• Linux Debian Mint Ubuntu Bridge br0 gets random IP


    This can break things easily in remove environments where it was normally easy to convert a normal eth0 to a bridge under br0, and that bridge would normally have the same MAC address by default, which is desirable for most situations. In Debian 11 this is different for some reason now. https://unix.stackexchange.com/questions/681013/bridge-gets-random-mac-........
  • How to access a disk with bad superblock Linux Ubuntu Debian Redhat CentOS ext3 ext4


    Have you ever tried mounting a partition that you exists but you get this error? mount: /mnt: can't read superblock on /dev/sda1. The superblock in this example was bad because the physical disk had corruption and bad blocks/sectors. However, the data was generally accessible and you can always try this trick below (with caution and no warranty). This is specifically for filesystems that place superblocks in multiple locations, which........
  • Docker Swarm vs Kubernetes Comparison Guide


    A lot of companies are unsure which solution to choose and many may not be aware of Docker Swarm as an alternative to Kubernetes. One thing that many Sysadmins find is that Docker Swarm is simply easier, quicker to setup and maintain by far than Kubernetes.........
  • Proxmox How To Rename Node Hostname Fix Solution


    Proxmox's documentation shows the following here. Which mainly just says change /etc/hosts and /etc/hostname with your new hostname. Here's what happens if you only do that: If you just do the above, you will find you have an inaccessible original hostname that contains those VMs and you cannot........
  • How to use the FTDI USB serial cable to RJ45 adapter to connect to the console on Cisco/Juniper Switch Router Firewall in Linux Ubuntu Debian Redhat


    This should work for most console ports of other manufacturers too. It is a quick and simple method for emegencies or deploying a few appliances/devices in a non-standard environment or small environment. However, if this is a route thing, or the equipment is not physically close to you, it would be best to use some sort of "Terminal" server which is an IP connected switch with several serial ports built-in for this purpose. Normally they accessible by web/........
  • Virtualbox Best Networking Mode In Lab/Work Environment without using NAT Network or Bridged


    Virtualbox is a very powerful tool, but for some use cases it is less than optimal. Say you are in a work, lab or other environment where you are not alone on the physical network and there could be overlap of IPs, but you need all of your VMs to be contactable from your host, VMs need to communicate with each other, and VMs need internet. NAT Network will give you VM to VM communication and internet, however, it is buggy and unstable. It also doesn't allow host to VM co........
  • CentOS 7 / 8 cannot boot with with mdadm RAID array solution


    This article about migrating to a CentOS 7 /8 RAID mdadm array has a lot of info but I wanted to focus specifically on what newer versions of CentOS 7 require to boot mdadm and what changes are necessary on CentOS 7.8+ CentOS 7 / 8 mdadm RAID booting requirements This assumes you are chrooting into an existing install or using it to get a new deployment ready. However, these steps can........
  • ecryptfs How To Backup / Migrate Linux Mint Ubuntu Debian system ecryptfs properly and restore access


    In this scenario, let's say you want to clone your OS at the filesystem level and the source system (the system you want to clone from) is in use. Doing a blind rsync / is a big problem because it uses twice as much space for no reason. The reason for this is that with ecryptfs you have a /home/.ecryptfs directory which has the actual encrypted versions of your files and folders. However your home directory (eg. /home/someuser) is mounted. Doing the blind rsync will ca........
  • Docker Tutorial HowTo Install Docker, Use and Create Docker Container Images Clustering Swarm Mode Monitoring Service Hosting Provider


    The Best Docker Tutorial for Beginners We quickly explain the basic Docker concepts and show you how to do the most common tasks from starting your first container, to making custom images, a Docker Swarm Cluster Tutorial, docker compose and Docker buildfiles.........
  • apache symlinks denied even with followsymlinks


    Symbolic link not allowed or link target not accessible: /path/httpdocs/news.html There are a few reasons that can cause this message and this is for people who have ruled out the basics, eg. your symlinks are enabled and the right permissions are applied (but read on to learn about ownership requirements above the directory in question). So there are a few key things here that cause Apache not to follow symlinks:........
  • Linux Permissions and Groups Real Usecase for Group Access


    Ihave a directory structure which the primary user needs full access on but wanted a user to access only a specific directory within the main directory (so they could write in there only and nowhere else). Here's what Idid: [root@compevo8001 dllnow]# ls -alh drwxrwxr-x 2 someuser software 4.0K Oct 19 2017 ExpireYMD-2017-11-20 drwxrwxr-x 2 someuser software 4.0K Nov 19 2017 ExpireYMD-20........
  • Linux input/output error invalid program cannot read data on some CD-Rs and DVD-Rs on ASUS BW-16D1HT


    I've never seen this before in all of my years. Ihave some very old CDs and DVDs 12-15 years old that seem not to work in this BD-R/DVD-R/CD-R Asus drive. The discs are fine actually and ironically they even work fine on a normal LG USB based BD-R drive! Here are the errors in Linux: [2914936.884924] attempt to access beyond end of device [2914936.884927] loop1: rw=0, want=730424, limit=688384 [2914954.556873] attempt to........
  • How To Secure Samba NMBD/SMBD to bind to a specific IP address


