• Linux and Windows Dual Boot Issue NIC Won't work After Booting Windows


    In Windows, with some NICs, especially Intel, Windows may enable features on the card that break it in Linux. It is hard to troubleshoot as what you'll see is that the NIC is still detected in Linux, the NIC/port will be up but nothing will work (eg. DHCP requests or even static IPs won't work). You may see STP bridge traffic but that is all. In a corporate environment this can result in many calls to support and is essentially downtime and an unnecessary waste of resource........
  • How to use the FTDI USB serial cable to RJ45 adapter to connect to the console on Cisco/Juniper Switch Router Firewall in Linux Ubuntu Debian Redhat


    This should work for most console ports of other manufacturers too. It is a quick and simple method for emegencies or deploying a few appliances/devices in a non-standard environment or small environment. However, if this is a route thing, or the equipment is not physically close to you, it would be best to use some sort of "Terminal" server which is an IP connected switch with several serial ports built-in for this purpose. Normally they accessible by web/........
  • (firefox:9562): LIBDBUSMENU-GLIB-WARNING **: Unable to get session bus: Failed to execute child process "dbus-launch" (No such file or directory) Solution


    (firefox:9562): LIBDBUSMENU-GLIB-WARNING **: Unable to get session bus: Failed to execute child process "dbus-launch" (No such file or directory) ExceptionHandler::GenerateDump cloned child 9743 ExceptionHandler::WaitForContinueSignal waiting for continue signal... ExceptionHandler::SendContinueSignalToChild sent continue signal to child [Parent 9562, Gecko_IOThread] WARNING: pipe error (40): Connection reset by peer: file /build/firefox-EymEXX/fire........
  • Mikrotik RouterOS CHR/ISO Basic and Quick Setup Howto Guide


    Many people may not be aware that you can turn commodity hardware into a Mikrotik OS and there are various options which is "CHR" (Cloud Hosted Router) which is a VMimage meant for Virtualization only (seriously, I've tried to dd the image to a physical server and it just crashed as it does not contain any drivers for physical). One note as well if you are trying to do a baremetal install you may get an error "Error Loading Operating System" or........
  • ADATA USB Thumb Drive Issues


    This is the reason that I don't like the new ADATA USB drives such as the UV128/64GB or 128GB drives and other ones that look to be the same style (the green sliding USB connector). They just don't work well from new and never work properly at any point. [ 788.242463] usb 1-1.2: new high-speed USB device number 16 using ehci-pci [ 788.339816] usb 1-1.2: New USB device found, idVendor=125f, idProduct=db8a [ 7........
  • how to use ifplugd in Linux to execute a command or script when a NIC cable is unplugged or plugged in


    It is fairly simple to use once you know how to use it. However, the tricky thing is that by default it doesn't seem to be active or listen on any interface on manually specified. How To Install ifplugd First we install ifplugd sudo apt install ifplugd Let's enable it on our desired device(s) vi /etc/default/ifplugd set this line as so:........
  • Ubuntu Debian Linux Mint r8169 r8168 Network Driver Problem and Solution


    This problem has been around forever, Linux seems to think it is fine to use the r8169 driver for an r8168 NIC but this often causes problems including the link not working at all. In my case ethttool shows the link up and detected but it simply does not work especially on a laptop that has been resumed from suspension. Sometimes it takes several minutes for it to work or to unplug and replug the ethernet. Here is the solution: Install th........
  • Apache htaccess and mod_rewrite how to redirect and force all URLs and visitors to the SSL / HTTPS version


    It is really simple using .htaccess with mod_rewrite. Here is all you need: RewriteCond %{SERVER_PORT} 80 RewriteRule ^(.*)$ https://site.com/$1 [R=301,L] Another more graceful way is to use the %{SERVER_NAME}variable to make it dynamic. Just be careful that the server name will always match what you expect. (eg. if you are doing load balancing or clustering what if the server name may be somethi........
  • Linux use growisofs to burn a larger file on a BD-R / Bluray Disc


    growisofs -Z /dev/sr0 critical.tar.gz.gpg Executing 'genisoimage critical.tar.gz.gpg | builtin_dd of=/dev/sr0 obs=32k seek=0' I: -input-charset not specified, using utf-8 (detected in locale settings) File critical.tar.gz.gpg is larger than 4GiB-1. -allow-limited-size was not specified. There is no way do represent this file size. Aborting. :-( write failed: Input/output error #remember to us........
  • genisoimage errors with long filenames and deep directory structures


