As a fun test in an old/unloved dual CPU Xeon system, I removed the fan for the heatsink and after 1.5 hours, the system was completely stable and had surprisingly not crashed, despite exceeding or hitting the critical thermal levels........

Assign way more replicas than you have of memory on all nodes and watch the Swarm crash which can easily reproduce in a small VMfor testing. root@Deb11Docker01:~# docker ps CONTAINER ID IMAGE COMMAND CREATED STATUS PORTS NAM........

The error below can be caused by a gateway that is unpingable: docker swarm join --token SWMTKN-1-1kogg8da68gtb1j7ezaddowyy9s0an5s9tue758o20k18liskw-5h3f61hrrmv3u6agshvbtcklf 172.16.1.80:2377 Error response from daemon: manager stopped: can't initialize raft node: rpc error: code = Unknown desc = could not connect to prospective new cluster member using its advertised address: rpc error: code = DeadlineExceeded desc = context deadline exceeded........

Just in case, it is reocmmended to backup the original contents of the directory (especially your home dir) before proceeding. Setup ecryptfs Run this command: ecryptfs-setup-private It will ask you for your login password, this is so that when you login, everything is automatically decrypted by using a passphrase that is wrapped with your login. You can hit enter and leave things blank for an autogenerated passphrase (for mounting) or you can en........

We could always disable swap but this would normally be a bad idea unless you have an incredible amount of RAM and a workload that will never exceed it. However, for live/containerized and high performance environments it could be desirable. Another middle ground may be to set swappiness to a lower number. You may also want to clear your kernel's cache, which could be eating up RAM unnecessarily by c........

If you get this error when trying to SSHto a device or machine and you never even got a password prompt: Too many authentication failures This means that either the remote side is configured for key auth only, OR your client side may be attempting to auth using mulitple keys, and that exceeds the amount of attempted authorizations on the remote ssh server. If the issue is trying to auth too many times which ssh defaults to sending the keys to, you ca........

Enable "cli" mode equivalent in JunOS cli Configure Mode configure So rather than going to the console on a Cisco switch and typing "enable" and then "conf t", the equivalent in JunOS is "cli" and "configure". How Do You Apply Changes You've Made? You can make all kinds of changes to the switch, but remember they are not........

apt install software-properties-common add-apt-repository ppa:deadsnakes/ppa apt update apt install python3-pip apt install python3.7 curl gnupg python3.7-dev git ln -s /usr/bin/python3.7 /usr/bin/python3 pip3 install numpy keras_preprocessing curl https://bazel.build/bazel-release.pub.gpg | sudo apt-key add - echo "deb [arch=amd64] http://storage.googleapis.com/bazel-apt stable jdk1.8" | sudo tee /etc/apt/sources.list.d/bazel........

yum -y install wget unzip wget https://download.nextcloud.com/server/releases/nextcloud-18.0.2.zip unzip nextcloud-18.0.2.zip yum -y install php php-mysqlnd php-json php-zip php-dom php-xml php-libxml php-mbstring php-gd mysql mysql-server Last metadata expiration check: 0:58:02 ago on Fri 13 Mar 2020 02:12:49 PM EDT. Dependencies resolved. ===================================================================........

If you are getting this error it is usually caused by having more than 5 keys in your ".ssh" directory. It is a bit of a bug and this is how it manifests itself. You will find at this point that you are not given any chance to enter a password, or if you are using key based auth that the same thing happens. You'll also find that this is happening with ALLservers you try connecting to. The solution is to move away key pairs from .ssh so that there ar........

Create your netplan file vi /etc/netplan/01-netcfg.yaml network: version: 2 renderer: networkd ethernets: ens3: dhcp4: no ........

Install Errors on Version 12: This error happened on QEMU emulator version 2.11.1 pve-qemu-kvm_2.11.1-5 on Proxmox/Debian but installing on QEMU.12 on Centos 6 did not produce the error. *Update it is not related to the OS or QEMU version. This happened in Centos 6 too after a second install. What really causes this even though you successfully install........