    By default Samba SMB/NMB listen on ANY and ALLIPs on your system by binding to 0.0.0.0. Obviously this is a huge security risk if you have a public facing server with both internal and external access. Usually when a system administrator sets up a samba server their intention is just to share with a LAN. To do this you need to the following options under the [global] section in smb.conf bind interfaces only = yes interfaces = 192........
  • Apache SSL Reverse Proxy Very Slow Solution


    This is a simple fix but not a simple problem and it still doesn't make sense to me. But in a nutshell if your target proxy server works fast when accessing directly over SSL then this may be your issue. It seems SSL does not play nicely when the target proxy destination/host has a riduculously long key (such as 8192 bits long). Now this is normally not a problem, in fact the target server could be accessed with hardly any delay directly despite such a long key.........
  • Avocent Unable to load resource avctVideo.jar


    Avocent Unable to load resource avctVideo.jar Avocent requires port 80 and 443 to be forwarded or you will get a message like above if it's on a NAT network and you are accessing it from the outside (internet).........
  • phpBB create new email hash manually when modifying or adding user manually directly through MySQL


    Many may ask why would you need to do this? When upgrading from phpBB 2 to 3 the conversion does not keep the admin user you create. If your old admin user has an email address associated that no longer works or is accessible this makes it impossible to reset the admin password. Some may just say "I'll just manually edit the e-mail address" but it won't work and phpBB will fail to find that user if you don't update the "user_email_hash" field but how do........
  • LVM Tutorial how to create a Physical Volume (PV), Volume Group (vg), and a Logical Volume (LV) within it


    # first we need a physical volume which we use the pvcreate tool to create # I create mine on /dev/sdb3 pvcreate /dev/sdb3 dev_is_mpath: failed to get device for 8:19 Physical volume "/dev/sdb3" successfully created # pvdisplay shows the newly created volume pvdisplay "/dev/sdb3" is a new physical volume of "1.35 TiB" --- NEW Physical volume --- PV N........
  • Either the lower file is not in a valid eCryptfs format, or the key could not be retrieved. Plaintext passthrough mode is not enabled; returning -EIO


    I'm using ecryptfs and was suddenly unable to access or even ls my home directory (but every subfolder is accessible). It just hangs and throws this message in messages/dmesg: Either the lower file is not in a valid eCryptfs format, or the key could not be retrieved. Plaintext passthrough mode is not enabled; returning -EIO I read somewhere that perhaps some file or folder is owned by root somehow, sure enough there are some and sudoing to root allows me to........
  • Samsung Galaxy Note Upgrade to ICS 4.0 microSDHC card not detected/dataloss after upgrading - possible solutions


    I backed up everything in the /mnt/sd_card directory thinking that some dataloss could occur for some reason but purposely left my microSDHC unbacked up thinking that "it won't touch that since it's external" and Samsung's and other manufacturers website even say this (that it won't be affected and not to worry etc). Apparently I was wrong, my microSD was "undetected" and asked to be formatted after the upgrade (there goes 3-months worth of family photos). No........
  • Firefox 11 solution for hidden tabs to the right


    After about 15 tabs I believe, they become hidden on the right side and are accessible only by furiously clicking the "right arrow" and even then it takes forever and honestly this hidden tab feature seems to slow down everything. If you enter "about:config" in your browser without the quotes just set this value to get rid of this annoying (one of many new) feature from Firefox (set it to false and restart your browser): services.sync.prefs.sync.brows........
  • OpenVPN don't use bridgestart.sh or bridge at all use iptables


    I used the suggested script to bridge from OpenVPN and it took my client's server off-line! Don't ever use their "sample" scripts if you don't have another way of accessing the server than SSH. I actually found it easier to use iptables to tell it to route IPs based on a certain subnet to route through eth0: iptables -t nat -A POSTROUTING -s 192.168.200.0/24 -o eth0 -j MASQUERADE Replace "192.168.200.0/24" with your subnet of cour........
  • Yahoo Mail (email) DNS Server Out Of Date Problems


    I don't expect this to be solved soon but some of Yahoo's DNS servers are out of whack. I changed the IPs of some nameservers of some domains and now most Yahoo users can't e-mail to those domains! As you can see below by the "No MX or A records for mychangedomain.com", now Yahoo's DNS/mailserver DNS cache is wrong. You would think they would at least have cached the old incorrect records, but instead for some reason their DNS cache has no entry and doesn't seem........
  • VirtualBox Error Failed to start the virtual machine Centos 5.5 Mirror. Medium '/home/testuser/.VirtualBox/HardDisks/Centos 5.5 Mirror.vdi' is not accessible. UUID {a1a9fad7-0402-4867-b8f3-39fb49454bc5} of the medium '/home/testuser/.VirtualBox/HardD


