You may have been expecting a normal sized kernel but if you don't disable these .config options you may have a kernel that is several gigabytes. CONFIG_SLUB_DEBUG=no CONFIG_DEBUG_INFO=no CONFIG_DEBUG_MISC=no Rebuild and you should find that the kernel is the normal and as expected size.........

This seems to have changed for RHEL 8 where a normal dracut to update your initramfs creates a system that only boots for the running kernel. For example if you have Kernel 5 and then chroot into a RHEL 8 variant which uses kernel 4.18, and run dracut, it seems that by default the system will be unbootable. It is also the case that if you move your RAID array or drives to another server that it will be unbootable, because dracut seems to only include modules needed for the curre........

The easiest way for the current running kernel is: update-initramfs -u -k `uname -r` You could change -k to a specific kernel name if for some reason the current is not running (eg. if you are chrooted or in recovery mode). If you want to update all kernels then use "-k all" update-initramfs -k all -u update-initramfs: Generating /boot/initrd.img-5.4.0-162-generic........

In Thunderbird in a very large folder suddenly all of my e-mail list became blank/white even though you could click on the invisible/white/blank lines and it would show the e-mails. Itried to close and reopen but only going to Folder -> Properties and clicking Repair Folder fixed it (basically it had to redownload/rebuild the entire index and all e-mails).........

Iam not sure why this is happening neither the hostnode or VM changed. All I did was reboot the hostnode and startup the Centos VM again, also note it happened with the original kernel on the VM and also the latest 6.9 kernel as of this writing as shown below. Host Node: Centos 6.9 Kernel:2.6.32-696.6.3.el6.x86_64 Kernel: 2.6.32-042stab123.9 Same result in any kernel above........

grub> root (hd0,0) root (hd0,0) Filesystem type is ext2fs, partition type 0xfd grub> setup (hd0) setup (hd0) But if you do: root (hd1,0) setup (hd1) it does work, I think hd0/sda had a GPT partition that was not removed properly (what I did was just dd bs=512 count=1 the partition table from another drive since the partition table should be identical). Checking if "/boot/grub/........

In plain English this happens after you upgrade VBOX and it rebuilds kernel modules based on a newer kernel than you are running (eg. you upgraded your kernel but haven't booted into it). It is too bad there is not a standard work around that would allow it to realize this and keep old kernel modules and use them if it detects your current kernel is older than the most recently build modules. =============== RTR3InitEx failed with rc=-1912 (rc=-1912) The........

In this example we have 2 drives in a RAID array and /dev/sdb is the one that failed. /dev/sda1 is also the /boot partition which we tell grub to install on /dev/sdb eg install root (hd0,0) /dev/sda1 on the new drive /dev/sdb (hd1) First copy the partition table from /dev/sda to /dev/sdb dd if=/dev/sda of=/dev/sdb bs=512 count=1 Run partprobe to detect the new partition table partprobe........

Error: Unable to restore run data (10) Error: Unable to restore run data (11) Ikeep getting this error but so far there is no obvious solution. Sometimes I've had to remove the *.hist files so I'll try that again. *Update This is an ongoing random problem after months of running webalizer it runs into some problem that can only be fixed by removing the following files so it can rebuild the stats (you end up losing p........

root@hkhosting [/]# service httpd start Starting httpd: Syntax error on line 2 of /etc/httpd/conf/httpd.conf: Invalid command 'Alias', perhaps misspelled or defined by a module not included in the server configuration ........

The units in echo are kB as in kilobyte. Setting a high sync speed echo 120000 >/proc/sys/dev/raid/speed_limit_min This will increase the speed, note that sometimes a rebuild is slow due to current disk activity/iowait. If that is not the cause then you may have a hardware issue (controller, cable or a bad drive). Setting a lower sync speed echo 1200 >/proc/sys/dev/raid/speed_limit_max........

Have you ever unplugged the wrong drive and then had to rebuild the entire array? It may not be a big deal in some ways but it does make your system vulnerable until the rebuild is done. Many distros often enable the "bitmap" feature and this basically keeps track of what parts need to be resynced in the case of a temporary removal of a drive from the array, this way it only needs to sync what has changed. To enable bitmap to speed up rebuilds and sync........