The strange thing is that usually the first install or two will work on any new machine but then it suddenly won't. I had this experience on QEMU 2.13 on a different machine. There is something finicky or buggy about the CUCM installer even when choosing the same virtual hardware specs. qemu-kvm command: /usr/libexec/qemu-kvm -version QEMU PC emulator version 0.12.1 (qemu-kvm-0.12.1.2-2.506.el6_10.1), Copyright (c) 2003-2008 Fabrice Bellard ........

If you don't aleady have it, you'll need EPEL Install LXC yum -y install lxc lxc-templates Loaded plugins: fastestmirror Setting up Install Process Loading mirror speeds from cached hostfile * base: mirror.it.ubc.ca * epel: mirrors.kernel.org * extras: mirror.it.ubc.ca * updates:........

initiator = client target = server These are the first concepts you should understand which is that in iscsi essentially the "initiator" is the client and the "target" is the server. iSCSI is derived from the old fashioned SCSI that us oldtimers grew to love. The "i" stands for Internet and the SCSI stands for "Small Computers Systems Interface" (SCSI). iSCSI Target (Server)Setup targetcli is the pac........

[root@thetor2017 conf]# service httpd restart Stopping httpd: [ OK ] Starting httpd: WARNING: MaxClients of 3000 exceeds ServerLimit value of 300 servers, lowering MaxClients to 300. To increase........

Server Side Config 1.) First install nfs-utils yum -y install nfs-utils 2.) Configure nfs share Create a directory for your NFS share mkdir /datastore Create your NFS share in /etc/exports echo "/datastore 10.220.101.0/24(rw,sync,no_root_squash)" >> /etc/exports systemctl restart nfs........

#mount the VCSA DVD mount /dev/sr0 /mnt/cd #alternatively you could mount the iso directly mount -o loop vcsa.iso /your/mount/path #for this purpose we are using the CLI installer on Linux cd /mnt/cd/vcsa-cli-installer/lin64 #no it's not going to be that easy you can't just run vcsa-deploy like that you need to use a template or configured .json file ./vcsa-deploy Usage: vcsa-deploy [-h] [--version] [--supported-deploymen........

This happens because Dovecot limits the maximum IMAPconnections per IPto just 10. This may be fine for a single client side IPbut if an entire office or multiple users are behind one IPor a single heavy user is active then you will get bizarre errors in your e-mail clients such as "Password Incorrect" or similar in Thunderbird. It won't be obvious on the client side as to what the problem is and they will probably just think the server is misconfi........

This is a VIA made VL805 USB 3.0 Chipset with 4-ports and MOLEX powered. First of all this unit was cheap at about only 9 USD with fast shipping. My biggest concern was if this was a quality unit and would it really give you full USB 3.0 speeds (some people reported with similar cards that for some weird r........

I get the following error "Installer Crashed" on 18.1 MATE 64-bit when installing by NFS/PXE. Yet it was able to at least detect and use my NIC (perhaps the driver was only activated because of PXE/NFS being used)? When using 18.1 Cinnamon on CD the NIC does not work but the installer did succeed. However it doesn't work right, I can't login graphically and get some Cinnamon OOMerror but how can this be with 8GB of RAM straight from login?........

vzkernel-2.6.32-042stab116.2.x86_64.rpm&n........

When you start uploading larger images in Wordpress you have to make sure your maximum attachment size is large enough and that the execution time is not too short: Uploading Error HTTP error. [Thu May 12 16:32:25 2016] [error] [client 10.10.5.2] PHP Fatal error: Maximum execution time of 30 seconds exceeded in /httpdocs/blog/wp-includes/class-wp-image-editor-gd.php on line 182 Solution Edit p........