    Virtualbox Error I tried to copy a .vdi of one container to use in another one, basically to clone instead of having to install the OS again. Failed to start the virtual machine Centos 5.5 Mirror. Medium '/home/testuser/.VirtualBox/HardDisks/Centos 5.5 Mirror.vdi' is not accessible. UUID {a1a9fad7-0402-4867-b8f3-39fb49454bc5} of the medium '/home/testuser/.VirtualBox/HardDisks/Centos 5.5 Mirror.vdi' does not match the value {4945a0e8-0ed5-4736-9088-bcaf........
  • Local policy does not permit you to log on interactively. - Solution/Fix


    For a standalone system the solution is simple, just use the same version of Windows a copy a good version of: C:windowsSecurityDatabasesecedit.sdb from another computer. Then you should be able to login again without getting the nasty message "Local policy does not permit you to log on interactively." Of course you will probably need a way of accessing the filesystem off-line in order to get to it such as a Linux boot disc. Some........
  • FUSE/Curlftpfs mount ftp account as drive partition in Linux


    This is a great way to use your ftp server space, for example on your web hosting account (althoughI believe many hosts don't allow storage like this), but if you have a VPS/Dedicated Server etc.., this would be perfect. Imagine how easy it is to work with an ftp account that you can just mount as a normal partition or directory in Linux, it would be great for backups etc.. Name curlftpfs - mount a ftp host as a local directory Synopsis........
  • Debian 5.04 RAID 1 mdadm boot problem GRUB error


    I successfully created a single RAID 1 partition which includes /boot inside it and my root directory through the Debian installer. It said GRUB installed successfully but when I try booting the OS it seems GRUB can't read anything. When trying to boot from GRUB GRUB Loading stage 1.5. GRUB loading, please wait... Error 2 I get "Error 2" when trying to boot Debian. I also notice from a LiveCD that........
  • Canel Default VHOST DocumentRoot/Contents Directory is /usr/local/apache/htdocs


    This can be very annoying and CPanel doesn't seem to document it, or it's not found or made as obvious as it should be. It's always funny when I find it more difficult to work with a control panel than to do everytihng manually without CPanel or even Plesk. So once again, the default serve path for contents is: /usr/local/apache/htdocs and this is especially applicable when accessing Apache by just an IP which is unbound to any domain at this point.........
  • Picking an FTPD (vsftpd) Server in Linux Centos/Debian


    I decided on using yum to help me decide even though I normaly use proftpd I decided to see what else I could find. yum search ftp Loaded plugins: fastestmirror Loading mirror speeds from cached hostfile * rpmforge: ftp-stud.fht-esslingen.de * base: mirrors.netdna.com * updates: updates.interworx.info * addons: yum.singlehop.com * extras: mirrors.netdna.com rpmforge........
  • Tyan S2735-8M Maximum Hard Drive Limit/Not Working/Doesn't work with 1TB 1000GB hard drives


    Inever saved any of the logs, but basically no matter what OS (Linux)I used, I could not get my 1000GB hard drive to work (Seagate SATA). The BIOS recognizes the drive and fdisk -l shows the hard drive as it should. The tricky thing is that different OS's will give you different results, but don't be fooled. You can't use these larger drives for long. Iwas getting all kinds of seek/IOerrors and also messages that the port could not be read.........
  • Latest Articles

  • Cloned VM/Server/Computer in Linux won't boot and goes to initramfs busybox Solution
  • How To Add Windows 7 8 10 11 to GRUB Boot List Dual Booting
  • How to configure OpenDKIM on Linux with Postfix and setup bind zonefile
  • Debian Ubuntu 10/11/12 Linux how to get tftpd-hpa server setup tutorial
  • efibootmgr: option requires an argument -- 'd' efibootmgr version 15 grub-install.real: error: efibootmgr failed to register the boot entry: Operation not permitted.
  • Apache Error Won't start SSL Cert Issue Solution Unable to configure verify locations for client authentication SSL Library Error: 151441510 error:0906D066:PEM routines:PEM_read_bio:bad end line SSL Library Error: 185090057 error:0B084009:x509 certif
  • Linux Debian Mint Ubuntu Bridge br0 gets random IP
  • redis requirements
  • How to kill a docker swarm
  • docker swarm silly issues
  • isc-dhcp-server dhcpd how to get longer lease
  • nvidia cannot resume from sleep Comm: nvidia-sleep.sh Tainted: Linux Ubuntu Mint Debian
  • zfs and LUKS how to recover in Linux
  • [error] (28)No space left on device: Cannot create SSLMutex Apache Solution Linux CentOS Ubuntu Debian Mint
  • Save money on bandwidth by disabling reflective rpc queries in Linux CentOS RHEL Ubuntu Debian
  • How to access a disk with bad superblock Linux Ubuntu Debian Redhat CentOS ext3 ext4
  • ImageMagick error convert solution - convert-im6.q16: cache resources exhausted
  • PTY allocation request failed on channel 0 solution
  • docker error not supported as upperdir failed to start daemon: error initializing graphdriver: driver not supported
  • Migrated Linux Ubuntu Mint not starting services due to broken /var/run and dbus - Failed to connect to bus: No such file or directory solution