A lot of times I've seen questions about how this works when you have multiple nodes or a CDN, it can be quite tricky in theory if you have random IPs or several IPs. The way certbot works at least for non-DNS challenges is that it will hit a random server that it resolves to, you have no control over which one it hits. If certbot hits node 1 at first to tell it to create the well-known file, then checks node 2 or any other node, you will find auhorization fails.........

In our example below, we create 2 hunt groups. You could assume the #1 group is sales and #2 group is support etc.. and you can create more as needed. The main part of hunt is the "list" option where you add each phone number that is to be part of the group ephone-hunt 1 sequential pilot 2001 list 1234 timeout 10 ephone-hunt 2 sequential pilot 2002 list 5678 tim........

In our example we take "sound.mp3" and convert it to .wav. Generally Asterisk for its wave needs one audio channel (-ac 1) / mono and 8000hz (-ar 8000) instead of the standard CD/MP3 of 44100hz. Here is the command to convert into Asterisk .wav format: ffmpeg -i sound.mp3 -ac 1 -ar 8000 sound.wav Errors Asterisk may give you if the format is wrong: -- Executing [91781891@cme:3] Playback("SIP/234-000........

#Remember that you need a valid gateway IPunless the Asterisk server is on the same subnet and LAN Set Valid Gateway IP (if you don't have one already) ip route 0.0.0.0 0.0.0.0 GATEWAYIP Enable VOIPTrust voice service voip ip address trusted list ipv4 0.0.0.0 0.0.0.0 sip Set Credentials For Asterisk and Register To Asterisk sip-ua........

This is how we configure outside PSTNaccess or dialing through another SIPtrunk. Beware that this a simplistic example that neglects most security including SRTP First you'll need to be in config mode: Step - 1 Enter Voice Service VOIP security options There are more options but for now we'll just focus on security/allowing connections to and from our phones and the trunk. Router(config)#voice service voip ........

Since newer versions of Ubuntu like 20, you will find there is no longer dynagen and that the dynamips provided is faulty and will segfault each time: Cisco Router Simulation Platform (version 0.2.14-amd64/Linux stable) Copyright (c) 2005-2011 Christophe Fillot. Build date: Apr 3 2018 12:20:29 Local UUID: 3c1c0b7f-2fab-4fda-b40b-74841d1bcfe0 Instance ID set to 1. netio_tap_create: unable to open TAP device tap1 (No such fi........

Just hit **# on the keypad and the CIPCwill enable the button in settings for a factory reset. Sometimes the phone may run into issues or may be unable to register to another tftp server (eg. another CME or CUCM server) due to a bug or maybe due to the security settings tying it to a specific server. Step 1 - Click Settings Step 2 - Hit "**#"........

Router#show license Index 1 Feature: ipbasek9 Period left: Life time License Type: Permanent License State: Active, In Use License Count: Non-Counted Lic........

With ffmpeg it literally takes out what you want so you can use it later. Eg. below -ss means starting time is 16 minutes and 30 seconds and -to means extract until 17 minutes and 23 seconds -i = the input file output file = CCME-flash-and-2-phone-setup-final.mp4 ffmpeg -i CCME-flash-and-2-phone-setup.mp4 -ss 00:16:30 -to 00:17:23 -c copy CCME-flash-and-2-phone-setup-final.mp4 How to spec........

This normally works but if not use my mencoder solution if the output video does not play past the joined time. the contents of list.txt need to look like this: file somefile.mp4 file somefile2.mp4 then run ffmpeg ffmpeg -f concat -i list.txt -c copy CME-2-router-dial-peer-final.mp4 The result is almost instant joining since there is no video processing since we are........

The problem for me is that Ihad two videos with different types of audio streams. ffmpeg would join them but they would not play past the point of the join. So Iused mencoder like below and it joined the audio and made them both mp3 streams and it worked! -oac mp3lame specifies the audio to be convered into an mp3 stream using the lame codec. after the oac the two files are the ones to be joined. the -o is the name of the outp........

This tutorial will get your router up and running using emulation tools. In this case we'll be getting a Cisco C7206 (C7200 series) VXR router going which also supports SCCP VOIP services. dynamips is the emulator itself and dynagen is the front-end tool that helps us control everything. It is used by tools such as gns3 and eve-ng. Together the two tools (dynamips and dynagen) allow us to create and emulate REAL router........

Video Links: How To Setup 2 Phones on a Single CME Router and get the GUI going. How to use Dialpeers with CME with two routers How to implement call restrictions using COR / Class of Restriction Set your clock: HH:MM:SS clock set 22:00:00 24 September 2024........

The strange thing is that usually the first install or two will work on any new machine but then it suddenly won't. I had this experience on QEMU 2.13 on a different machine. There is something finicky or buggy about the CUCM installer even when choosing the same virtual hardware specs. qemu-kvm command: /usr/libexec/qemu-kvm -version QEMU PC emulator version 0.12.1 (qemu-kvm-0.12.1.2-2.506.el6_10.1), Copyright (c) 2003-2008 Fabrice Bellard ........

For some reason, perhaps you don't want to run a daemon or let Letsencrypt have access to your production server. There is a way to use it like a normal CSR/CA setup in manual mode. ./letsencrypt-auto certonly --manual -d realtechtalk.com - www.realtechtalk.com   Eventually you will get prompted to create a certain path and file with certain data: Create a file containing just this data: Casdfasfadsfsad........