This can happen because port 80 is not open, or your license has expired and/or your IP is out of date and also if the license server itself from cPanel is having issues. In most cases as long as you have a valid license the following command will solve it: /usr/local/cpanel/cpkeyclt Updating cPanel license...Done. Update succeeded. Building global cache for cpanel...Done Cannot........

grub> root (hd0,0) root (hd0,0) Filesystem type is ext2fs, partition type 0xfd grub> setup (hd0) setup (hd0) But if you do: root (hd1,0) setup (hd1) it does work, I think hd0/sda had a GPT partition that was not removed properly (what I did was just dd bs=512 count=1 the partition table from another drive since the partition table should be identical). Checking if "/boot/grub/........

Here is the scenario you or a client have a remote machine that was installed as a standard/default minimal Centos 6.x machine on a single disk with LVM for whatever reason. Often many people do not know how to install it to a RAID array so it is common to have this problem and why reinstall if you don't need to? In some cases on a remote system you can't easily reinstall without physical or KVM access. So in this case you add a second physical or disk or already ha........

Iwas surprised to see that Linux Mint at the latest 17.2 version still has NO mdadm installer option, and worse the installer will not be able to create a proper booting environment even when you do install it. How to setup mdadm in Linux mint LiveCD sudo su apt-get install mdadm # partition as you need and then create your mdadm devices # create your SWAP md0 mdadm --create /dev/md0 --level=1 --raid-devices=2 /dev/sda1 /d........

freshclam ERROR: Can't open /var/log/clamav/freshclam.log in append mode (check permissions!). ERROR: Problem with internal logger (UpdateLogFile = /var/log/clamav/freshclam.log). Tue Oct 13 13:49:35 2015 -> WARNING: Incremental update failed, trying to download daily.cvd Tue Oct 13 13:49:35 2015 -> WARNING: Can't download daily.cvd from db.local.clamav.net Tue Oct 13 13:49:35 2015 -> Trying again in 5 secs...........

An error occurred during a connection to site.com. SSL received a record that exceeded the maximum permissible length. (Error code: ssl_error_rx_record_too_long) The page you are trying to view cannot be shown because the authenticity of the received data could not be verified. Please contact the website owners to inform them of this problem. When the above happens in our experience it is a misconfiguration of........

Have you ever tried to run a command like rm to delete several hundred thousand files? Iam not sure what the limit is but any time it is exceeded you need to use a work around like below (which will delete any number of files). Solution find . -maxdepth 1 -name "*.*" -print0 | xargs -0 rm........

#count=10000 makes an image of 10000MB make sure your image is at least the same as your existing dd if=/dev/zero of=yourimage.img bs=1M count=10000 # losetup -fv newimage.raw # fdisk -cu /dev/loop0 # kpartx -a /dev/loop0 # dd if= of=/dev/mapper/loop0p1 # e2fsck -f /dev/mapper/loop0p1 # resize2fs /dev/mapper/loop0p1 # a lot of guides tell you to edit /etc/fst........

I flashed an LSI Logic firmware to it and it broke the BIOS (cannot do Ctrl+R) for booting purposes but allows other functionality to work normally. I tried downgrading to a Dell firmware for Perc 6i but it won't work, not even with MegaCli wget http://downloads.dell.com/FOLDER00416606M/1/SAS-RAID_Firmware_W83M2_LN32_6.3.1-0003_A14.BIN --2013-08-26 12:53:39-- http://downloads.dell.com/FOLDER00416606M/1/SAS-RAID_Firmware_W83M2_LN32_6.3.1-0003_A14.BIN Resolvi........

LSi Megaraid At first it was configured as a RAID 0, then I deleted the Virtual Disk Group. I thought both drives would be shown and detected in Linux as sda and sdb but it actually shows nothing. To make them work you have to hit Ctrl+R before the system boots (when prompted) and create a Virtual Disk Group. In my case I created each one as RAID 0 (with a single drive only) as I just wanted JBOD but there is no such option or default in these Dell Pe........

mkdir: cannot create directory 'test': Disk quota exceeded You are out of inodes usually: df -i Filesystem Inodes IUsed IFree IUse% Mounted on /dev/simfs 200000 200000 0 100% / none ........

