systemd is like the service manager for your Centos and other modern Linux distributions (including Debian/Mint/Ubuntu) allows you to enable services, stop them, restart them, check their status and even reboot your system.
The key commands or arguments you will use with systemctl are the following:
list-units [PATTERN...] List loaded units
edit theme css:
Click "Appearance -> Editor -> Stylesheet"
/*font-family: Merriweather, Georgia, serif;*/
font-family: "Lucida Sans Unicode", "Lucida Grande", sans-serif........
**** Warning: can't process font stream, loading font by the name.
Can't find CMap Identity-UTF16-H building a CIDDecoding resource.
Warning: falling back to Identity ordering
**** Error reading a content stream. The page may be incomplete.
**** File did not complete the page properly and may be damaged.
**** This file had errors that were repaired or ignored.
170110 5:35:23 [Note] /usr/libexec/mysqld: Normal shutdown
170110 5:35:23 [Note] Event Scheduler: Purging the queue. 0 events
170110 5:35:23 InnoDB: Starting shutdown...
170110 5:35:24 InnoDB: Shutdown completed; log sequence number 0 12765401
170110 5:35:24 [Note] /usr/libexec/mysqld: Shutdown complete
170110 05:35:24 mysqld_safe mysqld from pid file /var/run/mysqld/mysqld.pid ended........
It is a permissions issue that is hard to fix.
All but one USB device is greyed out.
I am already a member of "vboxusers"
I have already enabled and disabled USB support for the guest.
I have already reinstalled the latest VBOx guest editions
If running as root it all works fine
You need to use the Samsung driver but specify it as a CLP-360 (this is what I used for my CLP365) and incidentally most of these units look identical on the outside on inside (I've been buying whatever the latest C300 and now 400 unit for years which all seem the same with slightly different features that I never use).
Once again try specifying earlier models and revisions if the printer doesn't print (it will say it's been sent to the printer bu........
At first it was configured as a RAID 0, then I deleted the Virtual Disk Group.
I thought both drives would be shown and detected in Linux as sda and sdb but it actually shows nothing.
To make them work you have to hit Ctrl+R before the system boots (when prompted) and create a Virtual Disk Group. In my case I created each one as RAID 0 (with a single drive only) as I just wanted JBOD but there is no such option or default in these Dell Pe........
pxe-32 tftp open timeout
The solution was to enable tftp in xinetd with "chkconfig tftp on".
See the troubleshooting below:
NetworkManager 0:off 1:off 2:off 3:off 4:off 5:off 6:off
I dread updating the kernel and rebooting to find the Ubuntu graphics aren't working and you have to manually intervene. This is usually because Ubuntu for whatever reason didn't update the drivers you need (eg. the manually compiled Nvidia Kernel driver that MUST be recompiled for each and every kernel update unfortunately).
The most common reason may be that "linux-source" hasn't been installed automatically on my system. I tried to manually reinstall the........
I'm posting this because it wasn't easy or obvious how this would be accomplished and the man page leaves it to guesswork.
I've only used it on Centos, soI thought I'd make a quick Debian guide:
Install the DRBD Package
apt-get install drbd8-utils
Reading package lists... Done
Building dependency tree
Reading state information... Done
The following packages were automatically installed and are no longer required:
Use 'apt-get autoremove' to remove them.
After an upgrade wine wouldn't open anything, not even the pre-installed notepad.
There are no wine logs and nothing is mentioned in any standard log file about why.
I finally decided to run wine from the shell and see what's going on:
wine client error:0: version mismatch 398/402.
Your wineserver binary was not upgraded correctly,
or you have an older one somewhere in your PATH.
Or maybe the wrong wineserver is still running?........
This was unbelievable how much the Xen kernel slows things down, keep in mind both tests were done on the hostnode, one was with the Openvz-Xen hybrid kernel and the other was just OpenVZ. You can see the performance difference is nearly 300% better when not using the Xen kernel.
OpenVZ-Xen Kernel Test Results (I was wondering what was wrong/so slow with my Core i5!)
# # # # # #&n........
Seagate Inventory/Firmware Check
I heard about this issue a long time ago but never looked into it. I figured I wasn't affected since my 500GB drives were running for so long. I've been using Seagate's since 2002 and to this day all of the drives I have are alive from Seagate.
*Update the bad news is that I realize one of my 500GB's is about to die, it's not even a year old, but is also not affected by the recall according to Seagate!
Proxmox has made this free utility to backup running OpenVZ containers. It's a great program which is actually just a PERL script but gets the job done. This program is not 100% required because all it really does is cp -a from your container's path as far as I know but it is still good to have uniformity to how you backup your containers.
For RPM distros such as Centos/RHEL/Fedora etc.. download and install this: