This is certainly a poor design, as you can read many seasoned admins who have updated their iDRAC only to have it killed. One possible cause is not by doing all the incremental updates, doing updates from an old iDRAC to one many revisions newer is a sure way to kill things, but even then there is no guarantee based on the amount of failures. List of threads of people's dead iDRAC's:........

First we need a few extra packages: apt update apt install -y adduser libfontconfig1 musl sudo wget https://dl.grafana.com/enterprise/release/grafana-enterprise_10.3.1_amd64.deb Install / Enable Grafana dpkg -i grafana-enterprise_10.3.1_amd64.deb dpkg -i grafana-enterprise_10.3.1_amd64.deb (Reading database ... 44309 files and directories currently installed.) Preparin........

You'll notice that /etc/resolv.conf contains dire warners on most Linux Desktops. # This file is managed by man:systemd-resolved(8). Do not edit. # # This is a dynamic resolv.conf file for connecting local clients to the # internal DNS stub resolver of systemd-resolved. This file lists all # configured search domains. # # Run "resolvectl status" to see details about the uplink DNS servers # currently in use........

By default if you create a private key for SSH, it will create something like .ssh/id_rsa Linux will always search for and offer this key when connecting to servers. If you put extra keys in your .ssh directory like id_rsa_realtechtalk.com, they will be ignored by default and NOT used or offered (you can verify this with ssh -v) and see it is not being offered. Here is how you add the extra SSH keys so they are all offered: #this gives........

If you get this error when trying to SSHto a device or machine and you never even got a password prompt: Too many authentication failures This means that either the remote side is configured for key auth only, OR your client side may be attempting to auth using mulitple keys, and that exceeds the amount of attempted authorizations on the remote ssh server. If the issue is trying to auth too many times which ssh defaults to sending the keys to, you ca........

I was using a small box as a router and one of the ports started going off and coming back at 100M. I truly believe it is simply that it was a case of overheating. Although CPUtemps were only about 67 degrees, the physical box itself was almost burning hot. Isolved the cooling issue and never had the issue again. Jul 28 15:09:27 swithbox kernel: e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx Jul 28 15:09:28 swithbox kernel:........

apt install software-properties-common add-apt-repository ppa:deadsnakes/ppa apt update apt install python3-pip apt install python3.7 curl gnupg python3.7-dev git ln -s /usr/bin/python3.7 /usr/bin/python3 pip3 install numpy keras_preprocessing curl https://bazel.build/bazel-release.pub.gpg | sudo apt-key add - echo "deb [arch=amd64] http://storage.googleapis.com/bazel-apt stable jdk1.8" | sudo tee /etc/apt/sources.list.d/bazel........

Just run this apt install command sudo apt install pepperflashplugin-nonfree browser-plugin-freshplayer-pepperflash After this restart your browser and check Adobe's site to verify if your Pepper flash is working and showing at least version 32. https://helpx.adobe.com/flash-player.html As you'll see below it will download the latest version which is currently 32 and this was not possible with the old/crappy deprecated adobe-flash plu........

This is sure simple if you follow the guide but it took a lot of hacking around to make this work on Debian/Ubuntu! Now before you ask why bother running wine and python, the reason is because Python executables are NOT cross-platform. If you run pyinstaller in Linux, that binary will only run on Linux and the same if you do it in Windows. So it is preferable if you have a single environment that you can create Linux and Windows binaries from rather than running 2 separate........

If you are getting this error it is usually caused by having more than 5 keys in your ".ssh" directory. It is a bit of a bug and this is how it manifests itself. You will find at this point that you are not given any chance to enter a password, or if you are using key based auth that the same thing happens. You'll also find that this is happening with ALLservers you try connecting to. The solution is to move away key pairs from .ssh so that there ar........

Yes you have that right, the network service in RHEL8 / CentOS 8 / Rocky Linux / Alma Linux no longer exists. So there is no more systemctl restart network You can restart NetworkManager but it doesn't have the same effect or ifup/ifdown on all interfaces. Generally if NetworkManager is installed you will want to restart it or it won't apply the settings from ifcfg. systemctl restart NetworkManager To repl........

