Edit your /etc/hostapd/hostapd.conf file like below and restart hostapd. #WPS stuff # Enable control interface for PBC/PIN entry wpa_psk_file=/etc/hostapd/hostapd.psk ctrl_interface=/var/run/hostapd eap_server=1 wps_state=2 ap_setup_locked=1 wps_pin_requests=/var/run/hostapd.pin-req config_methods=label display push_button keypad #WPS model info stuff change to suit your needs d........

Are you getting this error when trying to connect to a site/domain/service and then you checked your router/nameserver's logs to see what's wrong? You may see something like this: named[3025898]: REFUSED unexpected RCODE resolving This is not usually an error with named or bind, at least not on your end but NORMALLY this is an issue with the remote nameserver. A lot of times this is a misconfigured remote nameserver. A classi........

The easiest way for the current running kernel is: update-initramfs -u -k `uname -r` You could change -k to a specific kernel name if for some reason the current is not running (eg. if you are chrooted or in recovery mode). If you want to update all kernels then use "-k all" update-initramfs -k all -u update-initramfs: Generating /boot/initrd.img-5.4.0-162-generic........

If you are using mint, delete the preference that stops snap from installing (as it is required for lxc) sudo rm /etc/apt/preferences.d/nosnap.pref 1. Install lxd: sudo apt install lxd Issues install lxd or errors? Click here Debian at this time does not have lxd so you'll need to use snap: sudo apt in........

I was using a small box as a router and one of the ports started going off and coming back at 100M. I truly believe it is simply that it was a case of overheating. Although CPUtemps were only about 67 degrees, the physical box itself was almost burning hot. Isolved the cooling issue and never had the issue again. Jul 28 15:09:27 swithbox kernel: e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx Jul 28 15:09:28 swithbox kernel:........

Starting httpd: httpd: Syntax error on line 221 of /etc/httpd/conf/httpd.conf: Syntax error on line 6 of /etc/httpd/conf.d/php.conf: Cannot load /etc/httpd/modules/libphp5.so into server: /etc/httpd/modules/libphp5.so: cannot open shared object file: No such file or directory This is basically caused by the PHPmodule specified in php.conf being non existent. The error tells us it couldn't fnd /etc/httpd/modules/libphp5.so........

ValueError: new value non-existent xfs filesystem is not valid as a default fs type Pane is dead From what Iread this is misleading and has to do with the fact that the initrd and kernel are mismatched. This is a hard situation because for some older hardware Iam using the Centos Plus kernel which has modules that Irequire for an older server/NIC. This seems to have cropped up in the past few months and there is no simple fix........

This was a surprising bug but I unplugged all drives for an array md127. At first it was just 1 drive and mdadm seemed to notice this. I unplugged the second drive taking the array offline but mdadm did not realize it was offline and still showed a non-existent disk as being part of it. This created problems trying to unmount it or even to stop this array with mdadm freezing. As for how to fix it I can only think of making sure you are not in a mounted path of........

The solution is simple but strange, if you copy your /var/lib/mysql directory to another server and think it will work, be sure to check if you have /var/log/mysql and binary log files. If you do, the server will not work and will give you errors like below and crash without the proper log files. UPDATE user SET password=password("newpass") WHERE user='root'; flush privileges; ERROR 2013 (HY000): Lost connection to MySQL server durin........

[ 17.208336] tg3 0000:08:00.0: eth0: Link is up at 1000 Mbps, full duplex [ 17.210194] tg3 0000:08:00.0: eth0: Flow control is on for TX and on for RX [ 76.000065] phy0 -> rt2x00lib_request_firmware: Error - Failed to request Firmware. [ 76.002332] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 86.736004] eth0: no IPv6 routers present [ 148.960038] phy0 -> rt2x00lib_request_fi........

Jul 11 15:20:58 tor sendmail[9617]: r6AKjOD07: to= mailserver.com was the hostname of the server, sendmail sends this by default and many mailservers will reject mail to a hostname that does not resolve or exist. The easiest way is just to change the hostname and make sure it does resolve to something. I read there is a way in sendmail.mc to manually set a hostname but I never got it working: vi /etc/mail/sendmail.mc define(`confDOMAIN........

This booting error is because the Xen PV guest image uses the Xen kernel, this is not compatible with anything but a host running a Xen kernel. I did a kpartx -av virtual.img and then it created some partitions that showed up in fdisk. I mounted it and did a chroot into it and removed the xen kernel and installed a normal kernel but Xen still shows the same kernel in Grub (only the Xen one). This is strange but it seems like this Xen PV guest has some sort of hidden or........

I thought only a faster CPUand SSDwould help but I already have a Quad-Core CPU and it wasn't being maxed out. The actual tests were performed on an AMD-V enabled 128MB dual core VMWare container though. There is a flag that can be passed to make in order to start multiple threads, by specifying 4 threads I was able to reduce the whole kernel compilation time from scratch by about 50%! (65minutes vs 31minutes!). *Yes I did do a make clean before each co........

auth/auth_util.c:make_server_info_sam(840) User nobody in passdb, but getpwnam() fails! I never found the solution to this in the web, as usual so Ithought I'd post the fix. In plain English smbd is telling us that the user "nobody" does not exist in /etc/passwd. You can simply add this to your /etc/passwd file like so: nobody:x:65534:65534:nobody:/nonexistent:/sbin/nologin Now SAMBA/smbd should........