The error itself "mkdir(): Too Many Links" is not very useful, but I'll translate it into plain English. It means you've reached the filesystem's limit of how many directories can be created in a single directory. In this case for ext3 the limit is 32000 and it was exceeded. What's the solution? The simple solution is to move those directories into more subdirectories possibly sorting them by date, alphabet or numerically.........

Client Log OpenSSH_4.3p2, OpenSSL 0.9.8e-fips-rhel5 01 Jul 2008 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug1: Connecting to 192.168.1.253 [192.168.1.253] port 22. debug1: Connection established. debug1: permanently_set_uid: 0/0 debug1: identity file /root/.ssh/identity type -1 debug1: identity file /root/.ssh/id_rsa type 1 debug1: identity file /root/.ssh/id_d........

vzquota : (warning) block_hard_limit [102] < block_current_usage [520824] This is because your disk usage of the container exceeds the quota. Eg. once on a test container I had accidentally set it to 32MB yet the OS took about 600MB. Just set the quota to something bigger than the currently used space to solve it. vzctl set 3891 --diskspace 5G:5G --save........

cat | grub --device-map=/dev/null Now pay close to the attention of the beginning. Type: "device (hd0) VPS.img" this is telling what hd0 will be to GRUB and we're telling it the disk image file "VPS.img" in the current directory is hd0, you can specify alternate paths and image names of course. GNU GRUB version 0.97 (640K lower / 3072K upper memory) [ Minimal BASH-li........

The size of the message you are trying to send exceeds a temporary size limit of the server. The message was not sent; try to reduce the message size or wait some time and try again. The server responded: 4.5.3 Error: too many recipients. We set this in main.cf: smtpd_client_recipient_rate_limit=0 We didn't specify it before and the default is said to be 0/unlimited and it still didn't change anything.........

I really am a Linux fan but my comments here may not show it. Although I'm quite familiar with Linux CLI to administer servers, I find Linux GUI OS's like Ubuntu at times very clunky. This is partially because there's no such thing as a "self-made" Linux from scratch where the UIwas designed by a single team. Linux is made up of several different projects that are generally completely separate and this lack of integratiion is a key issue that makes things f........

I am watching the Canucks riot and a reporter said Twitter is down. My home connection on Shaw is fine, but when Iused my Rogers network over the cell, it says "Rate Limit Exceeded". I wonder if this is a transparent redirect by Rogers under police order? I noticed that the Telus network loaded Twitter just fine.........

It's weird because I have a nearly identical box and setup and I can update the ovzkernel-PAE* just fine but on this box it doesn't work. I only get this error with the openvz.repo and not others such as Centos-Base.repo With my other server it works normally: ================ Setting up Update Process Resolving Dependencies --> Running transaction check ---> Package ovzkernel-PAE.i686 0:2.6.18-238.12.1.el5.0........

GNU GRUB version 0.97 (640K lower / 3072K upper memory) [ Minimal BASH-like line editing is supported. For the first word, TAB lists possible command completions. Anywhere else TAB lists the possible completions of a device/filename.] grub> root (hd1,0) Filesystem type is ext2fs, partition type 0xfd grub> setup........

yum -y install vnstat chown nobody.nobody -R /var/lib/vnstat/ #replace venet0 below with your desired interface sudo -u nobody vnstat -u -i venet0 #edit: vi /etc/sysconfig/vnstat #VNSTAT_OPTIONS="-i venet0" # only use the sed below if you are using venet0 instead of eth0 or replace accordingly sed -i 's/eth0/venet0/g' /etc/sysconfig/vnstat [root@monitor]# yum install vn........

find what MPM Apache is using, it will either be using "worker" or "prefork" apachectl -l Compiled in modules: core.c prefork.c http_core.c mod_so.c In my case it is "prefork" vi /etc/httpd/conf/httpd.conf Find the section that looks like this (by default one will normally exist for prefork and for worker, but in my case I only care a........

