Assign way more replicas than you have of memory on all nodes and watch the Swarm crash which can easily reproduce in a small VMfor testing. root@Deb11Docker01:~# docker ps CONTAINER ID IMAGE COMMAND CREATED STATUS PORTS NAM........

This seems to happen in many different drivers but it happened more often in newer versions such as 530 vs 525. Then nvidia-modeset goes to 100% There are many reports of this appearing since driver 4.70 and I can confirm I've seen this in various machines. https://forums.de........

Proxmox's documentation shows the following here. Which mainly just says change /etc/hosts and /etc/hostname with your new hostname. Here's what happens if you only do that: If you just do the above, you will find you have an inaccessible original hostname that contains those VMs and you cannot........

If you are installing ta-lib for Python and get this error then you can normally solve it by manually getting the ta-lib source files and compiling. tar -zxvf ta-lib-0.4.0-src.tar.gz cd ta-lib;./configure;make;make install Collecting ta-lib Downloading https://files.pythonhosted.org/packages/39/6f/6acaee2eac6afb2cc6a2adcb294080577f9983fbd2726395b9047c4e13ec/TA-Lib-0.4.26.tar.gz (272kB) &nbs........

Virtualbox is a very powerful tool, but for some use cases it is less than optimal. Say you are in a work, lab or other environment where you are not alone on the physical network and there could be overlap of IPs, but you need all of your VMs to be contactable from your host, VMs need to communicate with each other, and VMs need internet. NAT Network will give you VM to VM communication and internet, however, it is buggy and unstable. It also doesn't allow host to VM co........

If you find your NAT Network is not working properly, the first thing you may want to do is list the networks, check their status and make sure the Network is actually started and configured as you expect (eg. is DHCP on and enabled?). This is a long known, unresolved bug that seems to affect Version 6 randomly and disportionately on especially Mint 20/Ubuntu 18. https://www.virtualbox.org/ticket/1474........

Bonding is an excellent way to get both increased redundancy and throughput. It is similar to the "Network Teaming" feature in Windows. There are a few different modes but we will use mode 6, I think it's the best of both worlds, as it is not just a failover, but it provides round robin, so you will get redundancy and load balancing. So if you have a 1G single port, you will have a combined throughput of 4G at this point. Just bear in mind that the true thr........

The Best Docker Tutorial for Beginners We quickly explain the basic Docker concepts and show you how to do the most common tasks from starting your first container, to making custom images, a Docker Swarm Cluster Tutorial, docker compose and Docker buildfiles.........

Why choose OpenVPN instead of a firewall appliance? OpenVPN can be a reliable and easy replacement for traditional hardware or just be an additional tool that your company uses so that the firewall can focus on its job rather than acting as a VPNappliance at the same time. When comparing OpenVPN with traditional firewal........

This normally happens when you interrupt the install of Ceph: pveceph install update available package list start installation Reading package lists... Done Building dependency tree... Done Reading state information... Done gdisk is already the newest version (1.0.6-1.1). ceph-common is already the newest version (15.2.15-pve1). ceph-fuse is already the newest version (15.2.15-pve1). Some package........

Are you getting this error in Proxmox while trying to apt update or install Ceph? apt update Hit:1 http://security.debian.org bullseye-security InRelease Err:2 https://enterprise.proxmox.com/debian/pve bullseye InRelease 401 Unauthorized [IP: 144.217.225.162 443] Hit:3 http://ftp.hk.debian.org/debian bullseye InRelease ........

There are many reasons why Proxmox services may not start, but one common one, is if you have changed your /etc/hostname or /etc/hosts and don't have a valid FQDN (eg. proxmox01 instead proxmox01.com). Failed to start The Proxmox VE cluster filesystem. Failed to start Proxmox VE firewall. Failed to start PVE Status Daemon. Failed to start Proxmox VE scheduler. Failed to start PVE Cluster HA Resource Manager Daemon. Failed to star........

