This would be crucial especially if the phone is hardened, not being able to reset or change settings could prevent a phone registering in a new environment or even when migrating from office to office.
Here is Cisco's guide (timing is everything and it is more tricky than trying to jail break your iPhone):
Step 1 -- While powering up the phone, press and hold #.
Step 2 -- When the light on the mute button and h........
Your database uses Antelope as the file format. Full UTF-8 support in MySQL and MariaDB requires the Barracuda file format. Please switch to the Barracuda file format. See the documentation MySQL full unicode support for details.
In /etc/my.cnf under [mysqld]
180827 21:43:14 InnoDB: 5.5.59 started; log sequence number 1589339
180827 21:43:14 [ERROR] /usr/libexec/mysqld: unknown variable 'db_file_format=Ba........
Sometimes if you have a very basic configuration OpenVPN on the client side for some reason sends all traffic to the OpenVPN server IP through the tun0 which is of course impossible and creates a block or routing loop.
This is because you need to use your normal ISP/LANgateway to hit the OpenVPN server if it is remote/offsite as is usually the case. So if you are connected to the OpenVPN through say a tun0 device and your routing is set to connect to the OpenVPN&nbs........
Here is the only solution Ifound that works in Firefox:
*Note you could basically just copy all of the commands in bold (the rest just shows the output)
sqlite> .clone places.sqlite-fixed
In short the solution is just to use vgremove for the actual /dev/mapper device:
box mnt # mdadm --manage /dev/md8 --stop
mdadm: Cannot get exclusive access to /dev/md8:Perhaps a running process, mounted filesystem or active volume group?
box mnt # lv
lvchange lvconvert lvcreate l........
The solution is simple but strange, if you copy your /var/lib/mysql directory to another server and think it will work, be sure to check if you have /var/log/mysql and binary log files. If you do, the server will not work and will give you errors like below and crash without the proper log files.
UPDATE user SET password=password("newpass") WHERE user='root';
ERROR 2013 (HY000): Lost connection to MySQL server durin........
170110 5:35:23 [Note] /usr/libexec/mysqld: Normal shutdown
170110 5:35:23 [Note] Event Scheduler: Purging the queue. 0 events
170110 5:35:23 InnoDB: Starting shutdown...
170110 5:35:24 InnoDB: Shutdown completed; log sequence number 0 12765401
170110 5:35:24 [Note] /usr/libexec/mysqld: Shutdown complete
170110 05:35:24 mysqld_safe mysqld from pid file /var/run/mysqld/mysqld.pid ended........
# first we need a physical volume which we use the pvcreate tool to create
# I create mine on /dev/sdb3
dev_is_mpath: failed to get device for 8:19
Physical volume "/dev/sdb3" successfully created
# pvdisplay shows the newly created volume
"/dev/sdb3" is a new physical volume of "1.35 TiB"
--- NEW Physical volume ---
service mysqld start
MySQL Daemon failed to start.
Starting mysqld: [FAILED]
130917 17:57:09 InnoDB: Started; log sequence number 0 0
The results are not bad, the Hitachi performs the same as it does in a SATA2 motherboard. However, the 2TB is much different, on a similar 2TB Toshiba I get about 198MB/s on a different motherboard vs the 2TB Hitachi which should produce similar results.
This Dell Perc 6/i is on a PCI x8 riser card and is connected to a 12-port backplane.
Enclosure Device ID: 32
Slot Number: 0
Enclosure position: N/A
At first it was configured as a RAID 0, then I deleted the Virtual Disk Group.
I thought both drives would be shown and detected in Linux as sda and sdb but it actually shows nothing.
To make them work you have to hit Ctrl+R before the system boots (when prompted) and create a Virtual Disk Group. In my case I created each one as RAID 0 (with a single drive only) as I just wanted JBOD but there is no such option or default in these Dell Pe........
don't delete /var/lib/mysql/ib_logfile0 or ibdata1 or mysql won't restart
I didn't realize they were internal and not part of replication like the relay files!
/usr/libexec/mysqld: ready for connections.
Version: '4.1.22-log' socket: '/var/lib/mysql/mysql.sock' port: 3306 Source distribution
110127 16:31:00 [Note] /usr/libexec/mysqld: Normal shutdown
110127 16:31:00 InnoDB: Starting shutdown...........
This server was experiencing loads of up to 80 and maxing out the RAM and kmemsize on a CPanel VPS. There were literally dozens if not hundreds of exim processes. I have no idea why exim has such a design that would allow it to consume this much CPU and RAM. Any normal MTA should not be spawning so many processes, it should be processing them in sequence and if it is going to spawn hundreds of processes in response to a large volume of mail, it's better to have a delayed del........
I'm really starting to love ImageMagick, I've used it to mass convert/resize family photos with scripts and all kinds of handy things.
Today I just learned that you can create PDF files with it too, say if you have images scanned or anything else it's very simple:
convert *.jpeg output.pdf
You can replace jpg with whatever format your files are in. One thing to remember is that you can specify the order that the images/pages are added to the PDF manu........