Centos 5 Postfix and SPAMASSASSIN Tutorial yum install spamassassin chkconfig spamassassin on vi /etc/mail/spamassassin/local.cf ############## #required_hits 5 #report_safe 0 #rewrite_header Subject [SPAM] #5 is the least restrictive (means only the most obvious SPAM is caught. 0 is obviously the most restrictive/sensitive and would have lots of false positives require........

Openvz problem, it is confusing because it's an inode issue and there is enough free space. cp: cannot create regular file `forums/memberlist.php': Disk quota exceeded /dev/simfs 60G 20G 41G 33% / none 2.0G 4.0K 2.0G 1% /dev........

yum exits in the middle The problem is this VPS seems to be an OpenVZ template from HyperVM. The only way to make it work was to disable i386 packages since this was an x64 kernel. That shouldn't be necessary but it was the only way to make yum stop quitting after the first package or two. I couldn't find any issue by checking the logs either. echo y|yum install vim-minimal telnet expect jwhois net-tools slocate iptables elinks gawk L........

had trouble trying to revert Ubuntu 10.04 LTS from grub2, won't boot mdraid and did not even install mdadm during the installation! I have tried moving back to GRUB 0.97 backed up original /boot and then copied /boot from an old Debian install. Modified device.map and menu.lst and put the appropriate kernels and initrd for Ubuntu back in /boot I ran grub: root (hd0,1) grub> setup (hd0) Checking if "/boot/grub/stage1........

mdadm --assemble --scan mdadm: /dev/md/diaghost05102010:2 has been started with 2 drives. mdadm: /dev/md/diaghost05102010:1 has been started with 2 drives. mdadm: /dev/md/diaghost05102010:0 has been started with 2 drives. -bash-3.1# cat /proc/mdstat Personalities : [linear] [raid0] [raid1] [raid6] [raid5] [raid4] [multipath] md125 : active raid1 sda1[0] sdb1[1] 14658185 blocks super 1.2........

I decided on using yum to help me decide even though I normaly use proftpd I decided to see what else I could find. yum search ftp Loaded plugins: fastestmirror Loading mirror speeds from cached hostfile * rpmforge: ftp-stud.fht-esslingen.de * base: mirrors.netdna.com * updates: updates.interworx.info * addons: yum.singlehop.com * extras: mirrors.netdna.com rpmforge........

Quick Tutorial On Starting A Web Site[b:3cef3c01b6]Step 1.[/b:3cef3c01b6] Purchase a Domain Name (eg. yoursite.com) [b:3cef3c01b6]Step 2.[/b:3cef3c01b6] Design your site using a program such as Microsoft Frontpage or Macromedia Dreamweaver. If you are unable or unfamiliar with doing this you may want to hire a company to create your site (many of them will handle each aspect of setting up your site). [b:3cef3c01b6]Step 3.[/b:3cef3c01b6] Host your site........

Have you ever seen this dreaded message in your Apache/HTTPD /var/log/httpd/error_log? [error] server reached MaxClients setting, consider raising the MaxClients setting The error itself is slightly misleading. Ibelieve this happened to one of my servers, I found Apache was running still, and that you could telnet to port 80 but no respnose would be given. For some reason my error log initially did not have the above error, but after a restart I saw........

A VPS Server I had just wasn't working right, code that I migrated there just wasn't working. For example, it kept telling me the connection to the database was unsuccessful, halfway through iterating through results it already had. Then I realized it wasn't my code. Ichecked my /proc/user_beancounters and found this: cat /proc/user_beancounters Version: 2.5 uid resource held maxheld barrier limit failcnt........