• how to use ifplugd in Linux to execute a command or script when a NIC cable is unplugged or plugged in


    It is fairly simple to use once you know how to use it. However, the tricky thing is that by default it doesn't seem to be active or listen on any interface on manually specified. How To Install ifplugd First we install ifplugd sudo apt install ifplugd Let's enable it on our desired device(s) vi /etc/default/ifplugd set this line as so:........
  • python import docx error


    sudo pip3 install python-docx [sudo] password for : Downloading/unpacking python-docx Downloading python-docx-0.8.10.tar.gz (5.5MB): 5.5MB downloaded Running setup.py (path:/tmp/pip_build_root/python-docx/setup.py) egg_info for package python-docx no previously-included directories found matching 'docs/.build' warning: no previously-included files matching '.DS_Store' foun........
  • What happens when you unplug 1 or more devices from an mdadm RAID array to simulate a failure in Linux Ubuntu/Centos/Debian?


    In short the two drives in the array were /dev/sdd and /dev/sde. The kernel sees they were unplugged and have gone down as you can see below. mdadm caught the first one being unplugged /dev/sde and disabled the missing drive. However when the final drive that was part of the array is unplugged it didn't notice at all. Instead it complains about an IO error later for drives that the kernel knows do not exist anymore. [45817.162728] ata4: exception........
  • mdadm and lvm how to completely disable and remove vg/pv/lv


    In short the solution is just to use vgremove for the actual /dev/mapper device: vgremove /dev/mapper/backups-backuplv box mnt # mdadm --manage /dev/md8 --stop mdadm: Cannot get exclusive access to /dev/md8:Perhaps a running process, mounted filesystem or active volume group? box mnt # lv lvchange lvconvert lvcreate l........
  • ADATA SU800 256GB 3D NAND Flash SSD Test & Review


    I keep reading these drives are slower, but they are cheap and still SSDand work very fast for my needs. As you can see the sequential read is 481-491MB/s, if I put them in MDADM RAID10 mode (normal RAID1) they should give me well over 900MB/s and with redundancy and being very cheap for what they offer. [1232206.315622] scsi 8:0:1:0: Direct-Access ATA ADATA SU800&........
  • mcp55 NIC not working at boot on Centos 6.6-6.8


    forcedeth 0000:00:08.0: irq 25 for MSI/MSI-X forcedeth 0000:00:08.0: eth0: MSI enabled forcedeth 0000:00:08.0: eth0: no link during initialization ADDRCONF(NETDEV_UP): eth0: link is not ready forcedeth 0000:00:08.0: eth0: link up ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready Dec 1 18:21:32 box15 kernel: forcedeth: Reverse Engineered nForce ethernet driver. Version 0.64. Dec 1 18:21:32 box15 kernel........
  • Nvidia Linux Card not working due to LSI 9200/SAS2008 IRQ conflict


    At first my BIOS said the card may not work right because there is no more option ROM space. I disabled the Option ROM for both LSI 1068 and 2008 chipsets, Network Boot ROM and most other PCI slots, Serial Port, etc... and the message went away but the card still does not work properly. But it still cannot initialize the card properly(does not work): [ 33.943272] NVRM: This PCI I/O region assigned to your NVIDIA device is invalid:........
  • Linux check NIC ethernet port network card speed


    ethtool eth0 Settings for eth0: Supported ports: [ TP MII ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full ........
  • Linux disable firmware prevents NIC/Ethernet from working phy0 -> rt2x00lib_request_firmware: Error - Failed to request Firmware.


