• docker / kubernetes breaks Proxmox QEMU KVM Bridge VMs


    Docker adds iptables rules that break a lot of things including MASQUERADE or anything that needs the FORWARD table. If NAT is not working after Docker installation, it is probably because it set the iptables FORWARD policy to DROP. This may also make you think that your br0 or bridge is not working, but it's likely just due to what we'll mention later on below, that, Docker probably set your FORWARD chain to default DROP all packets, so nothing on your bridge ever makes it out........
  • How To Boot Cisco CUCM UCSInstall 8.6, 10, 11 and 12 on KVM/Proxmox


    The key thing is that you must use a "machine"id of "pc-1.3" or it will say your hardware is not supported. Additionally you MUST use a virtio disk or you will get a ks_pre.sh error as soon as the install starts (a look at logs will show it can't find a disk). This is funny because even though the OS finds the disk and an fdisk -l shows it, it looks like the script looks for a /dev/vda device (virtio) and nothing else, so if you didn't use Virtio as you........
  • proxmox vm networking breaks when you restart your network on the hostnode


    Idid a systemctl restart networking and it broke Proxmox VM connectivity! #proxmox is the problem after restarting the network the tap devices go to disabled state [2230884.919905] vmbr0: port 7(tap118i0) entered disabled state [2230884.948864] vmbr0: port 8(tap122i0) entered disabled state [2230884.972748] vmbr0: port 6(tap119i0) entered disabled state [2230885.004745] vmbr0: port 5(tap117i0) entered disabled state [2230885.03673........
  • Debian/Ubuntu/Mint Linux How To Set VLAN in /etc/network/interfaces


    You can find many ways to specify the VLANin your network configuration but Ifind this is the simplest and quickest. In this case we are talking about a bridged adapter "vmbr0" but it works even if you just had a normal non-bridged interface. The key here is that in vmbr0 you'll notice there is no IP address. We just specify "manual". Below it is a similar stanza for "vmbr0.58" in this case 58 represents the VLAN (change........
  • Latest Articles

  • Recommended SFP+ to RJ45 Adapter Module for Switch Juniper Cisco Ubiquiti TP-Link etc...
  • Bad Power Supply Issue Story Diagnosing Troubleshooting
  • Getting started with AI (Artificial Intelligence) in Linux / Ubuntu using by deploying LLM (Language Learing Models) using Ollama LLMA
  • microk8s kubernetes how to install OpenEBS
  • Flash LSI MegaRAID 2208 to IT mode in Linux Mint/Debian/Ubuntu
  • LSI MegaRAID in Linux Ubuntu / Centos Tutorial Setup Guide megacli
  • Convert-im6.q16: attempt to perform an operation not allowed by the security policy `PDF' @ error/constitute.c/IsCoderAuthorized/413. convert-im6.q16: no images defined `pts-time.jpg' @ error/convert.c/ConvertImageCommand/3258. solution ImageMagick P
  • Apache PHP sending expires header solution cannot use cache with CDN
  • How to install virt-manager in Mint 22/Ubuntu 22
  • Infiniband Guide
  • python mysql install error: /bin/sh: 1: mysql_config: not found /bin/sh: 1: mariadb_config: not found /bin/sh: 1: mysql_config: not found mysql_config --version
  • FreePBX 17 How To Add a Trunk
  • Docker Container Onboot Policy - How to make sure a container is always running
  • FreePBX 17 How To Add Phones / Extensions and Register
  • Warning: The driver descriptor says the physical block size is 2048 bytes, but Linux says it is 512 bytes. solution
  • Cisco How To Use a Third Party SIP Phone (eg. Avaya, 3CX)
  • Cisco Unified Communication Manager (CUCM) - How To Add Phones
  • pptp / pptpd not working in DD-WRT iptables / router
  • systemd-journald high memory usage solution
  • How to Install FreePBX 17 in Linux Debian Ubuntu Mint Guide