It is really simple using .htaccess with mod_rewrite. Here is all you need: RewriteCond %{SERVER_PORT} 80 RewriteRule ^(.*)$ https://site.com/$1 [R=301,L] Another more graceful way is to use the %{SERVER_NAME}variable to make it dynamic. Just be careful that the server name will always match what you expect. (eg. if you are doing load balancing or clustering what if the server name may be somethi........

SSH helps keep us secure in many ways, one of those is the host-key fingerprint which is unique. If you have been connecting to an SSH server that you've made no changes to and suddenly ssh warns that the key doesn't match then you have a problem. But how about connecting to an existing server for the first time on a new machine or client? A lot of new clients calculate it using an SHA256 hash but it is not as easy on your host machine to produce the sam........

Are you tired of coming back to your computer only to find your SSH connections have been broken? Even worse are the ones that hang where it appears to be connected but it is really not. The one option you have is an SSHclient side modification to send KeepAlive packets, sometimes this can also keep up your WiFi connection and stop it from disconnecting you as well. To make the keep alive changes for your just yourself (not system wide)........

This is a common issue that I haven't seen many answers for on the internet. When you are using Linux as your host machine and you are connecting to another Linux machine over VNC you CANNOT use Ctrl+Alt+F1 to change virtual consoles as it sends the keys to your actual local machine. In many versions of Linux you can cycle through virtual terminals including over VNC using this: Alt + Left Arrow or Alt + Right Arrow This........

wget https://downloads.linux.hpe.com/repo/spp/rhel/6/x86_64/current/CP017004.scexe --2018-08-16 05:11:16-- https://downloads.linux.hpe.com/repo/spp/rhel/6/x86_64/current/CP017004.scexe Resolving downloads.linux.hpe.com (downloads.linux.hpe.com)... 15.249.152.85 Connecting to downloads.linux.hpe.com (downloads.linux.hpe.com)|15.249.152.85|:443... connected. HTTP request sent, awaiting response... 200 OK Length: 1525561 (1.5........

Error 0 occurred while receiving the document root@vh1:/var/tmp# wget http://mirror.compevo.com/proxmox/proxmox-ve_5.2-1.iso --2018-08-30 16:27:37-- http://mirror.compevo.com/proxmox/proxmox-ve_5.2-1.iso Resolving mirror.compevo.com (mirror.compevo.com)... 103.25.61.44 Connecting to mirror.compevo.com (mirror.compevo.com)|103.25.61.44|:80... connected. HTTP request sent, awaiting response... 200 OK Length: 641517568 (612M) [application/o........

sudo apt-get install libcurl4-openssl-dev git build-essential autotools-dev autoconf libcurl3 sudo apt-get install libcurl4-gnutls-dev git clone https://github.com/wolf9466/cpuminer-multi sudo apt-get install cmake libpthread-* libmicrohttpd-dev libssl-dev libhwloc-dev git clone https://github.com/fireice-uk/xmr-stak-cpu.git make install cd bin chmod +x xmr-stak-cpu ./xmr-stak -O xmr........

Sometimes if you have a very basic configuration OpenVPN on the client side for some reason sends all traffic to the OpenVPN server IP through the tun0 which is of course impossible and creates a block or routing loop. This is because you need to use your normal ISP/LANgateway to hit the OpenVPN server if it is remote/offsite as is usually the case. So if you are connected to the OpenVPN through say a tun0 device and your routing is set to connect to the OpenVPN&nbs........