    You'll have to violate the iso9660 standards but it is necessary if you want to preserve your filesystem and filenames and shouldn't be an issue as long as you are using a modern OS like Linux. genisoimage -o Backup-Myfiles.iso -r -J -joliet-long /some/path/ You will get errors like below (even enabling joliet-long didn't help) genisoimage: Error: /some/filename.pdf have the same Joliet name Joliet tree sort failed. The -joliet-lo........
  • Linux Kernel USB Export Errors


    4.374647] usb_common: exports duplicate symbol usb_get_dr_mode (owned by kernel) [ 4.403334] usbcore: exports duplicate symbol __usb_get_extra_descriptor (owned by kernel) [ 4.427736] xhci_hcd 0000:00:15.0: xHCI Host Controller [ 4.427844] xhci_hcd 0000:00:15.0: new USB bus registered, assigned bus number 1 [ 4.429040] xhci_hcd 0000:00:15.0: hcc params 0x200077c1 hci version 0x100 quirks 0x01109810 [ 4.429141] xhci_hcd 0000:00:15.0: cache line size of 64 is not sup........
  • wodim / cdrecord error cannot burn DVD or BDR .iso Errno: 5 (Input/output error), write_g1 scsi sendcmd: no error


    dvd+rw-mediainfo /dev/sr0 INQUIRY: [ASUS ][BW-16D1HT ][3.00] GET [CURRENT] CONFIGURATION: Mounted Media: 11h, DVD-R Sequential Media ID: RITEKF1&n........
  • Linux Mint Black Screen after boot no graphics solution


    This is not the normal "black screen"issue and I was shocked to eventually find out why. The normal advice of reconfiguring Xorg didn't work. Even booting into "Recovery Mode" did not help. Here is the short end of the stick that fixed it: sudo apt-get install mdm mate-desktop-environment Yes you got it right, mdm and the mate-desktop-environment / gnome were somehow uninstalled. This must be whe........
  • Intel NUC J3455 Linux Kernel freeze slowness 4.4.98 errors


    It looks like this has something to do with APIC but I am not sure. I have similar CPUs with a different MB and BIOS that work fine on the same type of kernel. A lot of time the issue is because of the C-step setting in the BIOS. The same thing happened on the 2.6 kernel with Centos 6 but this is a homebrew 4.4 kernel soI am not sure why it is happening when even Centos 7 (3.2) kernel works OK. Solution - It comes down to the BIOS set........
  • Why won't my Linux Mint boot after I manually installed a new kernel?


    Why won't my Linux Mint boot after I manually installed a new kernel? eg. apt-get install linux-image-newerone Do this dpkg -l|grep linux-image|grep extra ii linux-image-extra-3.16.0-38-generic 3.16.0-38.52~14.04.1&nb........
  • USB Device/MP3 Player not working properly and can't browse the device filesystem? Check the cable twice and again!


    Here is a simple MP3 player and now there's a reason to understand why the supplied cable has some kind of capacitor and is very short. These devices can be VERY finicky and any voltage fluctuation or difference is enough to cause issues. Take for example the error messages from Linux Mint: [804829.895414] usb 1-1: USB disconnect, device number 11 [806961.109030] usb 1-1: new high-speed USB device number 12 using xhci_hcd........
  • Track 01: 34 of 1726 MB written (fifo 100%) [buf 99%] 3.6x.Errno: 5 (Input/output error), write_g1 scsi sendcmd: cmd timeout after 1.897 (40) s CDB: 2A 00 00 00 44 A9 00 00 1F 00 resid: 6144 cmd finished after 1.897s timeout 40s write track da


    These errors believe it or not are simply because of not being the root user or running with sudo! However if you didn't know to try as root you'd think there was a problem with your burner or disc Essentially it looks like without root you cannot send the required scsi commands to continue writing. Ithink cdrecord should have built-in tests or safeguards to see if it has the permissions to run the required commands. I guess for more advanced users the idea is simila........
  • mdadm frozen and doesn't realize array is dead/missing failed due to unplugged drives


