• How To Do Linux Network Bonding Teaming in Mint Debian Ubuntu


    Bonding is an excellent way to get both increased redundancy and throughput. It is similar to the "Network Teaming" feature in Windows. There are a few different modes but we will use mode 6, I think it's the best of both worlds, as it is not just a failover, but it provides round robin, so you will get redundancy and load balancing. So if you have a 1G single port, you will have a combined throughput of 4G at this point. Just bear in mind that the true thr........
  • Cisco Howto Configure Console Port/Terminal/Comm Server with Async Cable Setup


    This assumes that you've already installed the relevant HWIC cards eg. Cisco Asynchronous Serial NIM These are essentially cards that you install into your router, once installed you connect an Async cable to one of the ports on the card which normally gives you 8 console cables and are normally labelled 1 through 8. You connect all of the cables to the devices you need (even non-Cisco devices) whether switches, routers or firewalls, they will usually work. The real m........
  • wodim / cdrecord error cannot burn DVD or BDR .iso Errno: 5 (Input/output error), write_g1 scsi sendcmd: no error


    dvd+rw-mediainfo /dev/sr0 INQUIRY: [ASUS ][BW-16D1HT ][3.00] GET [CURRENT] CONFIGURATION: Mounted Media: 11h, DVD-R Sequential Media ID: RITEKF1&n........
  • VMWare 6.7 VCSA VSphere ESXi Management SSO Install Guide on Linux using the CLI


    #mount the VCSA DVD mount /dev/sr0 /mnt/cd #alternatively you could mount the iso directly mount -o loop vcsa.iso /your/mount/path #for this purpose we are using the CLI installer on Linux cd /mnt/cd/vcsa-cli-installer/lin64 #no it's not going to be that easy you can't just run vcsa-deploy like that you need to use a template or configured .json file ./vcsa-deploy Usage: vcsa-deploy [-h] [--version] [--supported-deploymen........
  • Track 01: 34 of 1726 MB written (fifo 100%) [buf 99%] 3.6x.Errno: 5 (Input/output error), write_g1 scsi sendcmd: cmd timeout after 1.897 (40) s CDB: 2A 00 00 00 44 A9 00 00 1F 00 resid: 6144 cmd finished after 1.897s timeout 40s write track da


    These errors believe it or not are simply because of not being the root user or running with sudo! However if you didn't know to try as root you'd think there was a problem with your burner or disc Essentially it looks like without root you cannot send the required scsi commands to continue writing. Ithink cdrecord should have built-in tests or safeguards to see if it has the permissions to run the required commands. I guess for more advanced users the idea is simila........
  • ADATA SU800 256GB 3D NAND Flash SSD Test & Review


    I keep reading these drives are slower, but they are cheap and still SSDand work very fast for my needs. As you can see the sequential read is 481-491MB/s, if I put them in MDADM RAID10 mode (normal RAID1) they should give me well over 900MB/s and with redundancy and being very cheap for what they offer. [1232206.315622] scsi 8:0:1:0: Direct-Access ATA ADATA SU800&........
  • PAP2T Linksys VOIP strange ring problem


    The problem is that the default of most of these units is set for non-North American phones so the ring sounds like it cuts off and is not sequential. How To Fix the Issue Click on "Regional" and make sure you are in Advanced mode. ........
  • Unixbench Testing


    The first is a dual CPU AMD Opteron 2373EE (4 cores x 2) and I think it did bad because it has some old 250GB SATAs which can only do about 65MB/s max sequential reads. I think it should have blown away the second (AMD X4 640 Quad Core). [root@fs12home unixbench-4.1.0-wht-2]# ./Run make all make[1]: Entering directory `/root/unixbench-4.1.0-wht-2' Checking distribution of files ./pgms exists ./src exists........
  • RAID 1 and Non-RAID Hard Drive Performance Comparison using tiobench


    Here is a RAID 1 partition (500GB Seagate & 2TB WD): Sequential Reads File Blk Num Avg Maximum Lat%&nbs........
  • Latest Articles

  • How To Stop DNSMasq from listening on all IPs/Interfaces and allow only localhost
  • du - VAS Billing Subscriptions Hack/Scam MLPremiumSub Invascom Astromart Issues Complaint
  • Docker Swarm vs Kubernetes Comparison Guide
  • When is it time to leave your VPS/VDS Cloud Hosting Provider?
  • 2024 Buyer's Guide: How to Choose and Buy the Best VPS/VDS for Your Needs - Tips and Strategies
  • Postfix / sendmail config for DKIM, SPF and DMARC Tutorial Guide E-mail Delivery for Hotmail.com Gmail.com and More HowTo
  • Install Grafana on Linux Debian Ubuntu Tutorial Guide
  • How To Completely Disable ufw in Linux Ubuntu Mint Debian
  • System has not been booted with systemd as init system (PID 1). Can't operate. Failed to talk to init daemon. Ubuntu Debian Linux Solution Cannot reboot
  • Mint Ubuntu Linux Gnome Showing Home Directory on Desktop instead of Desktop Directory
  • vi vim not doing code highlighting E319: Sorry, the command is not available in this version solution
  • Proxmox How To Rename Node Hostname Fix Solution
  • Linux how to get list of all timezones on system Ubuntu
  • Proxmox install issue cannot see the buttons or install wrong / bad resolution cannot see the entire screen problem solution
  • configure.ac:75: error: possibly undefined macro: AC_PROG_LIBTOOL If this token and others are legitimate, please use m4_pattern_allow. See the Autoconf documentation. solution
  • Can't exec "aclocal": No such file or directory at /usr/share/autoconf/Autom4te/FileUtils.pm line 326. autoreconf: failed to run aclocal: No such file or directory solution
  • /bin/sh: autoreconf: command not found solution
  • glib-2.0 required to compile QEMU solution
  • How To Upgrade Debian 8,9,10 to Debian 12 Bookworm
  • Linux dhcp dhclient Mint Redhat Ubuntu Debian How To Use Local Domain DNS Server Instead of ISPs