    [ 17.208336] tg3 0000:08:00.0: eth0: Link is up at 1000 Mbps, full duplex [ 17.210194] tg3 0000:08:00.0: eth0: Flow control is on for TX and on for RX [ 76.000065] phy0 -> rt2x00lib_request_firmware: Error - Failed to request Firmware. [ 76.002332] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 86.736004] eth0: no IPv6 routers present [ 148.960038] phy0 -> rt2x00lib_request_fi........
  • Directadmin compile error solution cc: Internal error: Killed (program cc1)


    cc: Internal error: Killed (program cc1) Please submit a full bug report. See for instructions. make: *** [ext/fileinfo/libmagic/apprentice.lo] Error 1 make: *** Waiting for unfinished jobs.... Stopping crond: ........
  • What a hdd hard drive and mdadm RAID array failure looks like in Linux


    [3805108.257042] sd 0:0:0:0: [sda] 1953525168 512-byte hardware sectors: (1.00 TB/931 GiB) [3805108.257052] sd 0:0:0:0: [sda] Write Protect is off [3805108.257054] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [3805108.257066] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [3805108.257083] sd 0:0:0:0: [sda] 1953525168 512-byte hardware sectors: (1.00 TB/931 GiB) [3805108.257090] sd 0:0:0:0: [sda] Write Protect is off........
  • Openvz OOM Centos Issue Memory Config Settings Solution


    Linux box13. 2.6.32-042stab076.5 #1 SMP Mon Mar 18 20:41:34 MSK 2013 x86_64 x86_64 x86_64 GNU/Linux even setting privvmpages to a specific setting DOES not affect "free -m" in containers. This is probably a kernel issue 23:36:29 up 159 days, 7:12, 4 users, load average: 0.42, 0.44, 0.33 [root@box13 ~]# free -m total&n........
  • LSI MegaRAID Adventures, Guide and HowTo


    LSi Megaraid At first it was configured as a RAID 0, then I deleted the Virtual Disk Group. I thought both drives would be shown and detected in Linux as sda and sdb but it actually shows nothing. To make them work you have to hit Ctrl+R before the system boots (when prompted) and create a Virtual Disk Group. In my case I created each one as RAID 0 (with a single drive only) as I just wanted JBOD but there is no such option or default in these Dell Pe........
  • Powersupply Issue, Motherboard AHCI issue?


    This is the most I can get when plugging in a hard drive hot and only on some power connectors. [71656.314271] ata5: exception Emask 0x50 SAct 0x0 SErr 0x90a02 action 0xe frozen [71656.314277] ata5: irq_stat 0x00400000, PHY RDY changed [71656.314285] ata5: SError: { RecovComm Persist HostInt PHYRdyChg 10B8B } [71656.314294] ata5: hard resetting link [71660.360686] ata5: softreset failed (device not ready) [71660.360694] ata5: applying........
  • kvm cannot boot xen guest using lvm


    This booting error is because the Xen PV guest image uses the Xen kernel, this is not compatible with anything but a host running a Xen kernel. I did a kpartx -av virtual.img and then it created some partitions that showed up in fdisk. I mounted it and did a chroot into it and removed the xen kernel and installed a normal kernel but Xen still shows the same kernel in Grub (only the Xen one). This is strange but it seems like this Xen PV guest has some sort of hidden or........
  • Error: detected vswap CT config but kernel does not support vswap This means either old kernel or bad config (physpages NOT set to 0:unlimited) Solution for OpenVZ


    Error: detected vswap CT config but kernel does not support vswap This means either old kernel or bad config (physpages NOT set to 0:unlimited) Solution vzctl set $veid --physpages 0:unlimited --save........
  • KVM QEMU and Xen how to mount disk images off-line and access data


    fdisk -lu VPS.img last_lba(): I don't know how to handle files with mode 81ed You must set cylinders. You can do this from the extra functions menu. Disk VPS.img: 0 MB, 0 bytes 255 heads, 63 sectors/track, 0 cylinders, total 0 sectors Units = sectors of 1 * 512 = 512 bytes Device Boot Start End ........
  • 2011 Best Laptop - HP 15.6" Laptop featuring AMD Athlon II P340 Processor (G62-420CA)


    My mother needed a new laptop and I recommended her the same one I would have bought myself or my wife, that means the cheapest possible laptop with the most features for the money. This HP shines at this price point and one thing that made me stay away from buying more and recommending HP/Compaq was the poor battery life. Not anymore, this model has an industry leading up to 4 hours of battery life. Key Factors for Choosing It: HDMI Out........
  • mdadm RAID 1 adventures


