The strange thing is that usually the first install or two will work on any new machine but then it suddenly won't. I had this experience on QEMU 2.13 on a different machine. There is something finicky or buggy about the CUCM installer even when choosing the same virtual hardware specs.
QEMU PC emulator version 0.12.1 (qemu-kvm-0.12.1.2-2.506.el6_10.1), Copyright (c) 2003-2008 Fabrice Bellard
You may get this after a long time of not rebooting but especially if you have rsync'd a / partition or deployed an image to another VPS or computer, you will often have this issue.
The good thing it usually just takes a reboot.
Here is more info from Centos........
Here is the scenario you or a client have a remote machine that was installed as a standard/default minimal Centos 6.x machine on a single disk with LVM for whatever reason. Often many people do not know how to install it to a RAID array so it is common to have this problem and why reinstall if you don't need to? In some cases on a remote system you can't easily reinstall without physical or KVM access.
So in this case you add a second physical or disk or already ha........
In my case I could login with the initial install but I rsync'd everything over while preserving ownership and permissions to another RAID partition and booted from that.was fine before. The problem is that you are kicked out the second you login and the problem was SELINUX for some reason (perhaps it noticed something strange when it was moved to the new partition)
login: pam_unix(login:session): session opened for user root by LOGIN(uid=0)
login: ROOT LOG........
yum -y install wget
wget -P /etc/yum.repos.d/ http://ftp.openvz.org/openvz.repo
rpm --import http://ftp.openvz.org/RPM-GPG-Key-OpenVZ
yum -y install vzkernel vzctl
sed -i s/'net.ipv4.ip_forward = 0'/'net.ipv4.ip_forward = 1'/g /etc/sysctl.conf
#all interfaces should not send redirects
echo "net.ipv4.conf.default.send_redirects = 1" >> /etc/sysctl.conf
i337 Canada on Bell is hard to root or even install TWRP
Installed TWRP from Odin and my computer gave me the bluescreen at the end but it seemed to be successful (after ODIN said reset).
TWRP mode does not seem to enter, instead you get the Android recovery mode with Volume up + Home
#count=10000 makes an image of 10000MB make sure your image is at least the same as your existing
dd if=/dev/zero of=yourimage.img bs=1M count=10000
# losetup -fv newimage.raw
# fdisk -cu /dev/loop0
# kpartx -a /dev/loop0
# dd if= of=/dev/mapper/loop0p1
# e2fsck -f /dev/mapper/loop0p1
# resize2fs /dev/mapper/loop0p1
# a lot of guides tell you to edit /etc/fst........
mount -o bind /proc /sda2/proc
mount -o bind /dev/ /sda2/dev
mount -o bind /sys /sda2/sys
mint / # mount -o bind /proc /sda2/proc
mint / # mount -o bind /dev/ /sda2/dev
mint / # mount -o bind /sys /sda2/sys
mint / # chroot /sda2
mint / # cd ~
mint ~ # ls
mint ~ # cd /
mint / # ls
bin Desktop dev-temp home&nb........
After some fsck issues I can't boot my Centos 6.4, this just keeps repeating over and over.
init: tty (/dev/tty2) main process (1031) terminated with status 1
init: tty (/dev/tty2) main process ended, respawning
Disabling SELinux through Single User mode fixed this.........
Kernel panic - not syncing: Attempted to kill init!
Pid: 1,comm: init Tained: G I------------- 2.6.32-358.el6.x86_64 #1
 ? panic+0xa0/0x16f
 ? do_exit+0x862/0x870
 ? fput+0x25/0x30
 ? do_group_exit+0x58/0xd0
 ? sys_exit_........
Solution To The Following:
yum -y install zlib-devel
yum -y install e2fsprogs*
*** Cannot find /usr/include/et/com_err.h. (yum install libcom_err-devel) ***
Installation didn't pass, halting install.
Once requirements are met, run the following to continue the install:
Common pre-install commands:
Here is a quick script that works on most Centos versions to disable the virus/SELinux from blocking basic functionality.
The first echo 0 statement disables SELinux instantly but it will still be enabled on reboot.
The second line disables it permanently.
#disable SELinux Immediately
echo 0 > /selinux/enforce
#disable SELinux Permanently
sed -i 's/SELINUX=enforcing/SELINUX=disabled/g' /etc/selinux/config........
yum exits in the middle
The problem is this VPS seems to be an OpenVZ template from HyperVM. The only way to make it work was to disable i386 packages since this was an x64 kernel. That shouldn't be necessary but it was the only way to make yum stop quitting after the first package or two. I couldn't find any issue by checking the logs either.
echo y|yum install vim-minimal telnet expect jwhois net-tools slocate iptables elinks gawk
This is a very simple solution, but most guides out there make you login twice (once to scp the key) and once to put the key in authorized_keys. There's no need for that.
If you don't already have a ~/.ssh/id_rsa.pub just type "ssh-keygen -t rsa" and keep hitting enter until it's done :)
Just use this code to easily enable passwordless login with SSHD
key=`cat ~/.ssh/id_rsa.pub`;ssh email@example.com "echo $key >> ~/.ssh/auth........
I decided on using yum to help me decide even though I normaly use proftpd I decided to see what else I could find.
yum search ftp
Loaded plugins: fastestmirror
Loading mirror speeds from cached hostfile
* rpmforge: ftp-stud.fht-esslingen.de
* base: mirrors.netdna.com
* updates: updates.interworx.info
* addons: yum.singlehop.com
* extras: mirrors.netdna.com