• redis requirements


    sysctl vm.overcommit_memory=1 echo never > /sys/kernel/mm/transparent_hugepage/enabled echo 511 > /proc/sys/net/core/somaxconn 1:M 26 Nov 2023 21:34:33.840 # WARNING: The TCP backlog setting of 511 cannot be enforced because /proc/sys/net/core/somaxconn is set to the lower value of 128. 1:M 26 Nov 2023 21:34:33.840 # Server initialized 1:M 26 Nov 2023 21:34:33.840 # WARNING overcommit_memory is set to 0! Background sa........
  • Mint Ubuntu Linux Gnome Showing Home Directory on Desktop instead of Desktop Directory


    During a migration or other custom setup, it's possible you don't have a $HOME/Desktop and as a result the config file that controls this is set to just use your $HOME directory. This is controlled in the file: $HOME/.config/user-dirs.dirs As we can see below, Desktop, Downloads, Music and Pictures are set to $HOME. We can edit any of these as we like. # This file is written by xdg-user-dirs-update # If you want........
  • bind / named how to make a wildcard record and retain defined A records


    It is almost as intuitive as we would like it is just a *. So literally: *INA 127.0.0.1 Complete working bind zonefile below: $TTL 86400 @ IN SOA ns.rtt.ca. ns2.rtt.ca. ( 1247605715; Serial &n........
  • Linux How To Clone One System Harddrive to another remote system


    The easiest way is to use SSHand DD or a combination of netcat. SSHwill be a little slower due to encryption but is the most secure way (on two older systems the average clone speed is about 40-50MB/s). This is also OS independent as it doesn't matter what the source OS is because you are literallly cloning the drive so you retain the partition table and settings. Clone HDD using SSH and DD........
  • Ubuntu/Debian/Linux won't boot and drops to Busybox shell after cloning HDD with dd


    I don't recall having this issue in the distant past but nowadays at least Debian seems to be very picky about this. I used dd to copy one hard drive to another and tried booting it. Everything seemed fine with grub working but each time it would drop to the busybox shell. There is no particular error so this is misleading. Normally the first things you would check are to make sure your fstab is correct (that the UUID is correct)and that you've updated grub.&........
  • The Best NoSQL Solution


    To first start off, there are many misconceptions about NoSQL and especially its strengths and weaknesses. Even the popular NoSQL solution MongoDB is fraught with issues that no one seems to be concerned about aside from a few but there are serious issues with database integrity and verified writes. MySQL was considered dangerous or incomplete at one point without having the transactional safety features of Oracle for example. However the NoSQLimplementations seem........
  • WARNING: REMOTE HOST IDENTIFICATION HAS CHANGED!


    The easiest way is if you have a secure way to connect and verify the hostkey of the remote host by using this guide. @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@ @ WARNING: REMOTE HOST IDENTIFICATION HAS CHANGED! @ @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@ IT IS POSSIBLE THAT SOMEONE IS DOING SOME........
  • rsync ERROR: sdb2/backup.r18 failed verification -- update retained.


    ERROR: sdb2/backup.r18 failed verification -- update retained. This happened when Iwas rsyncing a dying hard drive, a lot of people seem to report this as an error with rsync itself but I don't think rsync is the issue at all. I know the source hard drive was bad, it was having all kinds of timeout, seek, hardware ECC recovered and reset errors. The only time something else could be the problem is if the data is being corrupted in transit, perhaps through........
  • Clone any OS partition perfectly


    Clone any OS partition perfectlyIn one box I needed to copy the boot partition to another disk while retaining the MBR and other data. I simply ran this command: [code:1:1b1ff110ca]dd if=/dev/hda1 of=/dev/hdb1[/code:1:1b1ff110ca] [b:1b1ff110ca]if[/b:1b1ff110ca] = source patition [b:1b1ff110ca]of[/b:1b1ff110ca] = destination partition Here's an interesting article on it http://www.rajeevnet.com/hacks_hints/os_cl........
  • Latest Articles

  • FreePBX 17 How To Add a Trunk
  • Docker Container Onboot Policy - How to make sure a container is always running
  • FreePBX 17 How To Add Phones / Extensions and Register
  • Warning: The driver descriptor says the physical block size is 2048 bytes, but Linux says it is 512 bytes. solution
  • Cisco How To Use a Third Party SIP Phone (eg. Avaya, 3CX)
  • Cisco Unified Communication Manager (CUCM) - How To Add Phones
  • pptp / pptpd not working in DD-WRT iptables / router
  • systemd-journald high memory usage solution
  • How to Install FreePBX 17 in Linux Debian Ubuntu Mint Guide
  • How To Install Cisco's CUCM (Cisco Unified Communication Manager) 12 Guide
  • Linux Ubuntu Redhat How To Extract Images from PDF
  • Linux and Windows Dual Boot Issue NIC Won't work After Booting Windows
  • Cisco CME How To Enable ACD hunt groups
  • How to install gns3 on Linux Ubuntu Mint
  • How to convert audio for Asterisk .wav format
  • Using Cisco CME Router with Asterisk as a dial-peer
  • Cisco CME How To Configure SIP Trunk VOIP
  • Virtualbox host Only Network Error Failed to save host network interface parameter - Cannot change gateway IP of host only network
  • Cisco CME and C7200 Router Testing and Learning Environment on Ubuntu 20+ Setup Tutorial Guide
  • Abusive IP ranges blacklist