The easiest way to know if your videos are playing with GPU acceleration are to watch the process of xplayer, mpv or whatever you are playing. The CPU usage should be no more than 10% for that process/program if it is using acceleration. Let's manually play with vdpau to make sure it works before we make it permanent: First make sure you have libvdpau installed: sudo apt install vdpau-driver-all If yo........

I find that the default settings for the radeon driver that is applied to most AMD cards is horrible. For example by default TearFree is not enabled and it causes videos to have some kind of square artifacts. Here are the settings I have found most suitable for AMD cards: You need to create file in the following path and restart Xorg or your computer to apply it: *Beware that making a mistake here will possibly make your computer........

Just edit your tftp file for xinetd like this: *Change the IPto be the IPof the interface you want to listen on. To test if your tftp is available on a certain IP range use nc -u yourip 69 to see if you can still connect (/var/log/messages or /var/log/syslog) should show the connection if it is open. Oct 13 23:20:34 01 xinetd[26631]: Started working: 1 available servic........

Install Errors on Version 12: This error happened on QEMU emulator version 2.11.1 pve-qemu-kvm_2.11.1-5 on Proxmox/Debian but installing on QEMU.12 on Centos 6 did not produce the error. *Update it is not related to the OS or QEMU version. This happened in Centos 6 too after a second install. What really causes this even though you successfully install........

debug1: Local connections to LOCALHOST:18006 forwarded to remote address 192.168.1.93:8006 debug1: Local forwarding listening on 127.0.0.1 port 18006. debug1: channel 0: new [port listener] debug1: Local forwarding listening on ::1 port 18006. bind: Cannot assign requested address What we are seeing is that we can't listen on an IPV6 address of ::1. We need to tell SSH to stop using IPV6 so we'll edit ssh_config to take care of this issue........

I tried to stop a qemu-img copy or clone and it broke everything. It was fine to "stop" it from the GUI but a process still persisted so I killed the relevant qemu-img and the kernel went crazy. It also may not have helped that I tried to lvremove a different volume (an unused disk). But either way it breaks LVM (you cannot even run lvdisplay) so a reboot is necessary. Jan 17 06:45:21 testserver kernel: [ 5680.439337] systemd-udevd D 0&nbs........

Just find the relevant file in /etc/NetworkManager/system-connections sudo vi /etc/NetworkManager/system-connections/Wired connection 1 [802-3-ethernet] duplex=full mac-address=00:00:00:FE:FE:FE [connection] id=Wired connection 1 type=802-3-ethernet timestamp=1532403341 [ipv6] method=ignore [ipv4] method=manual........

Set this in /etc/sysctl.conf net.ipv6.conf.all.disable_ipv6 = 1 #apply the settings sudo sysctl -p ........

yes it does create its own json ============================================ cat /tmp/vcsaUiInstaller/ovftool-20180809-175238948-20180809-175603497.log |grep -i json 2018-08-09T17:56:04.238-07:00 verbose OVFTool[30966] [Originator@6876 sub=Default] Manifest file entry: SHA1(VMware-vCenter-Server-Appliance-6.7.0.12000-8832884_OVF10-file1.json) = 1deb658c724767697587d5909c4051c01813e6a1 --> ........

#mount the VCSA DVD mount /dev/sr0 /mnt/cd #alternatively you could mount the iso directly mount -o loop vcsa.iso /your/mount/path #for this purpose we are using the CLI installer on Linux cd /mnt/cd/vcsa-cli-installer/lin64 #no it's not going to be that easy you can't just run vcsa-deploy like that you need to use a template or configured .json file ./vcsa-deploy Usage: vcsa-deploy [-h] [--version] [--supported-deploymen........

10/07/2018 03:05:14 PM [IPv4] Got connection from client10.10.25.1 10/07/2018 03:05:14 PM other clients: 10/07/2018 03:05:14 PM Client Protocol Version 3.7 10/07/2018 03:05:14 PM Advertising security type 18 10/07/2018 03:05:14 PM Client returned security type 18 10/07/2018 03:05:14 PM TLS Handshake failed: Could not negotiate a supported cipher suite. 10/07/2018 03:05:14 PM Client10.10.25.1 gone 10/07/2018 03:05:14 PM Statistics:........

