Remember that control connections are established on port 1723 and then actual data is transferred over GRE protocol 47. If you have a NAT setup this will work without special forwarding or accepting of GRE packets (normally if you are not blocking outgoing connections and accepting established and related connections). The below two commands will get things going so PPTP and GRE work We first load the ip_nat_pptp module which allows PPTP to work with........

Just a quick note and warning is that if you are testing to see if EFIPXE booting works on a VM, MAKE SURE it actually works. For example Iinitially tested using my Distro's QEMU 2.5+dfsg-5ubuntu10.46 and ovmf BIOS firmware (OVMF supports EFI). However, I found on old versions of QEMU (like 2.5), EFIbooting with GRUB NEVER works so it may appear that you have made a mistake when everything is fine when you boot a physi........

mdadm --create /dev/md0 --level 1 --raid-devices 2 /dev/sdb1 missing --metadata=0.90 mdadm: super0.90 cannot open /dev/sdb1: Device or resource busy mdadm: /dev/sdb1 is not suitable for this array. mdadm: create aborted Sometimes running "partprobe" can fix this. Other times it requires a reboot. One other manual thing that can be done is the following to fix it (if dm is using and blocking it):........

This is a gotcha but be aware sometimes iptables may be active and loaded by default. Also make sure you don't just disable firewalld but also stop it otherwise it will still block stuff: systemctl stop firewalld If the above is not the issue then it is possible iptables is running and blocking stuff too, so you'll need to stop iptables. So in addition to opening firewalld or disabling it, you would need to disable iptables........

Idid a systemctl restart networking and it broke Proxmox VM connectivity! #proxmox is the problem after restarting the network the tap devices go to disabled state [2230884.919905] vmbr0: port 7(tap118i0) entered disabled state [2230884.948864] vmbr0: port 8(tap122i0) entered disabled state [2230884.972748] vmbr0: port 6(tap119i0) entered disabled state [2230885.004745] vmbr0: port 5(tap117i0) entered disabled state [2230885.03673........

GRANT SELECT, LOCK TABLES ON *.* TO yourmysqluser@localhost; All you need to do a full MySQL dump on all databases is the SELECT and LOCK TABLES privileges. This way you don't have to use the mysql root user. Data could be compromised this way but at least no harm from manipulation, changes or deletion are possible by locking down the privileges to the minimum for a full MySQL dump and backup.........

The Linux Kernel interpretated a very high volume of real traffic as a DDOS attack so it basically ends up blocking your web server. possible SYN flooding on ctid 42131, port 80. Sending cookies. Simple fix edit sysctl values for max_syn_backlog sysctl -w net.ipv4.tcp_max_syn_backlog=5000 To make them permanent edit /etc/sysctl.conf echo "net.ipv4.tcp_........

Sep 12 18:16:25 vps pluto[7299]: ERROR: asynchronous network error report on eth0 (sport=500) for message to 192.5.6.2 port 20640, complainant 192.5.6.2: Connection refused [errno 111, origin ICMP type 3 code 3 (not authenticated)] Some say changing the "leftprotoport=17/%any" will fix this but I have not found this to be the case. Essentially it means at least one end is blocking the ipsec packets. Sometimes the %any allows an alt........

The solution is simple but strange, if you copy your /var/lib/mysql directory to another server and think it will work, be sure to check if you have /var/log/mysql and binary log files. If you do, the server will not work and will give you errors like below and crash without the proper log files. UPDATE user SET password=password("newpass") WHERE user='root'; flush privileges; ERROR 2013 (HY000): Lost connection to MySQL server durin........

This is a real pain because I had to manually unplug ethernet cables for network testing or to use an alternate network or guarantee physical access to one network segment is cut off. For some reason this happened after Ikilled dbus because it was confused and blocking packets thinking they were coming from the wrong interface since eth0 and eth1 both had the same subnet and gateway. I eventually did a "service network-manager restart" but the option was........

The solution is to run '/etc/init.d/vboxdrv setup' and sometimes happens when upgrading VBox and the kernel modules don't get upgraded with it. Sometimes the above doesn't work until you reboot because sometimes other unknown processes (even the file manager possibly) may be locking the old module from being unloaded. Failed to open a session for the virtual machine XP. The virtual machine 'XP' has terminated unexpectedly during startup with exit code 1.........

relay=alt4.gmail-smtp-in.l.google.com. [74.125.136.26], dsn=4.0.0, stat=Deferred: 421-4.7.0 [ 10] Our system has detected an unusual rate of This is strange because the mail server IP is not blacklisted anywhere and the IP itself has not been used for years and this server is clean and has only sent a few e-mails to gmail.com in its entire time. I wonder if this is a legacy block on a whole range of IPs as punishment for others in the block........

Here is a quick script that works on most Centos versions to disable the virus/SELinux from blocking basic functionality. The first echo 0 statement disables SELinux instantly but it will still be enabled on reboot. The second line disables it permanently. #!/bin/bash #disable SELinux Immediately echo 0 > /selinux/enforce #disable SELinux Permanently sed -i 's/SELINUX=enforcing/SELINUX=disabled/g' /etc/selinux/config........

For years I've always built cheap systems believing that there is little difference in more expensive components when it comes to reliability and quality, I generally believe this still except for Power Supplies. I've always bought cheap cases with nice sounding 350-550W stock/cheap/crap power supplies and haven't had any issues for the most part until recently. One such case is an NGEAR case with a 550W Optimax power supply, I always read that these supplies don't produce the........

dd if=/dev/sda of=/dev/null creates ever increasing load every second. After minutes the load has moved up to 4.79 I've tried with two different discs in my system. I wonder if it's a delay or problem with the SATA bus because one drive I have connected has recently failed. I notice when drives fail that you get some IO/blocking issue when they don't respond properly. Yes I believe it was, because here's the same disc after removing the dead........

This has stumped me a few times because I keep forgetting that Centos 5.5 comes with a default iptables configuration that ends up blocking DRBD traffic,I tried all the normal things and couldn't understand why I couldn't make my normal DRBD config work. So if you have WFConnection problems and have tried the normal "mailing list" fixes, check your firewall status first! Both Nodes Say the Following: version: 8.3.8 (api:88/prot........

I was starting to panic because suddenly my 1TB Seagate SATA drive wasn't working,I thought it was a BIOS issue because it seemed to have happened after I tried overclocking my Desktop too much. I tried powering down and waiting, but I still couldn't hear the drive spin up at all. I tried a second 1TB hard drive and it wouldn't work either. I checked all power connections again and again until one of the pins in the MOLEX connector popped completely loose. Th........