• Cisco 2960 Switch Reset To Factory Defaults


    *The easy way is to just hold the mode button for 10+ seconds. The full/proper way is below: 1.) Either power on the unit and hold the "mode" button or hold the "mode" button until you see the below: 00:04:08: %SYS-7-NV_BLOCK_INIT: Initalized the geometry of nvram 00:04:08: %EXPRESS_SETUP-6-CONFIG_IS_RESET: The configuration is reset and the system will now reboot 00:04:09: %SYS-5-REL........
  • DRBD Errors Caused By Physical Corruption


    In a RAID array I had a have periodically lost a drive here and there over the past several months. Iwas always able to readd and resync without losing data. However at some point it looks like some minor corruption happened and this makes DRBD unhappy. Using fsck did not help either. Dec 19 06:01:45 storageboxtest4 kernel: [19005.945890] EXT3-fs error (device drbd0): ext3_get_inode_loc: unable to read inode block - inode=22184379........
  • LSI MegaRAID Adventures, Guide and HowTo


    LSi Megaraid At first it was configured as a RAID 0, then I deleted the Virtual Disk Group. I thought both drives would be shown and detected in Linux as sda and sdb but it actually shows nothing. To make them work you have to hit Ctrl+R before the system boots (when prompted) and create a Virtual Disk Group. In my case I created each one as RAID 0 (with a single drive only) as I just wanted JBOD but there is no such option or default in these Dell Pe........
  • WD 20EARX 2TB Bad within days


    This is just trying to read 5GB off the drive with dd and the drive initially tested ok but shortly after I wondered why I was seeing 2MB/s read speeds. Notice the "current_pending_sector", anytime I've seen it at anything above 0 even with no other bad fields/attributes, it means the drive is bad. ata1.00: exception Emask 0x0 SAct 0x3 SErr 0x0 action 0x0 ata1.00: irq_stat 0x40000008 ata1.00: failed command: READ FPDMA QUEUED ata1.00: cmd 60/00:00:........
  • OpenVZ/vzctl how to do an on-line migration without downtime


    vzmigrate --online dest-host VEIDNO eg.: vzmigrate --oneline 192.168.1.55 101 One option I would recommend is "--keep-dst", that way if the migration is interrupted you can still bring the VPS back up on the original host. After the migration is successful you can manually destroy it. OpenVZ has a good writeup on this including Checkpointing and Restoring etc:........
  • GRUB "Error 2: Bad file or directory type" 0.97 won


    You can see the problem below, GRUB recognizes my hard drive and sees the partitions but cannot access them. This is from the GRUB boot disc I'm using. What happened is that I had some power issues causing this system's power to be interrupted several times and basically an on/off on/off situation. The system won't boot, I just get a flashing cursor and no message or error from GRUB. Obviously the problem is that my MBR seems corrupt or some other issue. My........
  • Latest Articles

  • Linux tftp listens on all interfaces and IPs by DEFAULT Security Risk Hole Solution
  • python import docx error
  • Cisco Unified Communications Manager Express Cheatsheet CUCME CME
  • Linux Ubuntu Debian Missing privilege separation directory: /var/run/sshd
  • bash how to count the number of columns or words in a line
  • bash if statement how to test program output without assigning to variable
  • RTNETLINK answers: Network is unreachable
  • Centos 7 how to save iptables rules like Centos 6
  • nfs tuning maximum amount of connections
  • qemu-kvm error "Could not initialize SDL(No available video device) - exiting"
  • Centos 7 tftpd will not work with selinux enabled
  • Debian Ubuntu Mint Howto Create Bridge (br0)
  • How To Control Interface that dhcpd server listens to on Debian based Linux like Mint and Ubuntu
  • LUKS unable to type password to unlock during boot on Debian, Ubuntu and Mint
  • Debian Ubuntu and Linux Mint Broken Kernel After Date - New Extra Module Naming Convention
  • Wordpress overwrites and wipes out custom htaccess rules and changes soluton
  • Apache htaccess and mod_rewrite how to redirect and force all URLs and visitors to the SSL / HTTPS version
  • python 3 pip cannot install mysql module
  • QEMU-KVM won't boot Windows 2016 or 2019 server on an Intel Core i3
  • Virtualbox vbox not starting