This is certainly a poor design, as you can read many seasoned admins who have updated their iDRAC only to have it killed. One possible cause is not by doing all the incremental updates, doing updates from an old iDRAC to one many revisions newer is a sure way to kill things, but even then there is no guarantee based on the amount of failures. List of threads of people's dead iDRAC's:........

This should work for most console ports of other manufacturers too. It is a quick and simple method for emegencies or deploying a few appliances/devices in a non-standard environment or small environment. However, if this is a route thing, or the equipment is not physically close to you, it would be best to use some sort of "Terminal" server which is an IP connected switch with several serial ports built-in for this purpose. Normally they accessible by web/........

Welcome to our in-depth guide on configuring NVIDIA GPUs with Docker on Ubuntu. This post is tailored for developers, data scientists, and IT professionals who are looking to leverage the power of NVIDIA's GPU acceleration within Docker containers. Whether you're working on machine lea........

Are you new to the company, datacenter or a third party who is responsible for deploying a fleet of servers from scratch. The first step is to normally login to the KVM so you can perhaps manually reinstall, PXE boot the Cloud Image or reimage/reinstall an OS but you need access to the KVM/IP or what Dell calls iDRAC. It's common that you may have forgotten this information or that another employee or colleague has changed the info and did not tell you, that they have left the........

In our 2024 VPS Server/Cloud Buyer's Guide, we place the location of your VPS/hosting/server as one of the priorities that is often overlooked. 2024 Update - Datacent........

This was done on a 2900 but applies to all the switches of the same era. Step 1 - Power Cycle and enter recovery mode If you have physical access you can power cycle and hold the mode button down for 15 seconds. After that the SYS light will flash on the switch and you will see the following screenshot. If you don't have physical access (eg. it is a datacenter swich over console only) then power cycle and hit "Ctrl+Pause/B........

The reason for this article is because a lot of us don't physically see our hard drives they are often remote in a datacenter etc and the actual serial number we see in SMART is not enough to check for some manufacturers. A good example is our first one the Toshiba === START OF INFORMATION SECTION === Device Model: TOSHIBA DT01ACA200 Serial Number: 33FMDW4AS........

When installing Windows 2012 I cannot get around that error for some reason it just keeps on happening. code:0xc0000005........

Does anyone have any suggestions on how to handle this error code? It is for a client who has a Windows 2008 R2 Datacenter License and wants to install virtual instances on the same host.........

#solution Edit /etc/yum.repos.d/openvz.repo For the first two entries comment out #mirrorlist and uncomment #baseurl and then it worked openvz yum problem Centos 6.5 cannot find file on mirror: yum update Loaded plugins: fastestmirror Determining fastest mirrors * openvz-kernel-rhel6: mirrors.ustc.edu.cn * openvz-utils: mirrors.ustc.edu.cn base ........

To activate your Windows server trial which gives you 180 days: Start ->Right Click (My Computer). Click "Activate Windows now" To renew your license for 180 days (can be done 6 times): Start -> Type this command: slmgr.vbs -rearm Wait a few minutes until it says it is successful (unless you get that message it has not worked or been done)........

Once I set a new MAC address everything was fine and finally anything can be pinged etc.., I've had this happen with many clients in different datacenters on different hardware.........

Let's keep this simple, it's horrible, not only is the picture quality horrible (it's not a big deal) but the keyboard input is an issue. You have to type slowly, lightly and carefully otherwise 1-keystroke could end up being dozens of keystrokes. It's also a confusing unit for many datacenter techs, I've seen these units hooked up wrong and the instructions themselves aren't clear. I had to resort to shipping one to my office and take my phone pictures of the setup for th........

I've run into two issues with Lantronix based KVMs on various servers and here's how I solved them (with that said I like these units as they are Java based and OS independent and work very well, unike some other models like Startech). 1.) If you are connected by USB only and you're sure USB support from the BIOS is enabled, you just need to click the following in Lantronix Interfaces -> Keyboard/Mouse Check "Force USB Full Speed Mode", this fixed the issu........

This is something I often setup for clients because it's very helpful for people in datacenters, this allows custom OS installs on demand, you can customize it more by using kickstart etc.. but here's a base I use before customizing more: This little script below will install everything you need to get booting by PXE Linux. It also assumes you set a local IP (be sure not to overwrite your existing IP) on eth0:0 (note the :0) as 192.168.1.10 and it........

ifup eth0 SIOCSIFFLAGS: Cannot allocate memory Failed to bring up eth0 This is on a Centos 5.5 machine with OpenVZ kernel 2.6.18-238.12.1.el5.028stab091.1PAE, I updated 3 systems with the same hardware to the same kernel and for some reason the network didn't come back. This only happened once the first time I booted into the new kernel and hasn't happened again but this is a serious issue for those running systems from remote locations such as a datacente........

It's weird because I have a nearly identical box and setup and I can update the ovzkernel-PAE* just fine but on this box it doesn't work. I only get this error with the openvz.repo and not others such as Centos-Base.repo With my other server it works normally: ================ Setting up Update Process Resolving Dependencies --> Running transaction check ---> Package ovzkernel-PAE.i686 0:2.6.18-238.12.1.el5.0........

Apr 30 17:07:07 localhost kernel: [12265558.582378] r8169: eth0: link up Apr 30 17:07:07 localhost NetworkManager: (eth0): carrier now ON (device state 1) Apr 30 17:07:08 localhost kernel: [12265559.237961] r8169: eth0: link down Apr 30 17:07:08 localhost NetworkManager: (eth0): carrier now OFF (device state 1) Apr 30 17:07:11 localhost NetworkManager: (eth0): carrier now ON (device state 1) Apr........