It looks like this has something to do with APIC but I am not sure. I have similar CPUs with a different MB and BIOS that work fine on the same type of kernel. A lot of time the issue is because of the C-step setting in the BIOS. The same thing happened on the 2.6 kernel with Centos 6 but this is a homebrew 4.4 kernel soI am not sure why it is happening when even Centos 7 (3.2) kernel works OK. Solution - It comes down to the BIOS set........

curl: (35) Unknown SSL protocol error in connection The main solution is to update curl and nss. If you are having an issue with curl through Apache/PHPyou will need to restart PHPafter. It's important to remember that this error could mean a lot of things but most often it simply means that curl and openssl may be outdated and only allow newer secure ways of connecting to SSL. In general here is how you would fix it in most c........

ssh rtt@192.168.1.199 Unable to negotiate with 192.168.1.99 port 22: no matching host key type found. Their offer: ssh-dss It looks like the DSS option is not considered secure so when connecting from newer Linux systems to an older one you will get the above error. It can be fixed (but you should consider upgrading your SSH daemon): ssh -oHostKeyAlgorithms=+ssh-dss rtt@192.168.1.199........

sudo mount -a Unable to find suitable address. [35758.706993] CIFS VFS: Error connecting to socket. Aborting operation. [35758.707247] CIFS VFS: cifs_mount failed w/return code = -111 [35795.476160] CIFS VFS: Error connecting to socket. Aborting operation. [35795.476346] CIFS VFS: cifs_mount failed w/return code = -111 When the above happens "Unable eto find suitable address" it usually means the smb nam........

Centos 5 is not supported running yum will produce an error like this: YumRepo Error: All mirror URLs are not using ftp, http[s] or file. Eg. Invalid release/ removing mirrorlist with no valid mirrors: /var/cache/yum/base/mirrorlist.txt Error: Cannot find a valid baseurl for repo: base Solution - Update this file CentOS-Base.repo # CentOS-Base.repo........

Error while connecting to MYSQL: (XID 4ea7s9) Access denied for user 'root'@'localhost' (using password: YES) at /usr/local/cpanel/Cpanel/Mysql.pm line 181 Solution This error occurs because the /root/.my.cnf has the wrong/outdated password for MySQL root user. Simply edit /root/.my.cnf with the correct user. This normally happens if you update outside of cPanel.........

This is especially helpful if you run your own servers. If you are presented with an error message or warning that the signature has changed or does not match the IP/domain you are connecting to you always want to verify manually. So your e-mail/web client will show you an SHA-1 fingerprint like this: "Could not verify this certificate because the issuer is unkown" or other reasons such as a mismatch in IP/domain. It will also show you........

Uh oh [17925926.174277] block drbd0: Handshake successful: Agreed network protocol version 96 [17925926.174325] block drbd0: conn( WFConnection -> WFReportParams ) [17925926.174342] block drbd0: Starting asender thread (from drbd0_receiver [1682]) [17925926.174432] block drbd0: data-integrity-alg: [17925926.174581] block drbd0: drbd_sync_handshake: [17925926.174586] block drbd0: self 2AAE66AF9252D6DB:2815BF........

In Firefox I cannot connect to any website, proxy is disabled and outside network access is confirmed, no system or manual proxy was set on this Linux Mint/Ubuntu system. Normally this can be caused by proxy or DNS problems and the weird thing is that traceroute and ping to other IPs worked fine but even connecting to sites by IP was not working. The connection was reset The connection to the server was reset while the page was loading.........

Fortunately the format is EATX so an EATX case will work and the screw layout is standard. You will need to remove the HEX/TORX screws that are connecting the stock HP standoffs (meant to slide into an HP case). XW9400 Motherboard Issues Size: 12" x 13" Proprietary Power Connector Proprietary CPU Power Connector Proprietary Memory Power Connector Fan connectors are 4 pin so you will need some kind of adapter.........

An error occurred during a connection to site.com. SSL received a record that exceeded the maximum permissible length. (Error code: ssl_error_rx_record_too_long) The page you are trying to view cannot be shown because the authenticity of the received data could not be verified. Please contact the website owners to inform them of this problem. When the above happens in our experience it is a misconfiguration of........

What matters most about VPNproviders in 2024? We are highly suspicious of VERYLARGE VPN providers that have LOW PRICES and HUGE DISCOUNTS. The suspicion is that for those who know what costs are involved to purchase thousands of IPs and servers are not small. At the prices that many of the big mainstream providers offer, it is likely unprofitable or barely profitable. Then, how are those companies making money or is that even the goal? There use........

