• Cisco Unified Communications Manager Express Cheatsheet CUCME CME


    Getting started, let's enable ephones and DNs we can add a phone with a telephone number: Router>en Router#conf t Router(config)#telephony-service !this enables ephone registration otherwise phones cannot register Router(config-telephony)#ephone-reg !max-ephones 2 says we can have a maximum of 2 phones, change to your needs (or to the limit set by your IOS image) Router(config-telephony)#max-ephones 2 ........
  • SSH Keep Alive To stop Disconnections


    Are you tired of coming back to your computer only to find your SSH connections have been broken? Even worse are the ones that hang where it appears to be connected but it is really not. The one option you have is an SSHclient side modification to send KeepAlive packets, sometimes this can also keep up your WiFi connection and stop it from disconnecting you as well. To make the keep alive changes for your just yourself (not system wide)........
  • Cisco DHCP Snooping Relay Setup Information


    Switch#show ip dhcp snooping Switch DHCP snooping is disabled DHCP snooping is configured on following VLANs: 1 Insertion of option 82 is enabled circuit-id format: vlan-mod-port remote-id format: MAC Option 82 on untrusted port is not allowed Verification of hwaddr field is enabled Interface&nb........
  • Linux wlan0 check all wireless clients


    iw dev wlan0 station dump This is very useful because it is helpful if you are running something like hostapd and need to see the signal strength and negotiated connection speed. Station ff:ff:ff:ff:ff:ff (on wlan0) inactive time: 16309 ms rx bytes: 25451 rx packets: 325 tx bytes: 44381 tx packets: 159 tx retries: 0 tx failed: 0 signal: -72 [-72] dBm signal avg: -72 [-72] dBm........
  • iptables how to log ALL dropped incoming packets


    A lot of people just have a -j DROP to drop all unwanted traffic or traffic not explicitly allowed but there is a better solution if you want real and proper logging: Take an example iptables rules file -A INPUT -m state --state RELATED,ESTABLISHED -j ACCEPT -A INPUT -i eth1 -p icmp -j ACCEPT -A INPUT -i lo -j ACCEPT -A INPUT -i eth1 -j ACCEPT -N LOGGING -A INPUT -j LOGGING -A LOGGING -j LOG --log-pre........
  • wodim / cdrecord error cannot burn DVD or BDR .iso Errno: 5 (Input/output error), write_g1 scsi sendcmd: no error


    dvd+rw-mediainfo /dev/sr0 INQUIRY: [ASUS ][BW-16D1HT ][3.00] GET [CURRENT] CONFIGURATION: Mounted Media: 11h, DVD-R Sequential Media ID: RITEKF1&n........
  • OpenVPN cannot ping remote IP routing loop issue after connecting


    Sometimes if you have a very basic configuration OpenVPN on the client side for some reason sends all traffic to the OpenVPN server IP through the tun0 which is of course impossible and creates a block or routing loop. This is because you need to use your normal ISP/LANgateway to hit the OpenVPN server if it is remote/offsite as is usually the case. So if you are connected to the OpenVPN through say a tun0 device and your routing is set to connect to the OpenVPN&nbs........
  • Intel NUC J3455 Linux Kernel freeze slowness 4.4.98 errors


    It looks like this has something to do with APIC but I am not sure. I have similar CPUs with a different MB and BIOS that work fine on the same type of kernel. A lot of time the issue is because of the C-step setting in the BIOS. The same thing happened on the 2.6 kernel with Centos 6 but this is a homebrew 4.4 kernel soI am not sure why it is happening when even Centos 7 (3.2) kernel works OK. Solution - It comes down to the BIOS set........
  • ERROR 2006 (HY000) at line 567: MySQL server has gone away


    mysqldump or mysql query of a larger file/table ERROR 2006 (HY000) at line 567: MySQL server has gone away Add this to /etc/my.cnf max_allowed_packet=64M service mysqld restart........
  • l2tp ipsec VPN Error Sep 12 18:16:25 vps pluto[7299]: ERROR: asynchronous network error report on eth0 (sport=500) for message to 192.5.6.2 port 20640, complainant 192.5.6.2: Connection refused [errno 111, origin ICMP type 3 code 3 (not authenticated


