This is certainly a poor design, as you can read many seasoned admins who have updated their iDRAC only to have it killed. One possible cause is not by doing all the incremental updates, doing updates from an old iDRAC to one many revisions newer is a sure way to kill things, but even then there is no guarantee based on the amount of failures. List of threads of people's dead iDRAC's:........

So say you happen to have 2 NICs of the exact same chipset, they will generally show up as the same name, with possibly a different revision in lspci. Normally this is not an issue if you have a server with 4 NICs, generally the eth0 to eth3 appears from left to the right (or right to left on some vendors) so it doesn't take much figuring out. Generally if you have different chipsets for different NICs, it should be easy to know which one is eth0 or the first NIC in the OS.........

This is the reason that I don't like the new ADATA USB drives such as the UV128/64GB or 128GB drives and other ones that look to be the same style (the green sliding USB connector). They just don't work well from new and never work properly at any point. [ 788.242463] usb 1-1.2: new high-speed USB device number 16 using ehci-pci [ 788.339816] usb 1-1.2: New USB device found, idVendor=125f, idProduct=db8a [ 7........

Normally the below would indicate a failing or failed drive. In this case the SATA port was unplugged and sometimes the Linux kernel/motherboard even with AHCIjust don't play nice and can't handle it. What happened is Iplugged in a new drive after removing another one. However the log shows that after the old drive was plugged in the Linux kernel kept complaining thinking the drive was there but not responding properly. This continued even with reseating........

[ 2868.041375] ata1: EH in SWNCQ mode,QC:qc_active 0x40 sactive 0x40 [ 2868.041554] ata1: SWNCQ:qc_active 0x40 defer_bits 0x0 last_issue_tag 0x6 [ 2868.041556] dhfis 0x40 dmafis 0x40 sdbfis 0x20 [ 2868.041874] ata1: ATA_REG 0x41 ERR_REG 0x84 [ 2868.042013] ata1: tag : dhfis dmafis sdbfis sactive [ 2868.042163] ata1: tag 0x6: 1 1 0 1 [ 2868.042301] ata1.00: exception Emask 0x1 SAct 0x40 SErr 0x400000 action 0x6 frozen [........

If you remove the white label on the chip (near the CMOS battery) you will find the following details about it: SST 49LF080A 33-4C-NHE It is the PLCC32 type and can be pried and removed safely (but be very careful) with an eye glass flat head screw driver. If you just have a bad flash you may be able to reprogram your original or just buy another one with the part# above and reprogram it. This is great news for people who have bricked th........

Fortunately the format is EATX so an EATX case will work and the screw layout is standard. You will need to remove the HEX/TORX screws that are connecting the stock HP standoffs (meant to slide into an HP case). XW9400 Motherboard Issues Size: 12" x 13" Proprietary Power Connector Proprietary CPU Power Connector Proprietary Memory Power Connector Fan connectors are 4 pin so you will need some kind of adapter.........

Motherboard: Gigabyte GA-3CESL: http://b2b.gigabyte.com/products/product-page.aspx?pid=2658#dl Dell Part Numbers for the motherboard: R1232 R1232L R2232S SERVER MOTHERBOARD GENUINE 408P9 CN-0408P9 GA-3CESL Manual Download here RAMSlots: 16 (8 controlled by each CPU) RAMType: DDR2 ECC 5300P........

I'm not sure why I'm getting these but all memory modules are the exact same and all passed memtest successfully although they are ECC. I've heard that ECC RAM can't be tested as well and the kernel seems to indicate they are non-fatl recoverable errors. I wonder if the BIOS has aggressive RAM timing or maybe the controller or motherboard is bad. [ 12.716515] EDAC MC: Ver: 2.1.0 [ 12.717771] EDAC MC0: Giving out device to........

I've got one of these for testing projects from work at home and got more than I bargained for with the time I've spent on it due to the storage handing/Perc 6/i cards. My particular model came with the following: 2U Rack Mount Server with Rails 2xOpteron 2373 EE (Quad Core, there is a 6-core version that can be found at times) 16GB RAM 2 x 250GB Seagate SATA 2 x Dell Perc 6/i (horrible and a nightmare to work........