This problem seemed to happen recently but was likely causing issues before where the phone(s) do not ring. Now there are a few reasons why this can happen especially if your adapter has DND mode enabled (disable it). However that wasn't my issue and Ionly figured it out the other day when by fluke if you're on the phone (making a call) then calls will come in. That's when Ifigured out the solution: This likely app........

/scripts/phpextensionmgr install PHPSuHosin Updating md5sum list Fetching http://httpupdate.cpanel.net/cpanelsync/easy/targz.yaml (connected:0).......(request attempt 1/12)...Resolving httpupdate.cpanel.net...(resolve attempt 1/65)... Fetching http://httpupdate.cpanel.net/mirror_addr_list (connected:0).......(request attempt 1/3)......connecting to 74.50.120.123...@74.50.120.123......connected......receiving...100%......request success......Done........

One thing to remember is that you need MegaCli to do the flashing. You also need the correct file,I tried at least 2 different Perc 6 firmwares from Dell that kept getting rejected as corrupt by MegaCli(they were really the wrong version). I have an external PCI-E Dell 6 Perc/I butI chose images from the 'Integrated" on motherboard version as it was allI could find. They are different, and below is my first time finding success.........

I flashed an LSI Logic firmware to it and it broke the BIOS (cannot do Ctrl+R) for booting purposes but allows other functionality to work normally. I tried downgrading to a Dell firmware for Perc 6i but it won't work, not even with MegaCli wget http://downloads.dell.com/FOLDER00416606M/1/SAS-RAID_Firmware_W83M2_LN32_6.3.1-0003_A14.BIN --2013-08-26 12:53:39-- http://downloads.dell.com/FOLDER00416606M/1/SAS-RAID_Firmware_W83M2_LN32_6.3.1-0003_A14.BIN Resolvi........

LSi Megaraid At first it was configured as a RAID 0, then I deleted the Virtual Disk Group. I thought both drives would be shown and detected in Linux as sda and sdb but it actually shows nothing. To make them work you have to hit Ctrl+R before the system boots (when prompted) and create a Virtual Disk Group. In my case I created each one as RAID 0 (with a single drive only) as I just wanted JBOD but there is no such option or default in these Dell Pe........

Client Log OpenSSH_4.3p2, OpenSSL 0.9.8e-fips-rhel5 01 Jul 2008 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug1: Connecting to 192.168.1.253 [192.168.1.253] port 22. debug1: Connection established. debug1: permanently_set_uid: 0/0 debug1: identity file /root/.ssh/identity type -1 debug1: identity file /root/.ssh/id_rsa type 1 debug1: identity file /root/.ssh/id_d........

This pops up when connecting the phone and it doesn't seem to charge. The phone keeps showing a status message every few seconds "Connected as a media device". It's ridiculous why this phone doesn't just default as a simple USB Mass storage device. Here's what I see in /var/log/messages: Jan 30 18:51:27 QuadCoreAM2 kernel: [18038228.144046] usb 1-3: new high speed USB device using ehci_hcd and address 24 Jan 30 18:51:28 QuadCoreAM2 ke........

It's really silly how DA doesn't enable SSL by default but is otherwise a stable, fast and secure control panel. Here's a copy and paste way of enabling SSL for Directadmin in just a few seconds: *setup SSL openssl req -x509 -newkey rsa:1024 -keyout /usr/local/directadmin/conf/cakey.pem -out /usr/local/directadmin/conf/cacert.pem -days 9999 -nodes That creates the public certificate and private key pair in the location Directadmin expects to fi........

You need to enable the httpd daemon with monit to actually view the status and control, it's not only for the web interface since the httpd is theONLY way of controlling monit and viewing the status. monit monitor all will also reinstate disabled services if they've timed out too much. Just restarting the service will do nothing to re-monitor a service that monit has stopped monitoring due to too many failures. *Also note that /etc/monit.conf i........

