcconf
Reading package lists... Done
Building dependency tree
Reading state information... Done........
Basically the two main types of distros are Debian and RHEL/Centos based. I'm just going to give a quick overview of how the configuration of IP interfaces works in Debian/Centos based distros.
*Just one thing to remember, when setting IPs statically you have to manually specify a DNS server in /etc/resolv.conf (since DHCP is what normally does it automatically)
Debian/Ubuntu/Kubuntu/MEPIS
The IP (DHCP &........
I have an md0 arary that my Centos install refers to. I feel this is half the reason why it won't boot anymore.
I saw the initrd for Centos was assembling it as md127 even though it was known as md0.
The reason for this is because I used mdadm --assemble --scan to detect the array on a LiveCD. I had no idea this name would stick (but now I realize the name is permanently stored in the metadata once you mount md127 or whatever random name assemble gives it). W........
The default options for iptables are very basic. Here is what you need to do in order to enable them in OpenVZ.
1.) Add the modules to iptables and restart iptables:
vi /etc/sysconfig/iptables-config
Edit the line as so:
IPTABLES_MODULES="ipt_REJECT ipt_tos ipt_TOS ipt_LOG ip_conntrack ipt_limit ipt_multiport iptable_filter iptable_mangle ipt_TCPMSS ipt_tcpmss ipt_ttl ipt_length ipt_state iptable_nat ip_nat_ftp"
2.........
cat /proc/user_beancounters produces the following:
kmemsize 1861537 5139870 12752512 12752512 26965041
Notice the failcnt "26965041", that is for kmemsize and at first it confused me. The system had enough guaranteed and enough burst RAM available. kmemsize is a variable indepedent of that, but who cars about the explanation right, let's just make thing........
I took an educated guess because it kept happening at the same spot when loading the XP install. I thought it was the hard drive or motherboard.
But it turns out my heavily used but loved NEC 3500 DVD-RW drive was the culprit. After disconnecting it and swapping it for another much beloved Pioneer DVD-RW, everything has gone smoothly.
I never ran into this or many issues because I've hardly used this drive since moving it to another Desktop years ago. I actua........
This is a very simple solution, but most guides out there make you login twice (once to scp the key) and once to put the key in authorized_keys. There's no need for that.
If you don't already have a ~/.ssh/id_rsa.pub just type "ssh-keygen -t rsa" and keep hitting enter until it's done :)
Just use this code to easily enable passwordless login with SSHD
key=`cat ~/.ssh/id_rsa.pub`;ssh user@192.168.5.25 "echo $key >> ~/.ssh/auth........
Not sure what rsync switches/options to use?
rsync -PDrphogtl
The short version would be:
rsync -Pha
I think these are really common sense options to use and probaby should be the default.
Explanation of rsync switches
P = display the progress
D = hybrid of --specials and --devices so all special and device files will be copied as well.
r = recursive (otherwise rsync won't copy files deeper than........
This drive is clearly on the way out, the Kernel knows it but I'm surprised that SMART is not concerned. I didn't blame Seagate for their past issues until now. This hard drive has hardly been used and has not even been powered on for a year according to SMART.
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda 7200.11
Device........
Seagate Inventory/Firmware Check
I heard about this issue a long time ago but never looked into it. I figured I wasn't affected since my 500GB drives were running for so long. I've been using Seagate's since 2002 and to this day all of the drives I have are alive from Seagate.
*Update the bad news is that I realize one of my 500GB's is about to die, it's not even a year old, but is also not affected by the recall according to Seagate!
Seagate Inventory/Firm........
Before we start I take no responsibility for this, you should have a backup and if you make a mistake during this process you could wipe out all of your data. So backup somewhere else before starting this as a precaution, or make sure it's data you could afford to lose.
The RAID 1 Setup (Hardware Wise)
I've already setup my 2 x 1TB (Seagate) drives with identical partitions, make sure your new hard drive (the empty one) is setup like your curr........
I'm really starting to love ImageMagick, I've used it to mass convert/resize family photos with scripts and all kinds of handy things.
Today I just learned that you can create PDF files with it too, say if you have images scanned or anything else it's very simple:
convert *.jpeg output.pdf
You can replace jpg with whatever format your files are in. One thing to remember is that you can specify the order that the images/pages are added to the PDF manu........
The folder I was trying to archive is about 72GB, but much like rsync at about 17GB it chokes because of the filesize. What's with so many common and essential Linux tools having such limitations? I guess it is likely that the authors never wrote their code with the idea that files would be so large but it's still very annoying. It's important to stay on top of these limitations on production servers because I didn't realize what happened until I checked the file with "........
In Debian based distros:
apt-get install jabber
Reading package lists... Done
Building dependency tree
Reading state information... Done
The following packages were automatically installed and are no longer required:
fakeroot dkms
Use 'apt-get autoremove' to remove them.
The following extra packages will be installed:
jabber-common
The following NEW packag........
I decided on using yum to help me decide even though I normaly use proftpd I decided to see what else I could find.
yum search ftp
Loaded plugins: fastestmirror
Loading mirror speeds from cached hostfile
* rpmforge: ftp-stud.fht-esslingen.de
* base: mirrors.netdna.com
* updates: updates.interworx.info
* addons: yum.singlehop.com
* extras: mirrors.netdna.com
rpmforge........