    This was a surprising bug but I unplugged all drives for an array md127. At first it was just 1 drive and mdadm seemed to notice this. I unplugged the second drive taking the array offline but mdadm did not realize it was offline and still showed a non-existent disk as being part of it. This created problems trying to unmount it or even to stop this array with mdadm freezing. As for how to fix it I can only think of making sure you are not in a mounted path of........
  • DRBD Split-brain solution


    Uh oh [17925926.174277] block drbd0: Handshake successful: Agreed network protocol version 96 [17925926.174325] block drbd0: conn( WFConnection -> WFReportParams ) [17925926.174342] block drbd0: Starting asender thread (from drbd0_receiver [1682]) [17925926.174432] block drbd0: data-integrity-alg: [17925926.174581] block drbd0: drbd_sync_handshake: [17925926.174586] block drbd0: self 2AAE66AF9252D6DB:2815BF........
  • remove gpt partition linux


    sudo fdisk /dev/sdh WARNING: GPT (GUID Partition Table) detected on '/dev/sdh'! The util fdisk doesn't support GPT. Use GNU Parted. WARNING: The size of this disk is 8.0 TB (8001563221504 bytes). DOS partition table format can not be used on drives for volumes larger than (2199023255040 bytes) for 512-byte sectors. Use parted(1) and GUID partition table format (GPT). The device presents a l........
  • forcedeth MCP55 Nforce3600 Nvidia Network NIC Card Not working in Linux at 1gigabit speeds


    Now many people report this card simply not working in various Linux distros and kernels. My issue is different, it always works at 100mbit (eg. plugged into a 100mbit switch) but no matter what 1000M/gigabit switch I would try, it would never work. The link would be up (the lights were on) and the OS detected the link as being up as well but it wouldn't work at all and could not pass data in or out (not even a ack/ping). There is one simple solution and command........
  • ECC Errors in action


    Message from syslogd@server at Sep 14 11:35:59 ... kernel:[Hardware Error]: MC4 Error (node 1): DRAM ECC error detected on the NB. Message from syslogd@server at Sep 14 11:35:59 ... kernel:[Hardware Error]: Error Status: Corrected error, no action required. Message from syslogd@server at Sep 14 11:35:59 ... kernel:[Hardware Error]: CPU:6 (10:8:0) MC4_STATUS[Over|CE|MiscV|-|AddrV|CECC]: 0xdc00400021080813........
  • Linux check NIC ethernet port network card speed


    ethtool eth0 Settings for eth0: Supported ports: [ TP MII ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full ........
  • cPanel VPS Server Cannot Login as root


    I was worried the server was hacked, I was logged in already as root but couldn't login to CPanel or a new SSHsession. I even reset the password from the shell and it did not work still. The reason is CPanel Hulk, it detected a brute-force attack so it locked down the root account entirely even from the correct password. According to cPanel the best way around this is to whitelist your IP.........
  • Sendmail Gmail.com blocking


    relay=alt4.gmail-smtp-in.l.google.com. [74.125.136.26], dsn=4.0.0, stat=Deferred: 421-4.7.0 [ 10] Our system has detected an unusual rate of This is strange because the mail server IP is not blacklisted anywhere and the IP itself has not been used for years and this server is clean and has only sent a few e-mails to gmail.com in its entire time. I wonder if this is a legacy block on a whole range of IPs as punishment for others in the block........
  • LSI MegaRAID Adventures, Guide and HowTo


    LSi Megaraid At first it was configured as a RAID 0, then I deleted the Virtual Disk Group. I thought both drives would be shown and detected in Linux as sda and sdb but it actually shows nothing. To make them work you have to hit Ctrl+R before the system boots (when prompted) and create a Virtual Disk Group. In my case I created each one as RAID 0 (with a single drive only) as I just wanted JBOD but there is no such option or default in these Dell Pe........
  • Samsung Galaxy Note Upgrade to ICS 4.0 microSDHC card not detected/dataloss after upgrading - possible solutions


    I backed up everything in the /mnt/sd_card directory thinking that some dataloss could occur for some reason but purposely left my microSDHC unbacked up thinking that "it won't touch that since it's external" and Samsung's and other manufacturers website even say this (that it won't be affected and not to worry etc). Apparently I was wrong, my microSD was "undetected" and asked to be formatted after the upgrade (there goes 3-months worth of family photos). No........
  • Error: detected vswap CT config but kernel does not support vswap This means either old kernel or bad config (physpages NOT set to 0:unlimited) Solution for OpenVZ


