-?????????? ? ? ? ? ? shadow
----------. 1 root root 748 Jul 10 04:35 shadow-
cat: shadow: Input/output error
If you see this you are probably in big trouble, it could be a physical error or if it's a VM image that it is corrupted due to a physical error on the underlying disk/array/NAS or it could a........
Opening Firefox from the CLI reveals the following as the cause of the error:
Query failed: Error: Error(s) encountered during statement execution: no such table: moz_favicons
The symptoms of this issue are that in the address bar you cannot hit enter to browse to a site/url/address and your history cannot be accessed, nor does your history show up in the address bar when typing previously used addresses.
This usually happens because you've........
You get errors like below and see you have all question marks for the permissions if you go to /run/user/1000/gvfs
If you try to access the mounted share such as anything mounted as gvfs like an SSH share in your file manager you may get an error like this. It generally means an interruption in communication or a fault with gvfsd has caused it.
This is a simple fix but not a simple problem and it still doesn't make sense to me.
But in a nutshell if your target proxy server works fast when accessing directly over SSL then this may be your issue.
It seems SSL does not play nicely when the target proxy destination/host has a riduculously long key (such as 8192 bits long). Now this is normally not a problem, in fact the target server could be accessed with hardly any delay directly despite such a long key.........
There are a few ways of doing this and all basically involve using the reverse proxy or "ProxyPass" feature of Apache to accomplish it.
1.) Create a normal vhost and simply symlink the root directory of the site you want to mirror.
Eg. originalsite.com and newsite.com
You would symlink like this:
ln -s /vhosts/originalsite.com/httpdocs vhosts/originalsite.com/........
1.) Flash directly to this file:
*I was never able to get the larger "Mega" file to work, at least not initially so I recommend the file above.
To enable 5ghz I had to do the "Clear NVRAM" Option before it was shown.
2.) Or if you don't need 5ghz (most devices do not support it and cannot........
The following assumes the computer is local/physical to you and/or it always has a LANIP so it can be accessed on site without having a default gateway.
The key to this is not to set a default gateway for your computer or you can set a script on boot or other time to delete the gateway (where eth0 is the NIC you are using):
route del default eth0
126.96.36.199 is the VPN server you connect to
192.168.1.1 is your........
That is pinging to the gateway IP on the same switch, the same IP is pingable externally without any problems which makes me think the switch is fine.
64 bytes from 188.8.131.52: icmp_seq=4 ttl=255 time=1.07 ms
64 bytes from 184.108.40.206: icmp_seq=1 ttl=255 time=3536 ms
64 bytes from 220.127.116.11: icmp_seq=2 ttl=255 time=2536 ms
64 bytes from 18.104.22.168: icmp_seq=3 ttl=255 time=1536 ms
64 bytes from 22.214.171.124: icmp_seq=8 ttl=255 time=1.20 ms
The most basic is the start menu, which is accessed with Alt+F1........
I installed 5.5 with a 300GB RAID 1 partition (boot is also on this partition). It booted up fine the first few times until after I used a Live CD and accessed the array, and it became named /dev/md127 for some reason.
Now whenI boot into CentOS I get a kernel panic and different errors, once I got "invalid superblock", even though the array is fine (it didn't happen again, probably because I was sure to dismount and stop the mdadm array properly).
This is something that happens a lot and it is very dirty, as you probably know each site is hosted on a certain IP address. Sometimes a domain is hosted by a single IP address and the IP address defaults to this very same domain.
This means that if someone buys domain abcd.com and enters your IP address (the one of your website) as the A record, your content will show up on their domain as if it was their own.
There is an easy way to prevent this by using .htacces........
Server not using user level security and no password supplied.
tree connect failed: NT_STATUS_WRONG_PASSWORD
That happens when trying to use smbclient to connect to a share. The weird thing is that I can authnenticate just fine from Windows XP.
It is partially my mistake, I forgot this share does have a password. I've tried authenticating with the correct user and also with "Guest" because this works in Windows. In Linux I ........