• iSCSI on Centos 7 Configuration and Setup Guide for Initiator and Target


    initiator = client target = server These are the first concepts you should understand which is that in iscsi essentially the "initiator" is the client and the "target" is the server. iSCSI is derived from the old fashioned SCSI that us oldtimers grew to love. The "i" stands for Internet and the SCSI stands for "Small Computers Systems Interface" (SCSI). iSCSI Target (Server)Setup targetcli is the pac........
  • systemd management using systemctl and journalctl to check systemd logs


    systemd is like the service manager for your Centos and other modern Linux distributions (including Debian/Mint/Ubuntu) allows you to enable services, stop them, restart them, check their status and even reboot your system. The key commands or arguments you will use with systemctl are the following: Unit Commands: list-units [PATTERN...] List loaded units &nbs........
  • Intel NUC J3455 Linux Kernel freeze slowness 4.4.98 errors


    It looks like this has something to do with APIC but I am not sure. I have similar CPUs with a different MB and BIOS that work fine on the same type of kernel. A lot of time the issue is because of the C-step setting in the BIOS. The same thing happened on the 2.6 kernel with Centos 6 but this is a homebrew 4.4 kernel soI am not sure why it is happening when even Centos 7 (3.2) kernel works OK. Solution - It comes down to the BIOS set........
  • mcp55 NIC not working at boot on Centos 6.6-6.8


    forcedeth 0000:00:08.0: irq 25 for MSI/MSI-X forcedeth 0000:00:08.0: eth0: MSI enabled forcedeth 0000:00:08.0: eth0: no link during initialization ADDRCONF(NETDEV_UP): eth0: link is not ready forcedeth 0000:00:08.0: eth0: link up ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready Dec 1 18:21:32 box15 kernel: forcedeth: Reverse Engineered nForce ethernet driver. Version 0.64. Dec 1 18:21:32 box15 kernel........
  • blocked for more than 120 seconds issues with iowait and timeout on Live Linux distribution while writing to physical disk


    This happened while an mdadm array was syncing, all access from writing a new blank file to opening a small .txt file was very slow: [222117.312078] kjournald starting. Commit interval 5 seconds [222117.685060] EXT3-fs (md0): using internal journal [222117.685096] EXT3-fs (md0): mounted filesystem with ordered data mode [222122.376847] kjournald starting. Commit interval 5 seconds [222122.602825] EXT3-fs (md2): using internal jour........
  • WD 20EARX Dead Again


    Another new drive bad from the start: Jun 2 15:14:18 one-desktop kernel: [15895.386779] ata2.00: exception Emask 0x50 SAct 0x1 SErr 0x280900 action 0x6 frozen Jun 2 15:14:18 one-desktop kernel: [15895.386782] ata2.00: irq_stat 0x08000000, interface fatal error Jun 2 15:14:18 one-desktop kernel: [15895.386784] ata2: SError: { UnrecovData HostInt 10B8B BadCRC } Jun 2 15:14:18 one-desktop kernel: [15895.386788] ata2.00: cmd 60/0........
  • WD 20EARX 2TB Bad within days


    This is just trying to read 5GB off the drive with dd and the drive initially tested ok but shortly after I wondered why I was seeing 2MB/s read speeds. Notice the "current_pending_sector", anytime I've seen it at anything above 0 even with no other bad fields/attributes, it means the drive is bad. ata1.00: exception Emask 0x0 SAct 0x3 SErr 0x0 action 0x0 ata1.00: irq_stat 0x40000008 ata1.00: failed command: READ FPDMA QUEUED ata1.00: cmd 60/00:00:........
  • Bad Hard Drive Slows Down Computer


    Here's a proven example of what a bad hard drive can do, it was technically functioning OKin a RAID array but the system became extremely low and the load become high and IOWAIT was even higher and I always thought it was a bad application. The truth is that this failing 1TBHitachi has slowly gotten worse and caused huge slowdowns, (eg. 100% load on Thunderbird waiting for e-mails to load etc..). After swapping it out, tabs change instantly, emails are not lagged, and........
  • How to view UDP and other protocol connections?


    netstat is weak and can't show udp connections and most other protocols, use "ss" which is what netstat should have been: The "-u" switch stands for udp, here's a list of other options: Usage: ss [ OPTIONS ] ss [ OPTIONS ] [ FILTER ] -h, --help this message -V, --version output ver........
  • How To Test If Your Hard Drive Is Good/Signs of dying hard drive


    I like dd, although it only reads it, usually a read test of the entire disk will uncover if your hard drive is bad in some parts. This is a good thing to do at least once a month, a lot of times bizarre program behavior, laginess and crashing/unnmounting problems etc.. are due to a failing disc and SMART won't know it or indicate a problem: We must also remember there's never a guarantee, I've found that ever since we moved to larger and more platters per drive with 1TB drives........
  • smart is not smart, it thinks a dead drive is still good


    I had a dying drive that smart thought until it totally disappeared was a good drive, and actually all parameters did look fine but this system was causing my system to lockup and other bad behavior: === START OF INFORMATION SECTION === Device Model: WDC WD20EARS-00MVWB0 Serial Number: WD-WMAZ20139 Firmware Version: 50.0AB50 User Capacity: 2,000,398,934,016 bytes Device........
  • Hitachi 2TB HDS5C3020ALA632 drive DOA


    I had one of these shipped and it was not recognized when plugged in, here's what a dead drive looks like (I assume it's teh circuit board which is dead): ata1: link is slow to respond, please be patient (ready=0) ata1: softreset failed (device not ready) ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata1: link online but device misclassified, retrying ata1: link is slow to respond, please be patient (ready=0) ata1: softreset f........
  • CPU #1 not responding - cannot use it.


