• How to access a disk with bad superblock Linux Ubuntu Debian Redhat CentOS ext3 ext4


    Have you ever tried mounting a partition that you exists but you get this error? mount: /mnt: can't read superblock on /dev/sda1. The superblock in this example was bad because the physical disk had corruption and bad blocks/sectors. However, the data was generally accessible and you can always try this trick below (with caution and no warranty). This is specifically for filesystems that place superblocks in multiple locations, which........
  • vmkping -I vmk1 10.0.2.69 PING 10.0.2.69 (10.0.2.69): 56 data bytes sendto() failed (Host is down)


    [root@localhost:~] vmkping -I vmk1 10.0.2.69 PING 10.0.2.69 (10.0.2.69): 56 data bytes sendto() failed (Host is down) vsphere distributed switch vmotion not working [root@localhost:~] esxcfg-route -l VMkernel Routes: Network Netmask Gateway Interface&........
  • VMWare ESXi 6.7 SSH/PowerShell CLI Commands


    [root@localhost:~] BootModuleConfig.sh echo host-ind nfcd........
  • Centos 6 how to guide convert LVM non-RAID into mdadm 1/10 RAID array live without reinstalling


    Here is the scenario you or a client have a remote machine that was installed as a standard/default minimal Centos 6.x machine on a single disk with LVM for whatever reason. Often many people do not know how to install it to a RAID array so it is common to have this problem and why reinstall if you don't need to? In some cases on a remote system you can't easily reinstall without physical or KVM access. So in this case you add a second physical or disk or already ha........
  • Convert HDD/Hard Drive Partition(s) into non-RAID into RAID 1 using existing data without data loss and without reformatting.


    Before we start I take no responsibility for this, you should have a backup and if you make a mistake during this process you could wipe out all of your data. So backup somewhere else before starting this as a precaution, or make sure it's data you could afford to lose. The RAID 1 Setup (Hardware Wise) I've already setup my 2 x 1TB (Seagate) drives with identical partitions, make sure your new hard drive (the empty one) is setup like your curr........
  • Linux EXT3 16GB-17GB maximum filesize issue solved/how to fix


    I have no idea why but mkfs.ext3 defaults to a patheticlly small blocksize of 1024 bytes/1KB (kilobyte). That means the maximum filesize is ONLY 16GB! With 2KB/2048 bytes you get a 256 GB maximum filesize, and with 4KB/4096 bytes you get 2TB! I finally noticed/paid attention to this after realizing that with rsync and scp that no file larger than 17GB could be transferred. I then realized it must be a file size limit on the partition. Here is what tune2fs tol........
  • Latest Articles

  • Apache PHP sending expires header solution cannot use cache with CDN
  • How to install virt-manager in Mint 22/Ubuntu 22
  • Infiniband Guide
  • python mysql install error: /bin/sh: 1: mysql_config: not found /bin/sh: 1: mariadb_config: not found /bin/sh: 1: mysql_config: not found mysql_config --version
  • FreePBX 17 How To Add a Trunk
  • Docker Container Onboot Policy - How to make sure a container is always running
  • FreePBX 17 How To Add Phones / Extensions and Register
  • Warning: The driver descriptor says the physical block size is 2048 bytes, but Linux says it is 512 bytes. solution
  • Cisco How To Use a Third Party SIP Phone (eg. Avaya, 3CX)
  • Cisco Unified Communication Manager (CUCM) - How To Add Phones
  • pptp / pptpd not working in DD-WRT iptables / router
  • systemd-journald high memory usage solution
  • How to Install FreePBX 17 in Linux Debian Ubuntu Mint Guide
  • How To Install Cisco's CUCM (Cisco Unified Communication Manager) 12 Guide
  • Linux Ubuntu Redhat How To Extract Images from PDF
  • Linux and Windows Dual Boot Issue NIC Won't work After Booting Windows
  • Cisco CME How To Enable ACD hunt groups
  • How to install gns3 on Linux Ubuntu Mint
  • How to convert audio for Asterisk .wav format
  • Using Cisco CME Router with Asterisk as a dial-peer