Sometimes if you have a very basic configuration OpenVPN on the client side for some reason sends all traffic to the OpenVPN server IP through the tun0 which is of course impossible and creates a block or routing loop. This is because you need to use your normal ISP/LANgateway to hit the OpenVPN server if it is remote/offsite as is usually the case. So if you are connected to the OpenVPN through say a tun0 device and your routing is set to connect to the OpenVPN&nbs........

The Linux Kernel interpretated a very high volume of real traffic as a DDOS attack so it basically ends up blocking your web server. possible SYN flooding on ctid 42131, port 80. Sending cookies. Simple fix edit sysctl values for max_syn_backlog sysctl -w net.ipv4.tcp_max_syn_backlog=5000 To make them permanent edit /etc/sysctl.conf echo "net.ipv4.tcp_........

#if you have nvidia make sure you install the nvidia-cuda-toolkit so hardware acceleration can be used wget http://ffmpeg.org/releases/ffmpeg-3.3.2.tar.bz2 tar -jxvf ffmpeg-3.3.2.tar.bz2 cd ffmpeg-3.3.2/ ./configure --disable-yasm install prefix /usr/local source path ........

In short the solution is just to use vgremove for the actual /dev/mapper device: vgremove /dev/mapper/backups-backuplv box mnt # mdadm --manage /dev/md8 --stop mdadm: Cannot get exclusive access to /dev/md8:Perhaps a running process, mounted filesystem or active volume group? box mnt # lv lvchange lvconvert lvcreate l........

Uh oh [17925926.174277] block drbd0: Handshake successful: Agreed network protocol version 96 [17925926.174325] block drbd0: conn( WFConnection -> WFReportParams ) [17925926.174342] block drbd0: Starting asender thread (from drbd0_receiver [1682]) [17925926.174432] block drbd0: data-integrity-alg: [17925926.174581] block drbd0: drbd_sync_handshake: [17925926.174586] block drbd0: self 2AAE66AF9252D6DB:2815BF........

2017-01-12 14:25:36 529 (ERROR): The installer was unable to verify that your kernel supports IPv6. 2017-01-12 14:25:36 530 (ERROR): The message received when trying to create an IPv6 socket was Address already in use 2017-01-12 14:25:36 531 (ERROR): Please ensure that the ipv6 module is enabled and loaded in your kernel. 2017-01-12 14:25:36 532 (FATAL): Exiting... Solution This happened........

iptables -t nat -A OUTPUT -m addrtype --src-type LOCAL --dst-type LOCAL -p tcp --dport 3306 -j DNAT --to-destination ip.ip.ip.ip iptables -t nat -A POSTROUTING -m addrtype --src-type LOCAL --dst-type UNICAST -j MASQUERADE sysctl -w net.ipv4.conf.all.route_localnet=1 Make sure you substitute "ip.ip.ip.ip" for your real public IP and also the "--dport 3306" for the port you want to forward. Finally run the sysctl command and........

The only solution after trying many suggestions was to simply restart the "vz" service (definitely not preferable). Even doing an ifdown and ifup for venet0 did not help. ifup venet0 Bringing up interface venet0: Configuring interface venet0: net.ipv4.conf.venet0.send_redirects = 0 RTNETLINK answers: Network is down Some errors from log: CPT ERR: d2dc60........

Tired of checking iotop and seeing that your drbd partition is using 99.99% of io all the time and finding your drbd device performs slow in general? This is especially an issue in versions of DRBD in the 8.3 tree in particular one documented case is on "8.3.13" but it likely applies to other devices. The symptoms are that resyncing is fine and normal but any reasonable amount of activity is very slow and lagged and creates a high server load and con........

kernel: [10186978.064405] TCP: time wait bucket table overflow (CT3) Varying opinions are out there but in general it seems like the most common culprit is a lack of privvmpages, with a modern OpenVZ system the best way is to set privvmpages as equal to what your RAM is and this has resolved the messages on another system. If it's truly a TCP issue you can adjust the following parameters:........

