If you've come here, don't be embarraassed, working in IT, this is the MOST common computer problem that almost everyone will encounter. The reason why I'm doing this post is because I've seen an increase from colleagues and admins having this problem and many times it's not even your fault. A common scenario is that someone acquires a new or used computer which they weren't given the password for. Fortunately Ihave a detailed list of all the options whether free or pa........
I think this is more so an issue with kernel modules not being included. I had this issue on Linux Mint because a new kernel I upgraded to DIDNOT have the "extra" modules and part of that reason is also because older kernels are named differently than new ones.
Take this example article below that shows it in action.
If you were previously........
When running cudaminer once it tries to initialize the card the entire screen freezes. The computer itself is still running but the Xorg is done for, you cannot even switch to another console window and must reboot (even an mdm or Xorg restart does not help).
At first cudaminer will give you these errors:
...retry after 15 seconds
GPU #0: Geforce 210 with compute ca........
i337 Canada on Bell is hard to root or even install TWRP
Installed TWRP from Odin and my computer gave me the bluescreen at the end but it seemed to be successful (after ODIN said reset).
TWRP mode does not seem to enter, instead you get the Android recovery mode with Volume up + Home
The results are not bad, the Hitachi performs the same as it does in a SATA2 motherboard. However, the 2TB is much different, on a similar 2TB Toshiba I get about 198MB/s on a different motherboard vs the 2TB Hitachi which should produce similar results.
This Dell Perc 6/i is on a PCI x8 riser card and is connected to a 12-port backplane.
Enclosure Device ID: 32
Slot Number: 0
Enclosure position: N/A
At first it was configured as a RAID 0, then I deleted the Virtual Disk Group.
I thought both drives would be shown and detected in Linux as sda and sdb but it actually shows nothing.
To make them work you have to hit Ctrl+R before the system boots (when prompted) and create a Virtual Disk Group. In my case I created each one as RAID 0 (with a single drive only) as I just wanted JBOD but there is no such option or default in these Dell Pe........
I chose this because I heard a lot of stories about scams and that many providers I contacted said they can't unlock the Canadian I717s (one said "my Bell server" is down).
This method worked perfectly on my Bell I717M and should work for all I717 in Canada, I was able to insert a foreign SIMcard. This will work abroad too but remember entering CWM mode is different for I717's in other countries (at least theUS).
Step 1 - Root + CWM........
This is based on Debian Linux but should apply equally to any *nix distro.
apt-get install cryptsetup
Setup your LUKS Partition
Of course change /dev/md2 with whatever partition you intend to use LUKS on.
cryptsetup --verbose --verify-passphrase luksFormat /dev/md2
You'll be asked to verify your decryption password twice
*DO NOT FORGET THIS PASSWORD AS IT IS NOT RECOVERABLE!........
This is pretty bad, ever since my phone has been unlocked the battery life is horrible. Many others have reported this issue on provider unlocked phones and even jail broken phones. We're talking issues as bad as losing 1% every 3 minutes which is what I seem to have observed as well.
For now I'm going to relock the phone, and hopefully a firmware update will address this issue. This is very annoying and it seems apparent this is also happening on 3G phones and that........
First of all you need to be jailbroken, but this is not covered here.
Go into Cydia and click "Manage Sources" then "Edit"and add: repo666.ultrasn0w.com
Then search for "ultrasn0w" as a package and install it, that's all there is to it, your iPhone is finally unlocked so when you travel abroad you can avoid ridiculous roaming charges, or you can switch providers and use any SIMcard you like.
You'd really thi........
When trying to even cd or ls the mounted OCFS2 partition it crashes. Ithink this is a combination of VMWare Server's problem and the way I mounted and symlinked to it.
More than anything this shows the problem and lack of forsight with VMWare, but also that OCFS2 is easily crashed if you do strange things.
Output of /var/log/messages for OCFS2
Apr 10 15:57:45 localhost kernel: [84331.691258] Modules linked in: vmnet vmci vmmon ocfs2_stac........