    Sep 12 18:16:25 vps pluto[7299]: ERROR: asynchronous network error report on eth0 (sport=500) for message to 192.5.6.2 port 20640, complainant 192.5.6.2: Connection refused [errno 111, origin ICMP type 3 code 3 (not authenticated)] Some say changing the "leftprotoport=17/%any" will fix this but I have not found this to be the case. Essentially it means at least one end is blocking the ipsec packets. Sometimes the %any allows an alt........
  • Track 01: 34 of 1726 MB written (fifo 100%) [buf 99%] 3.6x.Errno: 5 (Input/output error), write_g1 scsi sendcmd: cmd timeout after 1.897 (40) s CDB: 2A 00 00 00 44 A9 00 00 1F 00 resid: 6144 cmd finished after 1.897s timeout 40s write track da


    These errors believe it or not are simply because of not being the root user or running with sudo! However if you didn't know to try as root you'd think there was a problem with your burner or disc Essentially it looks like without root you cannot send the required scsi commands to continue writing. Ithink cdrecord should have built-in tests or safeguards to see if it has the permissions to run the required commands. I guess for more advanced users the idea is simila........
  • Unable to mount location Failed to retrieve share list from server: No such file or directory solution


    Cannot even "Browse Network" when clicking on "Windows Network" Unable to mount location Failed to retrieve share list from server: No such file or directory logs: [2017/02/14 00:16:44.271314, 0] ../source3/nmbd/nmbd.c:58(terminate) Got SIGTERM: going down... [2017/02/13 17:35:41.797944, 0] ../lib/util/become_daemon.c:124(daemon_ready) &........
  • astrachat connection problems in Android 5.01 Lollipop


    I wanted to use Astrachat because it seems to be the only app that has video, pic and file sharing for Jabber butI cannot even connect despite any other client working fine including Xabber and others. astrachat "Oops.. We can't connect to the account that you provide above. Please recheck your account detail". Unfortunately to make it worse there doesn't seem to be any error log or more details about the issue. The jab........
  • Linux Mint Network Manager Connection Disconnect Option Grayed Out


    This is a real pain because I had to manually unplug ethernet cables for network testing or to use an alternate network or guarantee physical access to one network segment is cut off. For some reason this happened after Ikilled dbus because it was confused and blocking packets thinking they were coming from the wrong interface since eth0 and eth1 both had the same subnet and gateway. I eventually did a "service network-manager restart" but the option was........
  • Debian 8 Jessie in Linux OpenVZ Container does not work on Centos host


    It sounds like this is corrected in later versions of the OpenVZ kernel but Iam not sure, it may also be that a much newer kernel is needed and Centos may not have a recent enough kernel. *Debain 7.0 however does work fine as a temporary fix or work around. Debian 8 OpenVZ no IP and networking not working: lo Link encap:Local Loopback  ........
  • nf_conntrack: table full, dropping packet solution


    nf_conntrack: table full, dropping packet The above in some cases I've seen is a sign of a DOS attack or can occur if users are using services like torrenting, proxy, VPNetc... Do not take it lightly as the above can knock a server offline if the table becomes full and I've also seen full crashes and kernel panics shortly after. ........
  • eth0 changed to eth1 or eth2 and the solution to fix it


    If you move your hard drive(s) around to other computers/servers, you'll find that your eth0 keeps getting higher, the first time it will become eth1 and then eth2 etc and even higher if your server has dual or quad NICs. The reason is that udevd basically assigns eth0 tot he first NIC it finds and remembers it, if it encounters a NIC with a differentMAC, it assigns it one higher (eg. eth1). See the example below, I have eth2 now so how doI fix it?........
  • ip_conntrack: table full, dropping packet. solution for Linux RHEL/Centos/Debian


    ip_conntrack: table full, dropping packet. A lot of clients I've seen have this issue, it really seems the default level is way too small. Once this connection tracking table becomes full then packets get dropped which is obviously a bad thing. One thing to be mindful of though is that 350 bytes of memory are used per entry so there is some justification for not keeping it too high. However, if you have multiple servers running or high traffic daemons........
  • pcnet32: eth0: transmit timed out, status 97fb, resetting - NIC card problem solution


    I've encountered this problem before and I believe it may affect other drivers (I could test but I don't have time). This was happening on my custom Linux system with the pcnet32 driver. pcnet32: eth0: transmit timed out, status 97fb, resetting (and some other kernel module tracing in dmesg) Basically it means the card is connected (it shows connected in full duplex etc.. and recognized if the cable is disconnected too) but no packets can be sent or received........
  • How To Burn ISO Image using cdrtools/dvdrtools for Linux/Unix Ubuntu/Debian/RHEL/Centos etc..


