If you have swarm services and dockerd is creating a high load even with the containers just being idle, the easiest solution is to upgrade to a newer docker version. For example an identical config of 3 nodes, with Redis 5 with 30 replicas produces a load of about 1.45 in Debian 10 with Docker18.09.1 If I create the same setup on Debian 11, with Docker 20.10.5+dfsg1 then the CPU usage is low. One other difference I wondered is the kernel. In my test setup........

Enable "cli" mode equivalent in JunOS cli Configure Mode configure So rather than going to the console on a Cisco switch and typing "enable" and then "conf t", the equivalent in JunOS is "cli" and "configure". How Do You Apply Changes You've Made? You can make all kinds of changes to the switch, but remember they are not........

grub> root (hd0,0) root (hd0,0) Filesystem type is ext2fs, partition type 0xfd grub> setup (hd0) setup (hd0) But if you do: root (hd1,0) setup (hd1) it does work, I think hd0/sda had a GPT partition that was not removed properly (what I did was just dd bs=512 count=1 the partition table from another drive since the partition table should be identical). Checking if "/boot/grub/........

INSERT INTO articles_backup SELECT * FROM articles WHERE articleID="118" It is so simple we always recommend people do this when updating their database so you always have a backup. The above inserts the copy into the table "articles_backup" which has an identical structure. It selects the entry from "articles" where the articleID is "118" but of course you can adapter yours to whatever the situation is.........

Use netstat with the -anpe option. The e option shows the inodes and I do not know if it will always work or if it was by fluke but I was dealing with dozens of SSHsessions and needed to know which session was related to which forward (the PIDs of the SSHand SSHD did not match etc...) Notice the "59560675" and "59560762" those are almost identical, if you find two sets that are nearly identical except for the last 3 digits they may match (in my ca........

Motherboard: Gigabyte GA-3CESL: http://b2b.gigabyte.com/products/product-page.aspx?pid=2658#dl Dell Part Numbers for the motherboard: R1232 R1232L R2232S SERVER MOTHERBOARD GENUINE 408P9 CN-0408P9 GA-3CESL Manual Download here RAMSlots: 16 (8 controlled by each CPU) RAMType: DDR2 ECC 5300P........

You need to use the Samsung driver but specify it as a CLP-360 (this is what I used for my CLP365) and incidentally most of these units look identical on the outside on inside (I've been buying whatever the latest C300 and now 400 unit for years which all seem the same with slightly different features that I never use). The solution Once again try specifying earlier models and revisions if the printer doesn't print (it will say it's been sent to the printer bu........

It's weird because I have a nearly identical box and setup and I can update the ovzkernel-PAE* just fine but on this box it doesn't work. I only get this error with the openvz.repo and not others such as Centos-Base.repo With my other server it works normally: ================ Setting up Update Process Resolving Dependencies --> Running transaction check ---> Package ovzkernel-PAE.i686 0:2.6.18-238.12.1.el5.0........

I was creating a RAID array and got this error: mdadm: /dev/sda1 is too small: 0K mdadm: create aborted Of course sda1 is not too small, both partitions sda1 and sdb1 are identical in size: Disk /dev/sda: 2000.3 GB, 2000398934016 bytes 255 heads, 63 sectors/track, 243201 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x00000000 Device Boot Sta........

Before we start I take no responsibility for this, you should have a backup and if you make a mistake during this process you could wipe out all of your data. So backup somewhere else before starting this as a precaution, or make sure it's data you could afford to lose. The RAID 1 Setup (Hardware Wise) I've already setup my 2 x 1TB (Seagate) drives with identical partitions, make sure your new hard drive (the empty one) is setup like your curr........