• Centos 7 A start job is running for dev-mapper-clx2droot.device (8min 44s / no limit)


    This error is usually because of some sort of encryption in this case a Seagate enclosure with encryption (even though not enabled) did not allow this hard drive to boot.........
  • USB 3.0 External HDD Enclosure Seagate UAS problems - [sdd] tag#1 CDB: Write(16) 8a 00 00 00 00 01 70 04 08 68 00 00 00 08 00 00


    This is a 8TB Seagate external USB 3.0 device apparently newer kernels use a module called "UAS" instead of "USB Storage" which causes issues as a lot of devices are not properly supported in UAS mode by the kernel driver. The solution some say is to disable UAS specifically for your USB device but I'd rather just disable UAS altogether. Solution blacklist UAS: *do not do this it does not work and just causes your USB 3.0........
  • USB 3.0 PCI x1 Card Review VIA VL805 on Linux Review and Experience


    This is a VIA made VL805 USB 3.0 Chipset with 4-ports and MOLEX powered. First of all this unit was cheap at about only 9 USD with fast shipping. My biggest concern was if this was a quality unit and would it really give you full USB 3.0 speeds (some people reported with similar cards that for some weird r........
  • ADATA SU800 256GB 3D NAND Flash SSD Test & Review


    I keep reading these drives are slower, but they are cheap and still SSDand work very fast for my needs. As you can see the sequential read is 481-491MB/s, if I put them in MDADM RAID10 mode (normal RAID1) they should give me well over 900MB/s and with redundancy and being very cheap for what they offer. [1232206.315622] scsi 8:0:1:0: Direct-Access ATA ADATA SU800&........
  • Dell Perc 6/i SATA benchmarks without battery


    The results are not bad, the Hitachi performs the same as it does in a SATA2 motherboard. However, the 2TB is much different, on a similar 2TB Toshiba I get about 198MB/s on a different motherboard vs the 2TB Hitachi which should produce similar results. This Dell Perc 6/i is on a PCI x8 riser card and is connected to a 12-port backplane. Adapter #0 Enclosure Device ID: 32 Slot Number: 0 Enclosure position: N/A De........
  • LSI MegaRAID Adventures, Guide and HowTo


    LSi Megaraid At first it was configured as a RAID 0, then I deleted the Virtual Disk Group. I thought both drives would be shown and detected in Linux as sda and sdb but it actually shows nothing. To make them work you have to hit Ctrl+R before the system boots (when prompted) and create a Virtual Disk Group. In my case I created each one as RAID 0 (with a single drive only) as I just wanted JBOD but there is no such option or default in these Dell Pe........
  • Dying Samsung DVDRW Drive


    My Samsung drive failed on me, at first I thought it was the enclosure but a direct SATA connection causes the same problems for discs that are inserted. It will work fine for a few minutes but then starts spewing the errors below. I've never been a fan of Korean made optical drives and have always had trouble with them. The problem is that I don't believe NEC and Lite-ON make drives anymore, and I considered them the leaders. Apr 7 11:58:48 bo........
  • Wireless/xmit power - DD-WRT v23 SP2 (09/15/06) std - build 3932 Linksys WRT54G/GL/GS


    I played around with xmit power (how much power in mW) to see if I could increase the range and signal strength. Idon't think this Linksys WRT54G's strength is the wireless, it seems to have poor signal quality and transfer rates all around. Ithink part of the problem is also that there are several wireless networks around my house that could be interfering and the walls are thick here. Anyaway, moving on now :) The default is 28mW and I increased it to........
  • Latest Articles

  • virt-resize: error: libguestfs error: could not create appliance through libvirt.
  • Asterisk Does Not Retry When Authentication Fails
  • Linux Debian Ubuntu How To Install PEPPER Faster and Latest Adobe Flash Player in Firefox
  • How To Speed Up Linux Ubuntu and Debian Based Computers By Improving CPU Performance and Changing the CPU Governor
  • Convert data or file to base64 on a single line
  • Linux Mint Ubuntu Debian radeon slow 2D performance issues radeon_dp_aux_transfer_native: 158 callbacks suppressed
  • mdadm: super0.90 cannot open /dev/sdb1: Device or resource busy mdadm: /dev/sdb1 is not suitable for this array.
  • How To Install NextCloud on Centos 7 and Centos 8
  • AH01630: client denied by server configuration:
  • ERROR: Could not find a version that satisfies the requirement PIL (from versions: none) ERROR: No matching distribution found for PIL
  • ZTE Camera Cannot Work unable to connect to camera. Camera has been disabled becaue of security policies or is being used by other apps
  • QEMU KVM how to boot off a physical CD/DVD/BDROM Drive
  • How To Install OpenProject on Centos 7 Step-by-Step Guide
  • Ubuntu Debian Linux Cannot Install Wine Solution - wine1.6 : Depends: wine1.6-i386 (= 1:1.6.2-0ubuntu14.2) but it is not installable wine1.4 : Depends: wine1.6 but it is not going to be installed
  • How To Install python 3.4 3.5 and up on Linux with wine - Working Solution
  • using Xvfb on virtual remote ssh server to have X graphical programs work
  • ssh Received disconnect from port 22:2: Too many authentication failures
  • named bind errors - DNSKEY: unable to find a DNSKEY which verifies the DNSKEY RRset and also matches a trusted key for '.'
  • OpenVZ vs LXC DIR mode poor security in LXC
  • httpd: Syntax error on line 221 of /etc/httpd/conf/httpd.conf: Syntax error on line 6 of /etc/httpd/conf.d/php.conf: Cannot load modules/libphp5.so into server: /lib64/libresolv.so.2: symbol __h_errno, version GLIBC_PRIVATE not defined in file libc.s