• mdadm force resync when resync=PENDING solution


    cat /proc/mdstat Personalities : [linear] [multipath] [raid0] [raid1] [raid10] [raid6] [raid5] [raid4] md127 : active (auto-read-only) raid10 sdc1[0] sdb1[2] 1953382400 blocks super 1.2 512K chunks 2 far-copies [2/1] [U_] resync=PENDING bitmap: 15/15 pages [60KB], 65536KB chunk Solution force repai........
  • Why SMART is not smart at all and doesn't properly predict disk errors that cause a kernel panic or crash


    Before getting into the output here is my typical experience with SMART, there is what I call a "bad disk" with pending and uncorrectable sectors that cannot be reallocated. It has caused a kernel panic and system crash repeatedly as we can see from the logs. But SMART says it has "PASSED" its self assessment. SMART is still useful to me but it is more about looking at Current_Pending_Sector. Any time I have had anything but 0 for that attribute it........
  • How Does Cisco CUCM (Cisco Unified Communication Manager) Work?


    Cisco's CUCM (Cisco Unified Communication Manager) is a system that combines voice, video, data and mobile products into a single unified management suite. At its core, the CUCMis like a "Super PBX" that controls the flow of all communications through an organization even single or multiple site deployments. Cisco's CUCMmakes communication more effective and simple through centralized management and unification of communications resources.........
  • Ethereum Client Errors


    INFO [07-19|12:11:51] Imported new block receipts count=590 elapsed=8.440s bytes=74117699 number=4870906 hash=6bc60b…934753 ignored=0 INFO [07-19|12:11:57] Imported new state entries count=499 elapsed=9.963ms processed=71076 pending=1526 retry=2&nbs........
  • USB 3.0 External HDD Enclosure Seagate UAS problems - [sdd] tag#1 CDB: Write(16) 8a 00 00 00 00 01 70 04 08 68 00 00 00 08 00 00


    This is a 8TB Seagate external USB 3.0 device apparently newer kernels use a module called "UAS" instead of "USB Storage" which causes issues as a lot of devices are not properly supported in UAS mode by the kernel driver. The solution some say is to disable UAS specifically for your USB device but I'd rather just disable UAS altogether. Solution blacklist UAS: *do not do this it does not work and just causes your USB 3.0........
  • rsync run as root sudo without password


    This is a common issue, what if a issue shouldn't have root but you want to use that user to make a full backup of a system? They of course need root access. You can actually just give them passwordless sudo access to rsync in /etc/sudoers: sudo vi /etc/sudoers yourusername ALL = NOPASSWD: /usr/bin/rsync Here is how you would execute rsync: The key thing for the remote host is to........
  • mdadm frozen and doesn't realize array is dead/missing failed due to unplugged drives


    This was a surprising bug but I unplugged all drives for an array md127. At first it was just 1 drive and mdadm seemed to notice this. I unplugged the second drive taking the array offline but mdadm did not realize it was offline and still showed a non-existent disk as being part of it. This created problems trying to unmount it or even to stop this array with mdadm freezing. As for how to fix it I can only think of making sure you are not in a mounted path of........
  • Thunderbird Error An error occurred while loading or saving configuration information for thunderbird. Some of your configuration settings may not work properly.


    This error seems to happen randomly and especially when trying to send e-mails. Apparently it's a long-standing GNome bug but is also partially the default of Thunderbird depending on who you ask. There is no known fix that I'm aware of except to upgrade gnome and the gvfs package but this is not an option for older versions/distributions. An error occurred while loading or saving configuration information for thunderbird. Some of your configuration settings may not........
  • CPanel suhosin install failed


    /scripts/phpextensionmgr install PHPSuHosin Updating md5sum list Fetching http://httpupdate.cpanel.net/cpanelsync/easy/targz.yaml (connected:0).......(request attempt 1/12)...Resolving httpupdate.cpanel.net...(resolve attempt 1/65)... Fetching http://httpupdate.cpanel.net/mirror_addr_list (connected:0).......(request attempt 1/3)......connecting to 74.50.120.123...@74.50.120.123......connected......receiving...100%......request success......Done........
  • WD 20EARX Dead Again