    I think this will be useful to others because I have a server that kept crashing mysteriously during intense disk usage/RAID checks. It would only crash during the weekly RAID integrity check. ThenI noticed during a reboot that not all CPUs were being brought up, as a result this actually creates much higher temperatures with the output I got from sensors, just booting the system produced higher than normal temperatures. You can imagine that a full blown RAID check........
  • Ubuntu 9.04 Crash


    CPU/Kernel/MB/RAID problem? Jan 5 12:45:05 testbox kernel: [653298.890004] BUG: soft lockup - CPU#0 stuck for 61s! [hal-acl-tool:4168] Jan 5 12:45:05 testbox kernel: [653298.890005] Modules linked in: vmnet vmci vmmon binfmt_misc drbd video output input_polldev ocfs2_stackglue ocfs2_dlmfs ocfs2_dlm ocfs2_nodemanager configfs k8temp hwmon_vid lp snd_hda_intel snd_pcm_oss snd_mixer_oss snd_pcm snd_seq_dummy snd_seq_oss snd_seq_midi snd_rawmidi........
  • WD (Western Digital) Advanced Format Drive Lagged/Slow Speed/Performance/Design Flaw EAD/EARS problem WDC WD20EARS-00S8B1


    Let the numbers speak for themselves, from what I read the Load_Cycle_Count which is very high (more than 500,000/half a million times) is the number of head parks. What a stupid"Green" design and design flaw which will probably mean an early life for the drive. This is almost as silly as Seagate's new reputation for BSY/poor quality disks since the 7200.11 series. To make it worse this is also when Western Digital introduced "Advanced Format" o........
  • Realtek r8169 1gbit/1000mbit NIC/Ethernet Goes Down/Halts on Large File Transfer/Heavy Network Usage


    This is obviously a bug in the r8169 kernel module and it seems to affect a lot of people. I upgraded to the latest kernel and hope this won't happen anymore, as it is a very serious error. This is especially serious for those who are running servers with this chipset, who can afford for the NIC to randomly go off-line for no apparent reason? [655548.189113] type=1505 audit(1277067560.902:5): operation="profile_load" name="/usr/bin/freshclam&q........
  • Seagate Drive 500GB Drive Dying


    This drive is clearly on the way out, the Kernel knows it but I'm surprised that SMART is not concerned. I didn't blame Seagate for their past issues until now. This hard drive has hardly been used and has not even been powered on for a year according to SMART. Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.11 Device........
  • Seagate 7200.11 firmware defect in 500GB, 1000GB (1TB) and 1500GB (1.5TB) Hard Drives


    Seagate Inventory/Firmware Check I heard about this issue a long time ago but never looked into it. I figured I wasn't affected since my 500GB drives were running for so long. I've been using Seagate's since 2002 and to this day all of the drives I have are alive from Seagate. *Update the bad news is that I realize one of my 500GB's is about to die, it's not even a year old, but is also not affected by the recall according to Seagate! Seagate Inventory/Firm........
  • OCFS2 crash


    When trying to even cd or ls the mounted OCFS2 partition it crashes. Ithink this is a combination of VMWare Server's problem and the way I mounted and symlinked to it. More than anything this shows the problem and lack of forsight with VMWare, but also that OCFS2 is easily crashed if you do strange things. Output of /var/log/messages for OCFS2 Apr 10 15:57:45 localhost kernel: [84331.691258] Modules linked in: vmnet vmci vmmon ocfs2_stac........
  • Latest Articles

  • VMWare Pro Workstation Nic Disconnected and No IP Using NAT
  • Linux How To Create A RamDisk
  • mdadm force resync when resync=PENDING solution
  • Proxmox Breaks Storage/LVM Backing If Killing QEMU-IMG
  • Proxmox trying to acquire lock... TASK ERROR: can't lock file '/var/lock/qemu-server/lock-102.conf' - got timeout
  • Debian 9 SSH root password authentication failure password not working problem / solution
  • QEMU / KVM How To Manually Create Basic Virtual Machine VM
  • Linux wlan0 check all wireless clients
  • PHP Issues With Decoding Strange Smart Quotes And Non-Standard ASCII Characters
  • /etc/iproute2/rt_tables default settings file in Linux Centos 6,7 and most other NIX's
  • bind named error solutions named[2169]: error (no valid DS) resolving / error (broken trust chain) resolving / : error (no valid RRSIG) resolving 'com/DS/IN':
  • iptables how to log ALL dropped incoming packets
  • How To Edit Linux Based NM Network Manager Connection Settings Without GUI
  • Linux Disable IPV6 Centos / Debian / Mint Howto
  • Linux use growisofs to burn a larger file on a BD-R / Bluray Disc
  • Linux partprobe/partx cannot access last and 4th partition
  • DRBD Errors Caused By Physical Corruption
  • mdadm: add new device failed for /dev/sdb4 as 3: Invalid argument solution
  • Linux named / bind how to dump, view and clear the cache!
  • Centos 6 / 7 / 8 How To Change Default nameservers in /etc/resolv.conf when using DHCP / dhclient