Since newer versions of Ubuntu like 20, you will find there is no longer dynagen and that the dynamips provided is faulty and will segfault each time: Cisco Router Simulation Platform (version 0.2.14-amd64/Linux stable) Copyright (c) 2005-2011 Christophe Fillot. Build date: Apr 3 2018 12:20:29 Local UUID: 3c1c0b7f-2fab-4fda-b40b-74841d1bcfe0 Instance ID set to 1. netio_tap_create: unable to open TAP device tap1 (No such fi........

It is a bit different and annoying here for these types of routers/models as you need to physically remove the CF (Compact Flash) and only then, will it enter ROMMON mode (Ctrl + Pause remotely over the console will not do it for us). This means you cannot do this remotely, or at least not without the help of a remote/physical helper. Step 1.) Power off, router and remove CF Disk Slot#2 Go to the router and remove the slot#2 cover uses your hand or it may help to use a........

Intel NUC J3455 vs Vorke V1 J3160 Both are excellent units but the J3160 is nicer if you require even lower power usage (6W vs the Intel 10W). The price is attractive on the Vorke V1 as well. It's been said that the Intel J3455 NUC has a buggy BIOS and some other issues that require attention. The Intel J3455 is still nice because it has 2 RAMslots but it does get hotter due to lack of fan. The Vorke V1 runs cooler, uses less power an........

I keep reading these drives are slower, but they are cheap and still SSDand work very fast for my needs. As you can see the sequential read is 481-491MB/s, if I put them in MDADM RAID10 mode (normal RAID1) they should give me well over 900MB/s and with redundancy and being very cheap for what they offer. [1232206.315622] scsi 8:0:1:0: Direct-Access ATA ADATA SU800&........

At first my BIOS said the card may not work right because there is no more option ROM space. I disabled the Option ROM for both LSI 1068 and 2008 chipsets, Network Boot ROM and most other PCI slots, Serial Port, etc... and the message went away but the card still does not work properly. But it still cannot initialize the card properly(does not work): [ 33.943272] NVRM: This PCI I/O region assigned to your NVIDIA device is invalid:........

Motherboard: Gigabyte GA-3CESL: http://b2b.gigabyte.com/products/product-page.aspx?pid=2658#dl Dell Part Numbers for the motherboard: R1232 R1232L R2232S SERVER MOTHERBOARD GENUINE 408P9 CN-0408P9 GA-3CESL Manual Download here RAMSlots: 16 (8 controlled by each CPU) RAMType: DDR2 ECC 5300P........

Dell CS24-NV7 Unusually the Virtualization was enabled when I got this server but all the NICs were diabled in the BIOS including PXE boot! Advanced -> Advanced Chipset Control PCI Slot 1 Option ROM: Enabled Onboard LAN1 Control: Enabled LAN1 Option ROM Scan: Enabled (you need it for PXE boot) Onboard LAN2 Control: Enabled LAN2 Option ROM Scan: Enabled *you will need to reboot and........

I've got one of these for testing projects from work at home and got more than I bargained for with the time I've spent on it due to the storage handing/Perc 6/i cards. My particular model came with the following: 2U Rack Mount Server with Rails 2xOpteron 2373 EE (Quad Core, there is a 6-core version that can be found at times) 16GB RAM 2 x 250GB Seagate SATA 2 x Dell Perc 6/i (horrible and a nightmare to work........

The results are not bad, the Hitachi performs the same as it does in a SATA2 motherboard. However, the 2TB is much different, on a similar 2TB Toshiba I get about 198MB/s on a different motherboard vs the 2TB Hitachi which should produce similar results. This Dell Perc 6/i is on a PCI x8 riser card and is connected to a 12-port backplane. Adapter #0 Enclosure Device ID: 32 Slot Number: 0 Enclosure position: N/A De........

LSi Megaraid At first it was configured as a RAID 0, then I deleted the Virtual Disk Group. I thought both drives would be shown and detected in Linux as sda and sdb but it actually shows nothing. To make them work you have to hit Ctrl+R before the system boots (when prompted) and create a Virtual Disk Group. In my case I created each one as RAID 0 (with a single drive only) as I just wanted JBOD but there is no such option or default in these Dell Pe........

mod_status is a great way to track down the source of high CPU usage and to find what vhost/script is the cause of it. It gives you a live view of bandwith usage, CPU usage, and memory usage broken down by domain/vhost and script/URI. Enable mod_status vi /etc/httpd/conf/httpd.conf ExtendedStatus On SetHandler server-status Order Deny,Allow Deny from all All........

I keep getting this in my SSH/Bash console: NotifyByPopup::slotDBusNotificationClosed: 465 -> 0  ........

This is obviously a bug in the r8169 kernel module and it seems to affect a lot of people. I upgraded to the latest kernel and hope this won't happen anymore, as it is a very serious error. This is especially serious for those who are running servers with this chipset, who can afford for the NIC to randomly go off-line for no apparent reason? [655548.189113] type=1505 audit(1277067560.902:5): operation="profile_load" name="/usr/bin/freshclam&q........

As much of a computer nerd as Iam, I'm usually a late adopter to technology for a few reasons. Ifeel most new hyped technologies and electronics are mainly fads, and I'm also cheap. Adopting later means you avoid the bugs, kinks and most importantly pay the lowest price, that's me being cheap again :) I never read much about the iPhone but Isaw all the hype around it and until recently I wasn't a big fan of anything Apple until a few years ago I realize........

When trying to even cd or ls the mounted OCFS2 partition it crashes. Ithink this is a combination of VMWare Server's problem and the way I mounted and symlinked to it. More than anything this shows the problem and lack of forsight with VMWare, but also that OCFS2 is easily crashed if you do strange things. Output of /var/log/messages for OCFS2 Apr 10 15:57:45 localhost kernel: [84331.691258] Modules linked in: vmnet vmci vmmon ocfs2_stac........

There's a lot of information and guides on OCFS2 for RHELand Centos Linux but the package setup and configuration is slightly different and this has thrown some people off. Installing OC2FS You should install the following packages to get started: apt-get install ocfs2-tools ocfs2console Configure OC2FS In RHEL/Centos the main configuration file is located in /etc/sysconfig/o2cb However in Debian based Linux it is located........