    Another new drive bad from the start: Jun 2 15:14:18 one-desktop kernel: [15895.386779] ata2.00: exception Emask 0x50 SAct 0x1 SErr 0x280900 action 0x6 frozen Jun 2 15:14:18 one-desktop kernel: [15895.386782] ata2.00: irq_stat 0x08000000, interface fatal error Jun 2 15:14:18 one-desktop kernel: [15895.386784] ata2: SError: { UnrecovData HostInt 10B8B BadCRC } Jun 2 15:14:18 one-desktop kernel: [15895.386788] ata2.00: cmd 60/0........
  • WD 20EARX 2TB Bad within days


    This is just trying to read 5GB off the drive with dd and the drive initially tested ok but shortly after I wondered why I was seeing 2MB/s read speeds. Notice the "current_pending_sector", anytime I've seen it at anything above 0 even with no other bad fields/attributes, it means the drive is bad. ata1.00: exception Emask 0x0 SAct 0x3 SErr 0x0 action 0x0 ata1.00: irq_stat 0x40000008 ata1.00: failed command: READ FPDMA QUEUED ata1.00: cmd 60/00:00:........
  • Bad Hard Drive Slows Down Computer


    Here's a proven example of what a bad hard drive can do, it was technically functioning OKin a RAID array but the system became extremely low and the load become high and IOWAIT was even higher and I always thought it was a bad application. The truth is that this failing 1TBHitachi has slowly gotten worse and caused huge slowdowns, (eg. 100% load on Thunderbird waiting for e-mails to load etc..). After swapping it out, tabs change instantly, emails are not lagged, and........
  • How to log all PHP based E-mails for abuse


    Step #1 - Create Wrapper Script vi /usr/local/bin/phpsendmail #!/usr/bin/php ........
  • Thunderbird How-To Copy/Backup/Restore Accounts and Settings to Another Computer


    The best way is to use rsync, I've set it up so it doesn't copy unnecessary files, or at least ones I'm sure aren't needed. Here is the rsync command Iused (adapt to your specific Thunderbird profile location): rsync -hazv user@remotehost.com:/home/user/.thunderbird/sbrer.default/* /home/user/.thunderbird/4nyb0.default/ --exclude=global* --exclude=Cache --exclude=ImapMail --exclude=Mail This is a great way to get your e-mail accounts going on a new c........
  • mdadm how to add a device to an array after a failure


    This array is a RAID 1 and in this case 1 of the 2 drives failed (a WD drive and I've found them to be the weakest and most unreliable of any brand and are easily damaged/DOA when shipping them). mdadm --manage /dev/md0 --add /dev/sdb1 The above assumes the array you want to add to is /dev/md0 and the device we are adding is /dev/sdb1 *One thing to remember is to make sure the partition you are adding is the correct size for the array. You can also g........
  • How To Test If Your Hard Drive Is Good/Signs of dying hard drive


    I like dd, although it only reads it, usually a read test of the entire disk will uncover if your hard drive is bad in some parts. This is a good thing to do at least once a month, a lot of times bizarre program behavior, laginess and crashing/unnmounting problems etc.. are due to a failing disc and SMART won't know it or indicate a problem: We must also remember there's never a guarantee, I've found that ever since we moved to larger and more platters per drive with 1TB drives........
  • smart is not smart, it thinks a dead drive is still good


    I had a dying drive that smart thought until it totally disappeared was a good drive, and actually all parameters did look fine but this system was causing my system to lockup and other bad behavior: === START OF INFORMATION SECTION === Device Model: WDC WD20EARS-00MVWB0 Serial Number: WD-WMAZ20139 Firmware Version: 50.0AB50 User Capacity: 2,000,398,934,016 bytes Device........
  • Hitachi 2TB HDS5C3020ALA632 drive DOA


    I had one of these shipped and it was not recognized when plugged in, here's what a dead drive looks like (I assume it's teh circuit board which is dead): ata1: link is slow to respond, please be patient (ready=0) ata1: softreset failed (device not ready) ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata1: link online but device misclassified, retrying ata1: link is slow to respond, please be patient (ready=0) ata1: softreset f........
  • Installing Webmin & Enabling SSL


    Webmin Setup Centos 5: wget http://downloads.sourceforge.net/project/webadmin/webmin/1.530/webmin-1.530-1.noarch.rpm?r=http%3A%2F%2Fwww.webmin.com%2Fstandard.html&ts=1294339690&use_mirror=surfnet [1] 24229 [2] 24230 [root@host ~]# --2011-01-06 21:48:20-- http://downloads.sourceforge.net/project/webadmin/webmin/1.530/webmin-1.530-1.noarch.rpm?r=http%3A%2F%2Fwww.webmin.com%2Fstandard.html Resolving downloads.sourceforge.net... 216.34.181.........
  • WD (Western Digital) Advanced Format Drive Lagged/Slow Speed/Performance/Design Flaw EAD/EARS problem WDC WD20EARS-00S8B1