Here are the results, it is Sempron 3000+ AMD Mobile, 500Gig HDD, 512MB RAM with shared ATI Radeon graphics.
# # # # # # # ##### ###### # # #### # #
# # ## # # # #&nb........
PHP cannot access /usr/bin/opensslI have verified the username that runs the process is able to access /usr/bin/openssl and it does exist but the PHP script is saying it doesn't exist:
[code:1:1fd0f3abbe]
if (!file_exists($OPENSSL)) {
//echo "ERROR: OPENSSL $OPENSSL not foundn";
}[/code:1:1fd0f3abbe]
I don't get itI can clearly see the contents of /usr/bin by using the PHP system fu........
Clone any OS partition perfectlyIn one box I needed to copy the boot partition to another disk while retaining the MBR and other data.
I simply ran this command:
[code:1:1b1ff110ca]dd if=/dev/hda1 of=/dev/hdb1[/code:1:1b1ff110ca]
[b:1b1ff110ca]if[/b:1b1ff110ca] = source patition
[b:1b1ff110ca]of[/b:1b1ff110ca] = destination partition
Here's an interesting article on it
http://www.rajeevnet.com/hacks_hints/os_cl........
GRUB Boot FreeBSD[code:1:a7050277b7]title FreeBSD 6.0
root (hd0,2,a)
kernel /boot/loader[/code:1:a7050277b7]
Just insert the above code into GRUB's [b:a7050277b7]menu.lst[/b:a7050277b7] and make sure you set the root path correctly.
[quote:a7050277b7]Let's quickly explain what the root (hd0,2,a) means:
*hd0 stands for the primary master drive
*2 stands for partition 3
*a stands for the........
Problems surfing web/servingI noticed sometimes websites wouldn't load at random through a FreeBSD box and other systems on the same link didn't have the issue. I believe it is because of the low default limit of 128 TCP connections that caused the problem. It would also slow down any traffic that requires many connections such as Bittorrent.
The fix is to increase the amount of connections to at least 1024
Edit [b:520b050d3e]/etc/sysctl.conf[/b:520b05........
Live E-mail VerficationTwo very cool tutorials that actually connect to the supposed mail server of whatever address the user specifies to see if the e-mail address actually exists.
http://www.devshed.com/c/a/PHP/Email-Address-Verification-with-PHP/
http://www.zend.com/zend/spotlight/ev12apr.php?article=ev12apr&kind=sl&id=1782&open=1&anc=0&view=1#notes........
Centos 4.3 x64 & VMWare Server Beta[code:1:6d0b2c8c2f]
The correct version of one or more libraries needed to run VMware Server may be
missing. This is the output of ldd /usr/bin/vmware:
linux-gate.so.1 => (0xffffe000)
libm.so.6 => /lib/tls/libm.so.6 (0xf7fbd000)
libdl.so.2 => /lib/libdl.so.2 (0xf7fb9000)
libpthread.so.0 => /lib/tls/libpthread.so.0 (0xf7fa7000)
libX11.so.6 => not f........
The New Chips on the BlockThe New Chips on the Block
By Bruce Gain
Story location: http://www.wired.com/news/infostructure/0,1377,67795,00.html
02:00 AM Jun. 13, 2005 PT
We have embarked upon a new era in x86 PC computing -- so say chip giants AMD and Intel following their launches of dual-core PC processors. So how will dual-core processing change your PC computing experience? Our FAQ should help you decide whether or when you sho........
Bash Script Infohttp://www.faqs.org/docs/Linux-HOWTO/Bash-Prog-Intro-HOWTO.html#ss10.5
http://www.scit.wlv.ac.uk/~jphb/spos/notes/shell/shell5.html
http://quong.best.vwh.net/shellin20/#LtohTOCentry-41
http://www.cactus.org/~dak/shellscript.html
http://db.ilug-bom.org.in/Documentation/abs-guide/
http://pegasus.rutgers.edu/~elflord/unix/bash-tute.html
http://heather.cs.ucdavis.edu/~matloff/UnixAndC/Unix/CShellII.html
Since bash i........
CVSUp the Easy WayIf you're reading this you probably have never used CVSUp or don't know how.
CVSUp can be used for two things or just one if you prefer.
*Keeping your kernel up to date
*Keeping your port list up to date
Start by editing the following file in:
[b:76928b387d]vi /usr/share/examples/cvsup/cvs-upfile[/b:76928b387d]
It can be quite overwhelming with all the crazy options.
Basically there are only 3........
African money SCAMI have received countless of these sorts of emails where the person claims to be from an African nation which has a deposed finance minister or some other strange situation which puts millions of dollars at their disposal.
The only problem is that they need a partner to get the money out. And they have entrusted only you, yes that's right, to donate your bank account information along with SIN number so they can secretly wire the money over and you w........
ECS K7S5A Motherboard System Take Up To 2 Minutes To BootHi guys,
My motherboard is very strange. Sometimes it will take up to a few minutes to post. I have no idea it suddenly started doing this. I have tried everything and all I can figure is that it is somehow related to the USB ports possibly.