I never did get it working, it is too bad as obfsproxy should really be an option and integrated into the OpenVPN client and server or something similar: yum -y install python-pip python-devel No package python-pip available. #install the EPEL repo python-pip install obfsproxy python-pip install obfsproxy -bash: python-pip: command not found pip install obfsproxy &........

yum -y install wget wget -P /etc/yum.repos.d/ http://ftp.openvz.org/openvz.repo rpm --import http://ftp.openvz.org/RPM-GPG-Key-OpenVZ yum -y install vzkernel vzctl #enable ip_forward sed -i s/'net.ipv4.ip_forward = 0'/'net.ipv4.ip_forward = 1'/g /etc/sysctl.conf #all interfaces should not send redirects echo "net.ipv4.conf.default.send_redirects = 1" >> /etc/sysctl.conf echo "net.ipv4.co........

[ 17.208336] tg3 0000:08:00.0: eth0: Link is up at 1000 Mbps, full duplex [ 17.210194] tg3 0000:08:00.0: eth0: Flow control is on for TX and on for RX [ 76.000065] phy0 -> rt2x00lib_request_firmware: Error - Failed to request Firmware. [ 76.002332] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 86.736004] eth0: no IPv6 routers present [ 148.960038] phy0 -> rt2x00lib_request_fi........

What matters most about VPNproviders in 2024? We are highly suspicious of VERYLARGE VPN providers that have LOW PRICES and HUGE DISCOUNTS. The suspicion is that for those who know what costs are involved to purchase thousands of IPs and servers are not small. At the prices that many of the big mainstream providers offer, it is likely unprofitable or barely profitable. Then, how are those companies making money or is that even the goal? There use........

# first we need a physical volume which we use the pvcreate tool to create # I create mine on /dev/sdb3 pvcreate /dev/sdb3 dev_is_mpath: failed to get device for 8:19 Physical volume "/dev/sdb3" successfully created # pvdisplay shows the newly created volume pvdisplay "/dev/sdb3" is a new physical volume of "1.35 TiB" --- NEW Physical volume --- PV N........

Iread this article and still don't understand the issue. If I understand correctly the client negotiates after the first SSLconnection and then gets the correct hostname and thus correct certificate. http://wiki.apache.org/httpd/NameBasedSSLVHostsWithSNI To their credit I know I'm not using SNIbecuase Iget this message in the Apache log :) [warn] Init: You should not use name-based virtual hosts in conjunction with SSL!! B........

vgchange -ay 3 logical volume(s) in volume group "vg_12" now active lvscan inactive '/dev/vg_12/lv_root' [144.04 GB] inherit inactive '/dev/vg_12/lv_home' [1.00 GB] inherit inactive '/dev/vg_12/lv_swap' [7.85 GB] inherit........

This booting error is because the Xen PV guest image uses the Xen kernel, this is not compatible with anything but a host running a Xen kernel. I did a kpartx -av virtual.img and then it created some partitions that showed up in fdisk. I mounted it and did a chroot into it and removed the xen kernel and installed a normal kernel but Xen still shows the same kernel in Grub (only the Xen one). This is strange but it seems like this Xen PV guest has some sort of hidden or........

ip_conntrack: table full, dropping packet. A lot of clients I've seen have this issue, it really seems the default level is way too small. Once this connection tracking table becomes full then packets get dropped which is obviously a bad thing. One thing to be mindful of though is that 350 bytes of memory are used per entry so there is some justification for not keeping it too high. However, if you have multiple servers running or high traffic daemons........

