Bonding is an excellent way to get both increased redundancy and throughput. It is similar to the "Network Teaming" feature in Windows.
There are a few different modes but we will use mode 6, I think it's the best of both worlds, as it is not just a failover, but it provides round robin, so you will get redundancy and load balancing. So if you have a 1G single port, you will have a combined throughput of 4G at this point. Just bear in mind that the true thr........
The Best Docker Tutorial for Beginners
We quickly explain the basic Docker concepts and show you how to do the most common tasks from starting your first container, to making custom images, a Docker Swarm Cluster Tutorial, docker compose and Docker buildfiles.........
A big problem over ssh and especially sshfs is that your connection will often timeout and disconnect after inactivity.
To fix this you can modify the server but it may not be practical or you may not have access. Why not send keep alives fom your end (client side)?
Just edit /etc/ssh/ssh_config (not to be confused with sshd_config as that is the server side):
Find the line that says "Host *" and change it like this:........
This is not about using ssh as a proxy, but rather, using a proxy when you are SSHing to another host and using ProxyCommand (where we normally use nc as our proxy tool).
In newer versions of nc the syntax has changed to the following:
ssh -o ProxyCommand="nc -x 127.0.0.1:1234" %h %p user@host
The format must be like above in newer nc versions.
Just be sure to change the 1234 to the port of your SOC........
Are you tired of coming back to your computer only to find your SSH connections have been broken? Even worse are the ones that hang where it appears to be connected but it is really not.
The one option you have is an SSHclient side modification to send KeepAlive packets, sometimes this can also keep up your WiFi connection and stop it from disconnecting you as well.
To make the keep alive changes for your just yourself (not system wide)........
user@box:~$ sudo tune2fs -l /dev/md99
[sudo] password for user:
tune2fs 1.42.9 (4-Feb-2014)
Filesystem volume name:
Last mounted on: /mnt/md50
Filesystem UUID: 976a8655-2619-4587-878c-dab07f7b7652
Filesystem magic number: 0xEF53
Filesystem revision #: 1 (dynamic)
Fi........
This happened while an mdadm array was syncing, all access from writing a new blank file to opening a small .txt file was very slow:
[222117.312078] kjournald starting. Commit interval 5 seconds
[222117.685060] EXT3-fs (md0): using internal journal
[222117.685096] EXT3-fs (md0): mounted filesystem with ordered data mode
[222122.376847] kjournald starting. Commit interval 5 seconds
[222122.602825] EXT3-fs (md2): using internal jour........
LSi Megaraid
At first it was configured as a RAID 0, then I deleted the Virtual Disk Group.
I thought both drives would be shown and detected in Linux as sda and sdb but it actually shows nothing.
To make them work you have to hit Ctrl+R before the system boots (when prompted) and create a Virtual Disk Group. In my case I created each one as RAID 0 (with a single drive only) as I just wanted JBOD but there is no such option or default in these Dell Pe........
You need to enable the httpd daemon with monit to actually view the status and control, it's not only for the web interface since the httpd is theONLY way of controlling monit and viewing the status.
monit monitor all will also reinstate disabled services if they've timed out too much. Just restarting the service will do nothing to re-monitor a service that monit has stopped monitoring due to too many failures.
*Also note that /etc/monit.conf i........
high IO wait
424 root 39 19 1900 848 552 D 0.0 0.0 0:00.91 updatedb
root 424 0.0 0.0 1900 848 ? DN Mar11 0:00 /usr/bin/updatedb -f sysfs?rootfs?bdev?proc?cpuset?binfmt_misc?debugfs?sockfs?usbfs?pipefs?anon_inodefs?futexfs?tmpfs?inotifyfs?eventp........
I separated the 2 drives in the RAID 1 array.
1 is the old one /dev/sda and is out of date, while the separated other one /dev/sdc was in another drive and mounted and used with more data (updated).
I wonder how mdadm will handle this:
usb-storage: device scan complete
md: md127 stopped.
md: bind
md: md127: raid array is not clean -- starting background reconstruction
raid1: raid set md127 active with 1 out of 2 m........
I have no idea why but mkfs.ext3 defaults to a patheticlly small blocksize of 1024 bytes/1KB (kilobyte). That means the maximum filesize is ONLY 16GB! With 2KB/2048 bytes you get a 256 GB maximum filesize, and with 4KB/4096 bytes you get 2TB!
I finally noticed/paid attention to this after realizing that with rsync and scp that no file larger than 17GB could be transferred. I then realized it must be a file size limit on the partition.
Here is what tune2fs tol........