If you are converting a generic wifi IP camera to ethernet, it may not be that simple as many are default hard coded to a static IP of 192.168.1.168 and login info admin/admin. From there you can login to the camera and assign it to DHCP by going to http://192.168.1.168 For security these cameras +DVR should be on a separate untagged VLAN or if possible a physically isolated non-internet connected switch/network. The reference below is applicable to many of the r........

Bonding is an excellent way to get both increased redundancy and throughput. It is similar to the "Network Teaming" feature in Windows. There are a few different modes but we will use mode 6, I think it's the best of both worlds, as it is not just a failover, but it provides round robin, so you will get redundancy and load balancing. So if you have a 1G single port, you will have a combined throughput of 4G at this point. Just bear in mind that the true thr........

Enable "cli" mode equivalent in JunOS cli Configure Mode configure So rather than going to the console on a Cisco switch and typing "enable" and then "conf t", the equivalent in JunOS is "cli" and "configure". How Do You Apply Changes You've Made? You can make all kinds of changes to the switch, but remember they are not........

In most of the Cisco router IOS I find the ports like ge0/0 ge0/1 and ge0/2 or whatever your ports are down. They will not even give you a link light. So one of the first tasks should be getting the port you are working with up. In my case the first goal is often connectivity with the LAN and WAN. LAN = your local area network (eg. in the office/home ) WAN= your ISP/public internet (eg. fiber/cable/dsl/ethernet).........

Switch#show ip dhcp snooping Switch DHCP snooping is disabled DHCP snooping is configured on following VLANs: 1 Insertion of option 82 is enabled circuit-id format: vlan-mod-port remote-id format: MAC Option 82 on untrusted port is not allowed Verification of hwaddr field is enabled Interface&nb........

Enter configuration console: enable configure terminal This is important because if your console doesn't look like below none of the commands will work! Switch(config)# Save and Apply Settings wr Show Switch Configuration: show run Show Port List/Sta........

This works on the 2000 and 3000 series generally. *The easy way is to just hold the mode button for 10+ seconds. The full/proper way is below: 1.) Either power on the unit and hold the "mode" button or hold the "mode" button until you see the below: 00:04:08: %SYS-7-NV_BLOCK_INIT: Initalized the geometry of nvram 00:04:08: %EXPRESS_SETUP-6-CONFIG_IS_RESET: The configur........

You can find many ways to specify the VLANin your network configuration but Ifind this is the simplest and quickest. In this case we are talking about a bridged adapter "vmbr0" but it works even if you just had a normal non-bridged interface. The key here is that in vmbr0 you'll notice there is no IP address. We just specify "manual". Below it is a similar stanza for "vmbr0.58" in this case 58 represents the VLAN (change........

Centos when copying old files and restarting it seems load everything fine and then says [FAILED] with no log or other message. service restart named named [FAILED] Check more thoroughly you may have missed the error if you have lots of zones! service named restart|grep error zone 1.168.192.in-addr.arpa/IN: not loaded due to errors. zone 2.168.192.in-addr.arpa/IN: no........

forcedeth 0000:00:08.0: irq 25 for MSI/MSI-X forcedeth 0000:00:08.0: eth0: MSI enabled forcedeth 0000:00:08.0: eth0: no link during initialization ADDRCONF(NETDEV_UP): eth0: link is not ready forcedeth 0000:00:08.0: eth0: link up ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready Dec 1 18:21:32 box15 kernel: forcedeth: Reverse Engineered nForce ethernet driver. Version 0.64. Dec 1 18:21:32 box15 kernel........