Nov 15 17:00:49 rttbox kernel: overlayfs: filesystem on '/var/lib/docker/overlay2/check-overlayfs-support450709549/upper' not supported as upperdir Nov 15 17:00:49 rttbox dockerd[93755]: failed to start daemon: error initializing graphdriver: driver not supported The above error is often/normally caused because you are trying to run docker out of an unsuitable directory/filesystem. For example if you try to place docker's data inside an existing overl........

Enable "cli" mode equivalent in JunOS cli Configure Mode configure So rather than going to the console on a Cisco switch and typing "enable" and then "conf t", the equivalent in JunOS is "cli" and "configure". How Do You Apply Changes You've Made? You can make all kinds of changes to the switch, but remember they are not........

The easiest way to know if your videos are playing with GPU acceleration are to watch the process of xplayer, mpv or whatever you are playing. The CPU usage should be no more than 10% for that process/program if it is using acceleration. Let's manually play with vdpau to make sure it works before we make it permanent: First make sure you have libvdpau installed: sudo apt install vdpau-driver-all If yo........

Install Errors on Version 12: This error happened on QEMU emulator version 2.11.1 pve-qemu-kvm_2.11.1-5 on Proxmox/Debian but installing on QEMU.12 on Centos 6 did not produce the error. *Update it is not related to the OS or QEMU version. This happened in Centos 6 too after a second install. What really causes this even though you successfully install........

The strange thing is that usually the first install or two will work on any new machine but then it suddenly won't. I had this experience on QEMU 2.13 on a different machine. There is something finicky or buggy about the CUCM installer even when choosing the same virtual hardware specs. qemu-kvm command: /usr/libexec/qemu-kvm -version QEMU PC emulator version 0.12.1 (qemu-kvm-0.12.1.2-2.506.el6_10.1), Copyright (c) 2003-2008 Fabrice Bellard ........

This works on the 2000 and 3000 series generally. *The easy way is to just hold the mode button for 10+ seconds. The full/proper way is below: 1.) Either power on the unit and hold the "mode" button or hold the "mode" button until you see the below: 00:04:08: %SYS-7-NV_BLOCK_INIT: Initalized the geometry of nvram 00:04:08: %EXPRESS_SETUP-6-CONFIG_IS_RESET: The configur........

Error: Unable to apply new quota values: quota not running Container start failed (try to check kernel messages, e.g. "dmesg | tail") Killing container ... Container was stopped Error: Unable to apply new quota values: quota not running Can't umount /vz/private/123123: Invalid argument [root@rtt 123123]# vzquota on 123123 vzquota : (error) Can't open quota file for id 123123, maybe you need to reinit........

I believe from what I've read that this card's driver doesn't support the features after trying all known troubleshooting methods. ffmpeg -i uservideoRendered.mp4 -filter:v hwupload_cuda,scale_npp=w=1920:h=1080:format=nv12:interp_algo=lanczos,hwdownload -c:v hevc_nvenc -profile main -preset slow -rc vbr_hq -c:a copy uservideoRendered.mp4-test ffmpeg -i uservideoRendered.mp4 -filter:v hwupload_cuda,scale_npp=w=1920:h=1080:format=nv12:interp_algo=lanczos,hwdownload........

The solution is simple but strange, if you copy your /var/lib/mysql directory to another server and think it will work, be sure to check if you have /var/log/mysql and binary log files. If you do, the server will not work and will give you errors like below and crash without the proper log files. UPDATE user SET password=password("newpass") WHERE user='root'; flush privileges; ERROR 2013 (HY000): Lost connection to MySQL server durin........

migrating from an old OpenVZ (Centos 5) to new OpenVZ (Centos 6) Also if migrating from 32-bit HN to 64-bit your RAM will probably be much bigger than it should be! 16x bigger eg. 32bit HN: total used free shared buffers cached Mem:&nb........

drbd 8.3 hard drive failure recovery drbdadm attach r0 DRBD module version: 8.3.10 userland version: 8.3.8 you should upgrade your drbd tools! 0: Failure: (119) No valid meta-data signature found. ==> Use 'drbdadm create-md res' to initialize meta-data area. ........

Starting container... vzquota : (error) Quota on syscall for id 42131: No such file or directory vzquota on failed [3] Solution cd /var/vzquota mv quota.42131 quota.42131-disable vzctl start 42131 Starting container... Initializing quota ... Container is mounted Adding IP address(es): Setting CPU units: 1000 Container start in progress... ........

Starting online migration of CT 25000 to 192.168.5.1 Preparing remote node Initializing remote quota Syncing private Live migrating container... Error: Failed to suspend container CPT ERR: f68cf000,25000 :foreign process 15755/14731(vzctl) inside CT (e.g. vzctl enter or vzctl exec). CPT ERR: f68cf000,25000 :suspend is impossible now. CPT ERR: f68cf000,25000 :foreign process 15755/14731(vzctl) inside CT (e.g. vzctl enter or........

This assumes that you've at least created the correct partition for your DRBD already. Notice that I am "diskless", that's because either your DRBD partition doesn't exist/has been renamed (eg. sdb becomes sda when sdb dies and you reboot) or because that drive is really actually dead/gone. *If you need to permanently change the partition/device for your resource be sure to edit /etc/drbd.conf on both hosts and reload the config. (replace r0 with........

I've only used it on Centos, soI thought I'd make a quick Debian guide: Install the DRBD Package apt-get install drbd8-utils Reading package lists... Done Building dependency tree Reading state information... Done The following packages were automatically installed and are no longer required: libswfdec-0.8-0 Use 'apt-get autoremove' to remove them. The following........

Initializing quota ... Error: Not enough parameters, diskinodes quota not set vzctl set $veid --diskinodes 90000:91000 --save New versions of OpenVZ seem to have some strange diskinodes parameter which is required.........

This has stumped me a few times because I keep forgetting that Centos 5.5 comes with a default iptables configuration that ends up blocking DRBD traffic,I tried all the normal things and couldn't understand why I couldn't make my normal DRBD config work. So if you have WFConnection problems and have tried the normal "mailing list" fixes, check your firewall status first! Both Nodes Say the Following: version: 8.3.8 (api:88/prot........