    It really is as simple as: cdrecord -v dev=/dev/sr0 pathtoyourisoimage.iso -v is for verbose, I prefer it but if you don't you won't see as much output like below (I like to know the details and exactly what's happening) dev=/dev/sr0 specifies the device name of your burner (they say not to use it and to specify some weird annoying device string but using the raw /dev has always worked for me and is how it should have been implemented from the start IMHO)........
  • How to view UDP and other protocol connections?


    netstat is weak and can't show udp connections and most other protocols, use "ss" which is what netstat should have been: The "-u" switch stands for udp, here's a list of other options: Usage: ss [ OPTIONS ] ss [ OPTIONS ] [ FILTER ] -h, --help this message -V, --version output ver........
  • Linux Burn MP3 CD On the Fly using


    I finally decided to look into some utils that did this, and the first one I found is "mp3burn". It is unbelievable simple and perfect. *2017-11 update and mp3burn is still available in standard repos such as Ubuntu 14/16 so this is a current and working project. Just install the package and it gets all required libraries to convert and then burn's on the fly. And you won't believe how simple it is. I just want to a directory that had the MP3's I wanted t........
  • Telus + 2Wire 2700 Router Horrible


    Telus + 2Wire 2700 Router HorribleWell first of all let me say this is the only router/switch that sometimes seems to crash/disconnect computers on the local network. This device also thought it would be smart to block VOIP packets coming from my Sipura ATA VOIP adapters so I disabled the [quote:cb89ba7bff]"Invalid TCP Flag Attacks (NULL/XMAS/Other)"[/quote:cb89ba7bff] option Then all of a sudden I couldn't get onto any web pages, the wireless........
  • OCFS2 crash


    When trying to even cd or ls the mounted OCFS2 partition it crashes. Ithink this is a combination of VMWare Server's problem and the way I mounted and symlinked to it. More than anything this shows the problem and lack of forsight with VMWare, but also that OCFS2 is easily crashed if you do strange things. Output of /var/log/messages for OCFS2 Apr 10 15:57:45 localhost kernel: [84331.691258] Modules linked in: vmnet vmci vmmon ocfs2_stac........
  • Latest Articles

  • qemu 4 compilation options
  • CentOS 7 8 PXEBoot Netinstall Not Working Solution "Pane is dead "new value non-exisetnt xfs filesystem is not valid as a default fs type"
  • CentOS 6 EOL yum repo won't work Error: Cannot find a valid baseurl for repo: base Solution
  • CentOS 7 8 How To Disable SELinux
  • Wordpress How To Add Featured Image To Post in Hueman Theme
  • kdenlive full reset how to erase all config files
  • CentOS 7 8 yum error Trying other mirror. To address this issue please refer to the below wiki article
  • Microsoft Teams Linux - Calendar Doesn't Work Missed Meetings!
  • Scanner not working in Linux Ubuntu Fedora Mint Debian over the network? Use sane-airscan!
  • How To Boot, Install and Run Windows 2000 on QEMU-KVM
  • bash cannot execute permission denied
  • Huion and Wacom Tablets How To Install in Linux Mint / Ubuntu and make the stylus work properly
  • ffmpeg how to cut certain parts of video out
  • ffmpeg how to concat and join two video clips
  • mencoder instead of ffmpeg to join or concatenate video files with different audio streams
  • Linux How To Stop Missing Drive from Halting Boot Process in fstab
  • How To Replace Audio Track of Video using ffmpeg
  • qemu-img convert formats vdi vmdk raw qcow2
  • Linux and Windows Dual Boot Crazy Time Issues
  • dynagen / dynamips 100% high CPU usage solution - how to set the idlepc value