The results are not bad, the Hitachi performs the same as it does in a SATA2 motherboard. However, the 2TB is much different, on a similar 2TB Toshiba I get about 198MB/s on a different motherboard vs the 2TB Hitachi which should produce similar results. This Dell Perc 6/i is on a PCI x8 riser card and is connected to a 12-port backplane. Adapter #0 Enclosure Device ID: 32 Slot Number: 0 Enclosure position: N/A De........

One thing to remember is that you need MegaCli to do the flashing. You also need the correct file,I tried at least 2 different Perc 6 firmwares from Dell that kept getting rejected as corrupt by MegaCli(they were really the wrong version). I have an external PCI-E Dell 6 Perc/I butI chose images from the 'Integrated" on motherboard version as it was allI could find. They are different, and below is my first time finding success.........

LSi Megaraid At first it was configured as a RAID 0, then I deleted the Virtual Disk Group. I thought both drives would be shown and detected in Linux as sda and sdb but it actually shows nothing. To make them work you have to hit Ctrl+R before the system boots (when prompted) and create a Virtual Disk Group. In my case I created each one as RAID 0 (with a single drive only) as I just wanted JBOD but there is no such option or default in these Dell Pe........

kernel: EDAC MC0: CE page 0x0, offset 0x0, grain 1073741824, syndrome 0x1a, row 2, channel 0, label "": i3200 CE I believe this is a hardware issue, it's usually bad RAM, incompatible RAM or bad timing or even a motherboard/RAM controller.........

This is the most I can get when plugging in a hard drive hot and only on some power connectors. [71656.314271] ata5: exception Emask 0x50 SAct 0x0 SErr 0x90a02 action 0xe frozen [71656.314277] ata5: irq_stat 0x00400000, PHY RDY changed [71656.314285] ata5: SError: { RecovComm Persist HostInt PHYRdyChg 10B8B } [71656.314294] ata5: hard resetting link [71660.360686] ata5: softreset failed (device not ready) [71660.360694] ata5: applying........

I've encountered this problem before and I believe it may affect other drivers (I could test but I don't have time). This was happening on my custom Linux system with the pcnet32 driver. pcnet32: eth0: transmit timed out, status 97fb, resetting (and some other kernel module tracing in dmesg) Basically it means the card is connected (it shows connected in full duplex etc.. and recognized if the cable is disconnected too) but no packets can be sent or received........

For years I've always built cheap systems believing that there is little difference in more expensive components when it comes to reliability and quality, I generally believe this still except for Power Supplies. I've always bought cheap cases with nice sounding 350-550W stock/cheap/crap power supplies and haven't had any issues for the most part until recently. One such case is an NGEAR case with a 550W Optimax power supply, I always read that these supplies don't produce the........

I've thought for awhile that Asus has been banking on its years old reputation for quality amongst gamers and enthusiasts and I think I'm right. My Asus VE247H Monitor with a supposed 2MS refresh rate has 1 red/stuck/dead pixel but fortunately it can only be seen on a non-true black picture or against a blue screen. I have several Asus products and find they're all of fairly poor quality. First of all their motherboards have given me the most issues of any brand, they te........

This is one in a series of weird things whichIthought was motherboard related (I RMA'd the motherboard), the RAM tests fine with memtest86 and I used badblocks on both RAID 1 members with no errors and smartctl is happy with them. Basically the array crashes the kernel a lot and has issues when writing. [112322.723465] md0: rw=0, want=14958668696, limit=1887460480 [112322.731077] attempt to access beyond end of device [112322.731087] md........

ifup eth0 SIOCSIFFLAGS: Cannot allocate memory Failed to bring up eth0 This is on a Centos 5.5 machine with OpenVZ kernel 2.6.18-238.12.1.el5.028stab091.1PAE, I updated 3 systems with the same hardware to the same kernel and for some reason the network didn't come back. This only happened once the first time I booted into the new kernel and hasn't happened again but this is a serious issue for those running systems from remote locations such as a datacente........

My mother needed a new laptop and I recommended her the same one I would have bought myself or my wife, that means the cheapest possible laptop with the most features for the money. This HP shines at this price point and one thing that made me stay away from buying more and recommending HP/Compaq was the poor battery life. Not anymore, this model has an industry leading up to 4 hours of battery life. Key Factors for Choosing It: HDMI Out........