    Let the numbers speak for themselves, from what I read the Load_Cycle_Count which is very high (more than 500,000/half a million times) is the number of head parks. What a stupid"Green" design and design flaw which will probably mean an early life for the drive. This is almost as silly as Seagate's new reputation for BSY/poor quality disks since the 7200.11 series. To make it worse this is also when Western Digital introduced "Advanced Format" o........
  • mdadm "auto-read-only" Linux Software RAID solution


    If you have the "(auto-read-only)" beside an arrayI have no idea why that happens but it is easy to fix. Just run "mdadm --readwrite /dev/md1" (rename md0 to the device with the problem and it will begin to resync. md1 : active (auto-read-only) raid1 sdb2[0] sda2[1] 19534976 blocks [2/2] [UU] resync=PENDING ........
  • Seagate Drive 500GB Drive Dying


    This drive is clearly on the way out, the Kernel knows it but I'm surprised that SMART is not concerned. I didn't blame Seagate for their past issues until now. This hard drive has hardly been used and has not even been powered on for a year according to SMART. Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.11 Device........
  • Seagate 7200.11 firmware defect in 500GB, 1000GB (1TB) and 1500GB (1.5TB) Hard Drives


    Seagate Inventory/Firmware Check I heard about this issue a long time ago but never looked into it. I figured I wasn't affected since my 500GB drives were running for so long. I've been using Seagate's since 2002 and to this day all of the drives I have are alive from Seagate. *Update the bad news is that I realize one of my 500GB's is about to die, it's not even a year old, but is also not affected by the recall according to Seagate! Seagate Inventory/Firm........
  • Package management


    Package managementIf you're like me and often like using an older version you'll need to know this. Since all 5.x versions no longer have packages of their own you'll have to use the 5-stable The best way is to set the [b:d5e8972240]packagesite environment variable[/b:d5e8972240] like so in your [b:d5e8972240].profile [/b:d5e8972240]file [quote:d5e8972240]vi /etc/.profile[/quote:d5e8972240] Add this: [code:1:d5e897224........
  • NEC ND-3500A is great!


    NEC ND-3500A is great!I just picked up an NEC 3500A a few weeks ago and I love it. It is a great all in-one optical drive solution. It can burn DVD/+R-R at up 16x, read at 16x and rewrite at 4x and CD-R at up to 48x! Not bad, but the impotant part is that it delivers consistent high quality burns and the drive is as quiet as I could ask it to be. It's also convenient that it has a lot of hacked firmware for overspeeding of........
  • Latest Articles

  • Linux How To Create A RamDisk
  • mdadm force resync when resync=PENDING solution
  • Proxmox Breaks Storage/LVM Backing If Killing QEMU-IMG
  • Proxmox trying to acquire lock... TASK ERROR: can't lock file '/var/lock/qemu-server/lock-102.conf' - got timeout
  • Debian 9 SSH root password authentication failure password not working problem / solution
  • QEMU / KVM How To Manually Create Basic Virtual Machine VM
  • Linux wlan0 check all wireless clients
  • PHP Issues With Decoding Strange Smart Quotes And Non-Standard ASCII Characters
  • /etc/iproute2/rt_tables default settings file in Linux Centos 6,7 and most other NIX's
  • bind named error solutions named[2169]: error (no valid DS) resolving / error (broken trust chain) resolving / : error (no valid RRSIG) resolving 'com/DS/IN':
  • iptables how to log ALL dropped incoming packets
  • How To Edit Linux Based NM Network Manager Connection Settings Without GUI
  • Linux Disable IPV6 Centos / Debian / Mint Howto
  • Linux use growisofs to burn a larger file on a BD-R / Bluray Disc
  • Linux partprobe/partx cannot access last and 4th partition
  • DRBD Errors Caused By Physical Corruption
  • mdadm: add new device failed for /dev/sdb4 as 3: Invalid argument solution
  • Linux named / bind how to dump, view and clear the cache!
  • Centos 6 / 7 / 8 How To Change Default nameservers in /etc/resolv.conf when using DHCP / dhclient
  • Adobe Acrobat Reader for Linux to use and view XFA Fillable Forms