Webmin Setup Centos 5: wget http://downloads.sourceforge.net/project/webadmin/webmin/1.530/webmin-1.530-1.noarch.rpm?r=http%3A%2F%2Fwww.webmin.com%2Fstandard.html&ts=1294339690&use_mirror=surfnet [1] 24229 [2] 24230 [root@host ~]# --2011-01-06 21:48:20-- http://downloads.sourceforge.net/project/webadmin/webmin/1.530/webmin-1.530-1.noarch.rpm?r=http%3A%2F%2Fwww.webmin.com%2Fstandard.html Resolving downloads.sourceforge.net... 216.34.181.........

The normal solution doesn't help or apply here: ssh -v user@192.168.5.41 OpenSSH_4.3p2 Debian-9etch3, OpenSSL 0.9.8c 05 Sep 2006 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug1: Connecting to 192.168.5.41 [192.168.5.41] port 22. debug1: Connection established. debug1: permanently_set_uid: 0/0 debug1: identity file /root/.ssh/identity type -1 debug1: i........

cd /usr/local/directadmin/scripts/ scripts]# ./awstats.sh --23:49:28-- http://files.directadmin.com/services/all/awstats/awstats-6.9.tar.gz Resolving files.directadmin.com... 72.35.85.222 Connecting to files.directadmin.com|72.35.85.222|:80... connected. HTTP request sent, awaiting response... 200 OK Length: 1125906 (1.1M) [application/x-gzip] Saving to: `/usr/local/directadmin/scripts/packages/awstats-6.9.tar.gz' 100%[=........

This is a great way to use your ftp server space, for example on your web hosting account (althoughI believe many hosts don't allow storage like this), but if you have a VPS/Dedicated Server etc.., this would be perfect. Imagine how easy it is to work with an ftp account that you can just mount as a normal partition or directory in Linux, it would be great for backups etc.. Name curlftpfs - mount a ftp host as a local directory Synopsis........

I took an educated guess because it kept happening at the same spot when loading the XP install. I thought it was the hard drive or motherboard. But it turns out my heavily used but loved NEC 3500 DVD-RW drive was the culprit. After disconnecting it and swapping it for another much beloved Pioneer DVD-RW, everything has gone smoothly. I never ran into this or many issues because I've hardly used this drive since moving it to another Desktop years ago. I actua........

Trouble connecting between Windows XP and Windows 98 SharesOk a few things to check for: * Disable all firewalls * Make sure NetBEUI is enabled on both computers * Make sure the Windows XP computer has the name of the computer logged in user of Windows 98 added as an XP user * Add the XP user to anything you want to share That fixed my problem........

ECS K7S5A Motherboard System Take Up To 2 Minutes To BootHi guys, My motherboard is very strange. Sometimes it will take up to a few minutes to post. I have no idea it suddenly started doing this. I have tried everything and all I can figure is that it is somehow related to the USB ports possibly. Why do I say this? Because if I disconnect my scanner the problem occurs less frequently. I only have a printer hooked up to USB now and by........

Icouldn't understand why on one system it took a few minutes to get the SSHlogin prompt when connecting to other systems. The other systems all had the UseDNS parameter set to no, which almost always resolves the login prompt delay. The reason is Ubuntu and perhaps Debian and other distributions /etc/nsswitch.conf file Edit yours to have the "hosts" line like so (notice that files and dns are the primary resolution choice........

Server not using user level security and no password supplied. tree connect failed: NT_STATUS_WRONG_PASSWORD That happens when trying to use smbclient to connect to a share. The weird thing is that I can authnenticate just fine from Windows XP. It is partially my mistake, I forgot this share does have a password. I've tried authenticating with the correct user and also with "Guest" because this works in Windows. In Linux I ........

This will give you the basic info needed to browse and connect to Samba shares from the command line. From the GUI of Gnome or KDE etc, it is pretty standard and straight forward. However, I've found very little guides on how to do it from the command line and if you're like me, a nerd who prefers command line for its simplicity and for remote use, this is the way to go. First get a list of all the Samba/SMB shares on the target. smbclient -L hostname........