    I separated the 2 drives in the RAID 1 array. 1 is the old one /dev/sda and is out of date, while the separated other one /dev/sdc was in another drive and mounted and used with more data (updated). I wonder how mdadm will handle this: usb-storage: device scan complete md: md127 stopped. md: bind md: md127: raid array is not clean -- starting background reconstruction raid1: raid set md127 active with 1 out of 2 m........
  • Linux 2.6.33.3 Kernel Error CC drivers/message/fusion/mptsas.o drivers/message/fusion/mptsas.c: In function `mptsas_port_delete': drivers/message/fusion/mptsas.c:106: sorry, unimplemented: inlining failed in call to 'mptsas_set_rphy': function b


    CC drivers/message/fusion/mptsas.o drivers/message/fusion/mptsas.c: In function `mptsas_port_delete': drivers/message/fusion/mptsas.c:106: sorry, unimplemented: inlining failed in call to 'mptsas_set_rphy': function body not available drivers/message/fusion/mptsas.c:462: sorry, unimplemented: called from here make[3]: *** [drivers/message/fusion/mptsas.o] Error 1 make[2]: *** [drivers/message/fusion] Error 2 mak........
  • Linux AHCI Hotswap Tips - Remember To Reread The Partition Table WITHOUT rebooting


    From the package "parted" you can use the command "partprobe" to re-read the partition table. I really hate rebooting, and that's what Iloved to hear about AHCI motherboards, that they allow hotswap so you don't have to reboot. But that's only as good as the OS, if the OS does not reload the partition table you won't be able to do anything with that new drive you attached without rebooting. Yes, even without re-reading the partiton table Linux will........
  • Have an OpenVZ VPS/Linux Virtual Private Server and nothing works right?


    A VPS Server I had just wasn't working right, code that I migrated there just wasn't working. For example, it kept telling me the connection to the database was unsuccessful, halfway through iterating through results it already had. Then I realized it wasn't my code. Ichecked my /proc/user_beancounters and found this: cat /proc/user_beancounters Version: 2.5 uid resource held maxheld barrier limit failcnt........
  • Latest Articles

  • Aruba/HP/Dell IAP Wireless Controller Common Default Passwords
  • Debian, Mint Ubuntu how to remove package and associated config files
  • Linux Grub not booting the intended kernel solution in Debian, Mint, Ubuntu how to specify which kernel to boot by default
  • QEMU KVM Keyboard Problems Not Working Right Repeating Characters, Ctrl+C Copy and Paste not working right when using PS2 mouse in guests Solution
  • Linux how to compile binary with static sharedobjects embedded instead of dynamic to use on multi-distributions and avoid glibc compatiblity issues
  • /bin/sh: msgfmt: not found error solution on Linux Compilation Ubuntu Debian Mint Centos
  • Mikrotik RouterOS CHR/ISO Basic and Quick Setup Howto Guide
  • qemu 4 compilation options
  • CentOS 7 8 PXEBoot Netinstall Not Working Solution "Pane is dead "new value non-exisetnt xfs filesystem is not valid as a default fs type"
  • CentOS 6 EOL yum repo won't work Error: Cannot find a valid baseurl for repo: base Solution
  • CentOS 7 8 How To Disable SELinux
  • Wordpress How To Add Featured Image To Post in Hueman Theme
  • kdenlive full reset how to erase all config files
  • CentOS 7 8 yum error Trying other mirror. To address this issue please refer to the below wiki article
  • Microsoft Teams Linux - Calendar Doesn't Work Missed Meetings!
  • Scanner not working in Linux Ubuntu Fedora Mint Debian over the network? Use sane-airscan!
  • How To Boot, Install and Run Windows 2000 on QEMU-KVM
  • bash cannot execute permission denied
  • Huion and Wacom Tablets How To Install in Linux Mint / Ubuntu and make the stylus work properly
  • ffmpeg how to cut certain parts of video out