    Error: detected vswap CT config but kernel does not support vswap This means either old kernel or bad config (physpages NOT set to 0:unlimited) Solution vzctl set $veid --physpages 0:unlimited --save........
  • failed to IDENTIFY (INIT_DEV_PARAMS failed, err_mask=0x80)


    [ 12.460014] ata1: SRST failed (errno=-16) [ 17.626677] ata1: link is slow to respond, please be patient (ready=0) [ 22.480011] ata1: SRST failed (errno=-16) [ 27.646681] ata1: link is slow to respond, please be patient (ready=0) [ 38.106817] ata1.01: failed to IDENTIFY (INIT_DEV_PARAMS failed, err_mask=0x80) [ 48.266676] ata1: link is slow to respond, please be patient (ready=0)........
  • mdadm/Debian problem


    This is one in a series of weird things whichIthought was motherboard related (I RMA'd the motherboard), the RAM tests fine with memtest86 and I used badblocks on both RAID 1 members with no errors and smartctl is happy with them. Basically the array crashes the kernel a lot and has issues when writing. [112322.723465] md0: rw=0, want=14958668696, limit=1887460480 [112322.731077] attempt to access beyond end of device [112322.731087] md........
  • PayPal Solution - Error Detected Error Message We were unable to decrypt the certificate id. We were unable to decrypt the certificate id.


    Error Detected........
  • Linux Burn MP3 CD On the Fly using


    I finally decided to look into some utils that did this, and the first one I found is "mp3burn". It is unbelievable simple and perfect. *2017-11 update and mp3burn is still available in standard repos such as Ubuntu 14/16 so this is a current and working project. Just install the package and it gets all required libraries to convert and then burn's on the fly. And you won't believe how simple it is. I just want to a directory that had the MP3's I wanted t........
  • Install Mac OS X 10.4.6 Tiger on AMD32 VMWare


    *Note OS X is strange to install, I thought my HDD was not being detected by you just have to go to Diskutil and create a partition for the root filesystem and then close/move the Window and proceed with the install. After install Mac OS X 10.4.6 Tiger I get a black screen that says: b0 error Most people say the partition has to be marked as "active", actually that just means marked as "bootable". Instead of t........
  • FreeBSD detected my burners as normal CD-ROMs


    FreeBSD detected my burners as normal CD-ROMsDoes anyone know how to fix this?Having the same issue here .....I'll let you know once I solve it :)........
  • Hard Drive Not Working/Not Detected By Your BIOS Anymore?


    I was starting to panic because suddenly my 1TB Seagate SATA drive wasn't working,I thought it was a BIOS issue because it seemed to have happened after I tried overclocking my Desktop too much. I tried powering down and waiting, but I still couldn't hear the drive spin up at all. I tried a second 1TB hard drive and it wouldn't work either. I checked all power connections again and again until one of the pins in the MOLEX connector popped completely loose. Th........
  • Latest Articles

  • FreePBX 17 How To Add a Trunk
  • Docker Container Onboot Policy - How to make sure a container is always running
  • FreePBX 17 How To Add Phones / Extensions and Register
  • Warning: The driver descriptor says the physical block size is 2048 bytes, but Linux says it is 512 bytes. solution
  • Cisco How To Use a Third Party SIP Phone (eg. Avaya, 3CX)
  • Cisco Unified Communication Manager (CUCM) - How To Add Phones
  • pptp / pptpd not working in DD-WRT iptables / router
  • systemd-journald high memory usage solution
  • How to Install FreePBX 17 in Linux Debian Ubuntu Mint Guide
  • How To Install Cisco's CUCM (Cisco Unified Communication Manager) 12 Guide
  • Linux Ubuntu Redhat How To Extract Images from PDF
  • Linux and Windows Dual Boot Issue NIC Won't work After Booting Windows
  • Cisco CME How To Enable ACD hunt groups
  • How to install gns3 on Linux Ubuntu Mint
  • How to convert audio for Asterisk .wav format
  • Using Cisco CME Router with Asterisk as a dial-peer
  • Cisco CME How To Configure SIP Trunk VOIP
  • Virtualbox host Only Network Error Failed to save host network interface parameter - Cannot change gateway IP of host only network
  • Cisco CME and C7200 Router Testing and Learning Environment on Ubuntu 20+ Setup Tutorial Guide
  • Abusive IP ranges blacklist