The normal solution would be as follows: export DISPLAY=:0.0 /usr/lib/vino/vino-server & But what happens if that doesn't work? I haven't been able to find much documentation about how to find the list of displays and how their numbering works in Xorg. Sometimes you'll get this error when trying to restart vino: Cannot open display: For some reason my display is not on 0.0........

netstat is weak and can't show udp connections and most other protocols, use "ss" which is what netstat should have been: The "-u" switch stands for udp, here's a list of other options: Usage: ss [ OPTIONS ] ss [ OPTIONS ] [ FILTER ] -h, --help this message -V, --version output ver........

ping test.com connect: No buffer space available /var/log/messages Oct 18 12:21:03 vps kernel: printk: 177 messages suppressed. Oct 18 12:21:03 vps kernel: Neighbour table overflow. Solution in /etc/sysctl.conf: net.ipv4.neigh.default.gc_thresh1 = 4096 net.ipv4.neigh.default.gc_thresh2 = 8192 net.ipv4.neigh.default.gc_thresh3 = 8192 net.ipv4.neigh.default.base_reachab........

service vz start Starting OpenVZ: failed to load module vzmon [FAILED] vzmon: Unknown symbol ve_snmp_proc_init vzmon: Unknown symbol addrconf_sysctl_free vzmon: Unknown symbol ve_ndisc_init vzmon: Unknown symbol addrconf_ifdown vzmon: Unknown symbol ip6_frag_cleanup vzmon: Unknown symbol fini_ve_route6........

service vz start Starting OpenVZ: failed to load module vzmon [FAILED] vzmon: Unknown symbol ve_snmp_proc_init vzmon: Unknown symbol addrconf_sysctl_free vzmon: Unknown symbol ve_ndisc_init vzmon: Unknown symbol addrconf_ifdown vzmon: Unknown symbol ip6_frag_cleanup vzmon: Unknown symbol fini_ve_route6 ........

cd /etc/yum.repos.d wget http://download.openvz.org/openvz.repo rpm --import http://download.openvz.org/RPM-GPG-Key-OpenVZ yum install ovz-kernel-PAE Now remember to set /etc/sysctl.conf to "net.ipv4.ip_forward = 1" You can apply the change immediately by running sysctl -w net.ipv4.ip_forward = 1 but remember that you still have to set sysctl.conf sysctl -p will load and apply any changes to s........

This is obviously a bug in the r8169 kernel module and it seems to affect a lot of people. I upgraded to the latest kernel and hope this won't happen anymore, as it is a very serious error. This is especially serious for those who are running servers with this chipset, who can afford for the NIC to randomly go off-line for no apparent reason? [655548.189113] type=1505 audit(1277067560.902:5): operation="profile_load" name="/usr/bin/freshclam&q........

This is a great way to use your ftp server space, for example on your web hosting account (althoughI believe many hosts don't allow storage like this), but if you have a VPS/Dedicated Server etc.., this would be perfect. Imagine how easy it is to work with an ftp account that you can just mount as a normal partition or directory in Linux, it would be great for backups etc.. Name curlftpfs - mount a ftp host as a local directory Synopsis........

Proxmox has made this free utility to backup running OpenVZ containers. It's a great program which is actually just a PERL script but gets the job done. This program is not 100% required because all it really does is cp -a from your container's path as far as I know but it is still good to have uniformity to how you backup your containers. For RPM distros such as Centos/RHEL/Fedora etc.. download and install this: wget http://www.proxmox.com/cms_proxm........

PHP cannot access /usr/bin/opensslI have verified the username that runs the process is able to access /usr/bin/openssl and it does exist but the PHP script is saying it doesn't exist: [code:1:1fd0f3abbe] if (!file_exists($OPENSSL)) { //echo "ERROR: OPENSSL $OPENSSL not foundn"; }[/code:1:1fd0f3abbe] I don't get itI can clearly see the contents of /usr/bin by using the PHP system fu........

When trying to even cd or ls the mounted OCFS2 partition it crashes. Ithink this is a combination of VMWare Server's problem and the way I mounted and symlinked to it. More than anything this shows the problem and lack of forsight with VMWare, but also that OCFS2 is easily crashed if you do strange things. Output of /var/log/messages for OCFS2 Apr 10 15:57:45 localhost kernel: [84331.691258] Modules linked in: vmnet vmci vmmon ocfs2_stac........