This array is a RAID 1 and in this case 1 of the 2 drives failed (a WD drive and I've found them to be the weakest and most unreliable of any brand and are easily damaged/DOA when shipping them). mdadm --manage /dev/md0 --add /dev/sdb1 The above assumes the array you want to add to is /dev/md0 and the device we are adding is /dev/sdb1 *One thing to remember is to make sure the partition you are adding is the correct size for the array. You can also g........

I experienced this with CPanel's Exim after an auto-update (a Google of this error produces lots of complaints with few clear solutions). In this case I'll put the solution at the top. Run /scripts/buildeximconf to rebuild the Exim config and it should be fine after that. mail -vs "from test" user@dest.com < .bash_history LOG: MAIN cwd=/root 4 args: send-mail -i -v user@dest.com LOG: MAIN &........

I dread updating the kernel and rebooting to find the Ubuntu graphics aren't working and you have to manually intervene. This is usually because Ubuntu for whatever reason didn't update the drivers you need (eg. the manually compiled Nvidia Kernel driver that MUST be recompiled for each and every kernel update unfortunately). The most common reason may be that "linux-source" hasn't been installed automatically on my system. I tried to manually reinstall the........

It's weird because I have a nearly identical box and setup and I can update the ovzkernel-PAE* just fine but on this box it doesn't work. I only get this error with the openvz.repo and not others such as Centos-Base.repo With my other server it works normally: ================ Setting up Update Process Resolving Dependencies --> Running transaction check ---> Package ovzkernel-PAE.i686 0:2.6.18-238.12.1.el5.0........

This made me nervous but it's clearly a cronjob based on the messages log that happens every Sunday at about 4:22. I actually can't find any evidence of it in cron.d cron.daily but it is there somewhere obviously. What I don't get is why doesn't this cronjob do a datacheck like Ubuntu's cronscript does? When you unnecessarily rebuild the array you lose your redundancy during that point which makes your data extremely vulnerable. *Update I did a grep of &q........

This doesn't seem to be widely known (maybe it's in some documentation that none of us read though)but there's an easy way to check the integrity of any mdadm array: sudo echo check > /sys/block/md0/md/sync_action -bash: /sys/block/md0/md/sync_action: Permission denied sudo will never work, this only works as root since echo is not actually a binary/command. It is built-into bash. /sys/devices/virtu........

I separated the 2 drives in the RAID 1 array. 1 is the old one /dev/sda and is out of date, while the separated other one /dev/sdc was in another drive and mounted and used with more data (updated). I wonder how mdadm will handle this: usb-storage: device scan complete md: md127 stopped. md: bind md: md127: raid array is not clean -- starting background reconstruction raid1: raid set md127 active with 1 out of 2 m........

md: Autodetecting RAID arrays. md: autorun ... md: considering sdb1 ... md: adding sdb1 ... md: adding sda1 ... md: created md0 md: bind md: bind md: running: md: kicking non-fresh sda1 from array! md: unbind md: export_rdev(sda1) raid1: raid set md0 active with 1 out of 2 mirrors The md0 raid kicked sda1 ou........

http://www.tomshardware.com/news/RAID-5-Doomed-2009,6525.html I found this article interesting, it basically says that with 2TB hard drives or larger sizes, you are more likely to encounter an unrecoverable read error. But is this just another Y2K doomsday? Don't HDD's have enough advanced hardware ECC error and read recovery to prevent this from happening? I'm almost tempted to build a 3 x........

PHP cannot access /usr/bin/opensslI have verified the username that runs the process is able to access /usr/bin/openssl and it does exist but the PHP script is saying it doesn't exist: [code:1:1fd0f3abbe] if (!file_exists($OPENSSL)) { //echo "ERROR: OPENSSL $OPENSSL not foundn"; }[/code:1:1fd0f3abbe] I don't get itI can clearly see the contents of /usr/bin by using the PHP system fu........

Time for new RAM!Has anyone seen RAM is damn cheap now? My PC is like 5 years old so it's time to rebuild!........

Loaded plugins: fastestmirror rpmdb: mmap: No such device error: db4 error(19) from dbenv->open: No such device error: cannot open Packages index using db3 - No such device (19) error: cannot open Packages database in /var/lib/rpm Traceback (most recent call last): File "/usr/bin/yum", line 29, in ? yummain.user_main(sys.argv[1:], exit_code=True) File "/usr/share/yum-cli/yummain.py&qu........