Why do I say this?
Because if I disconnect my scanner the problem occurs less frequently. I only have a printer hooked up to USB now and by........
How do you copy a DVDHow do you copy a DVDI'm assuming you mean how you can backup your DVD titles?
If you are talking movies, you should use AnyDVD and CloneDVD, they are excellent tools for backups.
For data CD's, Nero has a DVD-Copy option and that should work well for most purposes.
Hope that helps. :D........
Use Mozilla Firefox, not Internet Explorer - You'll be glad!Hey guys,
I just thought I'd recommend that everyone switch to Mozilla Firefox as their web browser. You can find it at http://mozilla.org
It is free and it is much better than IE. It has a built-in popup blocker which works great and most importantly, it doesn't have a million critical security flaws which could compromise your security such as passwords for on-line banking etc..........
This is a very weird, annoying and bizarre quirk with many distributions, especially Debian. The home and end keys don't work, but it's a simple fix as long as you found this article :)
You just have to edit /etc/inputrc:
Find the commented lines as shown below:
# "e[1~": beginning-of-line
# "e[4~": end-of-line
*If you can't find the above, just copy and paste the code below into your inputrc, it will en........
Shortcut/Easiest Way To Create A Self-Signed Key:
openssl req -new -x509 -nodes -days 1530 -out server.crt -keyout server.key
Using the above, you instantly create a self-signed certificate valid for 1530 days and you can simply skip to step #5.) below.
If You Need a Real SSLCertificate (eg. Equifax/Openssl) then you need to create a CSR request (you'll need to follow Steps 1.) and 2.) in order to create the CSR. You then upload the CSR Certi........
I didn't find any useful information that actually fixed this. My VPS was in the "Running State" and I could not stop or restart it. I kept getting "Container already locked" no matter what Idid (I tried all the suggestions in the Google results for this error).
Most of the suggestions were for Windows but I only use Linux. The other solutioins also said to restart the VZ service or even the entire hostnode and this was not acceptable to me........
A VPS Server I had just wasn't working right, code that I migrated there just wasn't working. For example, it kept telling me the connection to the database was unsuccessful, halfway through iterating through results it already had.
Then I realized it wasn't my code. Ichecked my /proc/user_beancounters and found this:
cat /proc/user_beancounters
Version: 2.5
uid resource held maxheld barrier limit failcnt........
It's actually very simple and "grep" makes it as easy as possible. I'll outline a few common scenarios and provide some examples.
Say you want to search ALLfiles within the current directory (and inside/deeper) for the text "phpinfo()"
grep -R "phpinfo()" *
If you want to search only certain files such as only .txt you would do this instead:
grep -R "phpinfo()" *.txt
As you ca........
I was getting very frustrated one day wondering why it appeared my .htaccess file was being ignored and not processed by Apache. No matter what I did it was obvious that Apache didn't care about my .htaccess file. Then I realized that the default settings must be in effect, which is that my vhost didn't explicitly allow me to override the default settings.
This usually comes down to your vhost settings. Make sure you have an entry like this in your Apache vhost settings in........
To enable Fuse to work inside a OpenVZ container it's very simple (although some people say it can't be done).
Remember that on your HN(HostNode) for OpenVZ, Fuse must be installed and the module must be loaded for this to work. In addition remember that you need the Fuse package installed inside the container of course.
vzctl set 2000 --devices c:10:229:rw --save
vzctl exec 2000 mknod /dev/fuse c 10 229
The part that most people forget........
As much of a computer nerd as Iam, I'm usually a late adopter to technology for a few reasons. Ifeel most new hyped technologies and electronics are mainly fads, and I'm also cheap.
Adopting later means you avoid the bugs, kinks and most importantly pay the lowest price, that's me being cheap again :)
I never read much about the iPhone but Isaw all the hype around it and until recently I wasn't a big fan of anything Apple until a few years ago I realize........
This is the Intel Atom 330 motherboard with integrated Realtek Gigabit NIC (Intel Desktop Board D945GCLF2 Motherboard W/ Atom 330 1.6 GHz Dual Core Processor - Mini-ITX)
I cannot achieve more than 15 MB/s, even doing a local transfer through eth0 to it's own IP.
100% 95MB 15.9MB/s 00:06
So this is not a cabling, switch or hardware issue, it seems like a driver or chipset limitation problem.
Here is my........
Icouldn't understand why on one system it took a few minutes to get the SSHlogin prompt when connecting to other systems. The other systems all had the UseDNS parameter set to no, which almost always resolves the login prompt delay.
The reason is Ubuntu and perhaps Debian and other distributions /etc/nsswitch.conf file
Edit yours to have the "hosts" line like so (notice that files and dns are the primary resolution choice........
There's a lot of outdated information and confusion for system administrator's out there.
One annoying task for many an Administrator has been backing up data in Linux. You don't need any GUI tools such as K3B or GnomeBaker. Both are excellent tools but for veteran command line users working remotely, using the keyboard is a great and possibly automated way to save yourself pain and hassle.
At a later date we'll cover how scripting can automatically backup certain........