Usually when I come across a system like this, Ijust flash the firmware to an IT mode so we get just an AHCI system with JBOD, but sometimes it is not practical for remote systems or if we fear that flashing is too risky if something goes wrong. In this case, we unfortunately have to use LSI/Broadcom proprietary CLI tools (megacli) to even make the drives visible. Step 1 - Download MegaCLI The official broadcom packages lack .deb packages and only have .rpm for........

It really seems limited in that it can mainly give you the things you would see on the physical unit such as load etc.. wget https://downloads.sourceforge.net/project/apcupsd/apcupsd%20-%20Stable/3.14.14/apcupsd-3.14.14.tar.gz?r=https%3A%2F%2Fsourceforge.net%2Fprojects%2Fapcupsd%2Ffiles%2Flatest%2Fdownload&ts=1598115866 tar -zxvf apcupsd-3.14.14.tar.gz cd apcupsd-3.14.14 [root@somebox apcupsd-3.14.14]# ./conf........

#if you have nvidia make sure you install the nvidia-cuda-toolkit so hardware acceleration can be used wget http://ffmpeg.org/releases/ffmpeg-3.3.2.tar.bz2 tar -jxvf ffmpeg-3.3.2.tar.bz2 cd ffmpeg-3.3.2/ ./configure --disable-yasm install prefix /usr/local source path ........

When running cudaminer once it tries to initialize the card the entire screen freezes. The computer itself is still running but the Xorg is done for, you cannot even switch to another console window and must reboot (even an mdm or Xorg restart does not help). At first cudaminer will give you these errors: stratrum_recv_line failed ...retry after 15 seconds GPU #0: Geforce 210 with compute ca........

[2017/06/12 21:14:04.991169, 0] ../source3/param/loadparm.c:3259(process_usershare_file) process_usershare_file: stat of /var/lib/samba/usershares/dump failed. Permission denied Issue was the parent directory needed chmod 755........

The solution was to reinstall the vbox dkms package and do a manual modprobe of the modules it makes. I never sorted out the unable to start due to the USB issue, I did have the guest additions installed but the only way to boot was to change the pointing device from USB to PS2 and then to disable the USB controller (if your pointing device is set as USB, disabling USB will not work because it will re-enable by default when it sees your pointing device is USB, this is w........

One thing to remember is that you need MegaCli to do the flashing. You also need the correct file,I tried at least 2 different Perc 6 firmwares from Dell that kept getting rejected as corrupt by MegaCli(they were really the wrong version). I have an external PCI-E Dell 6 Perc/I butI chose images from the 'Integrated" on motherboard version as it was allI could find. They are different, and below is my first time finding success.........

I flashed an LSI Logic firmware to it and it broke the BIOS (cannot do Ctrl+R) for booting purposes but allows other functionality to work normally. I tried downgrading to a Dell firmware for Perc 6i but it won't work, not even with MegaCli wget http://downloads.dell.com/FOLDER00416606M/1/SAS-RAID_Firmware_W83M2_LN32_6.3.1-0003_A14.BIN --2013-08-26 12:53:39-- http://downloads.dell.com/FOLDER00416606M/1/SAS-RAID_Firmware_W83M2_LN32_6.3.1-0003_A14.BIN Resolvi........

LSi Megaraid At first it was configured as a RAID 0, then I deleted the Virtual Disk Group. I thought both drives would be shown and detected in Linux as sda and sdb but it actually shows nothing. To make them work you have to hit Ctrl+R before the system boots (when prompted) and create a Virtual Disk Group. In my case I created each one as RAID 0 (with a single drive only) as I just wanted JBOD but there is no such option or default in these Dell Pe........

[2013/02/22 19:06:37.373564, 0] param/loadparm.c:8004(lp_do_parameter) Global parameter guest account found in service section! This is annoying but the solution is simple: The line "guest account = " is in the section for a share (in /etc/samba/smb.conf), but it should be under globals. Move it under [global] and then everything should be fine.........

I'll start by showing some problems in the logs: [2011/08/07 16:22:06, 0] param/loadparm.c:8569(process_usershare_file) process_usershare_file: stat of /var/lib/samba/usershares/movie failed. Permission denied [2011/08/07 16:22:06, 1] smbd/service.c:676(make_connection_snum) create_connection_server_info failed: NT_STATUS_ACCESS_DENIED That means you don't have permission to access the fi........

When trying to even cd or ls the mounted OCFS2 partition it crashes. Ithink this is a combination of VMWare Server's problem and the way I mounted and symlinked to it. More than anything this shows the problem and lack of forsight with VMWare, but also that OCFS2 is easily crashed if you do strange things. Output of /var/log/messages for OCFS2 Apr 10 15:57:45 localhost kernel: [84331.691258] Modules linked in: vmnet vmci vmmon ocfs2_stac........