VMWare bridged adapter not working: Message from system: The network bridge on device vmnet0 is not running. The virtual machine will not be able to communicate with the host or with other machines on your network. Failed to connect virtual device Ethernet1. I'm not sure how to fix this but one of the issues is that my eth0 became eth1 after moving my hard drives to a new motherboard. I have run the vmware-config.pl but this did not resolve the issue.........

Do you have an LGA1156 board and wonder why your onboard video isn't working? It's probably because there is no GPU integrated on the board itself, it is supposed to be on the CPU and new CPU's from Intel don't come with it! I was shocked to learn that you can buy a motherboard with onboard video which doesn't work. Inever knew it was being done or possible, but to make it worse the latest Core i5's don't have video on the die of the CPU. This means having on........

I'm not impressed with this motherboard, I was impressed with my Gigabyte AM3 board which seems to work flawlessly. Everyone knows that the firmware is flawed, even though I have the F6, it still seems that the system doesn't reset properly or quickly enough. Another HUGE problem is that in most Linux kernels the NIC won't work (if you try 10 times by rebooting it might). I also notice that you need to power down for it to work. This board does not seem very com........

This was unbelievable how much the Xen kernel slows things down, keep in mind both tests were done on the hostnode, one was with the Openvz-Xen hybrid kernel and the other was just OpenVZ. You can see the performance difference is nearly 300% better when not using the Xen kernel. OpenVZ-Xen Kernel Test Results (I was wondering what was wrong/so slow with my Core i5!) # # # # # #&n........

I took an educated guess because it kept happening at the same spot when loading the XP install. I thought it was the hard drive or motherboard. But it turns out my heavily used but loved NEC 3500 DVD-RW drive was the culprit. After disconnecting it and swapping it for another much beloved Pioneer DVD-RW, everything has gone smoothly. I never ran into this or many issues because I've hardly used this drive since moving it to another Desktop years ago. I actua........

From the package "parted" you can use the command "partprobe" to re-read the partition table. I really hate rebooting, and that's what Iloved to hear about AHCI motherboards, that they allow hotswap so you don't have to reboot. But that's only as good as the OS, if the OS does not reload the partition table you won't be able to do anything with that new drive you attached without rebooting. Yes, even without re-reading the partiton table Linux will........

The New Chips on the BlockThe New Chips on the Block By Bruce Gain Story location: http://www.wired.com/news/infostructure/0,1377,67795,00.html 02:00 AM Jun. 13, 2005 PT We have embarked upon a new era in x86 PC computing -- so say chip giants AMD and Intel following their launches of dual-core PC processors. So how will dual-core processing change your PC computing experience? Our FAQ should help you decide whether or when you sho........

ECS K7S5A Motherboard System Take Up To 2 Minutes To BootHi guys, My motherboard is very strange. Sometimes it will take up to a few minutes to post. I have no idea it suddenly started doing this. I have tried everything and all I can figure is that it is somehow related to the USB ports possibly. Why do I say this? Because if I disconnect my scanner the problem occurs less frequently. I only have a printer hooked up to USB now and by........

Itried everything Icould think of, and of course even with the NIC enabled in the BIOS nothing was working. The light would flash when you plugin the cable for a second, but that's all. Due to another issue I'm about to post about (server is not compatible with 1TB/1000Gig Hard Drives), I updated the BIOS. I didn't even know the 100mbit NICs were not working untilI decided I should test each NIC one by one. Inoticed that only 1 server out of........

This is the Intel Atom 330 motherboard with integrated Realtek Gigabit NIC (Intel Desktop Board D945GCLF2 Motherboard W/ Atom 330 1.6 GHz Dual Core Processor - Mini-ITX) I cannot achieve more than 15 MB/s, even doing a local transfer through eth0 to it's own IP. 100% 95MB 15.9MB/s 00:06 So this is not a cabling, switch or hardware issue, it seems like a driver or chipset limitation problem. Here is my........

Ithink there has been a lot of negative press towards Rackable Systems. We will give their new solution credit that it is marketed very well, and comes prepackaged and ready to go. But let's cut through the hype of both sides, the people who love this concept and the people who hate it. What Rackable Systems have done is a first, to minimize space, power and costs into small servers. This is great, and many companies have already built their own servers based........