/ - rtt - IT Resource

  • HP DL385 G7 Linux BIOS Update Flash


    wget https://downloads.linux.hpe.com/repo/spp/rhel/6/x86_64/current/CP017004.scexe --2018-08-16 05:11:16--  https://downloads.linux.hpe.com/repo/spp/rhel/6/x86_64/current/CP017004.scexe Resolving downloads.linux.hpe.com (downloads.linux.hpe.com)... 15.249.152.85 Connecting to downloads.linux.hpe.com (downloads.linux.hpe.com)|15.249.152.85|:443... connected. HTTP request sent, awaiting response... 200 OK Length: 1525561 (1.5........
  • OVF Tool: Error: Task failed on server: This host does not support Intel VT-x. VMWare VCenter install On ESXi ERror


    Intel VT-X is enabled in Virtualbox but it doesn't seem to pass through the needed vmx extension despite the following variables on the host confirming it is enabled: cat /sys/module/kvm_intel/parameters/nested Y cat /sys/module/kvm_intel/parameters/ept Y     OVF Tool: Disk progress: 99% OVF Tool: Transfer Completed OVF Tool: Powering on VM: Embedded-vCenter-Server-Appliance- OVF Tool: Task p........
  • VMWare 6.7 VCSA VSphere ESXi Management SSO Install Guide on Linux using the CLI


    #mount the VCSA DVD mount /dev/sr0 /mnt/cd #alternatively you could mount the iso directly mount -o loop vcsa.iso /your/mount/path #for this purpose we are using the CLI installer on Linux cd /mnt/cd/vcsa-cli-installer/lin64 #no it's not going to be that easy you can't just run vcsa-deploy like that you need to use a template or configured .json file ./vcsa-deploy Usage: vcsa-deploy [-h] [--version] [--supported-deploymen........
  • OpenVPN cannot ping remote IP routing loop issue after connecting


    Sometimes if you have a very basic configuration OpenVPN on the client side for some reason sends all traffic to the OpenVPN server IP through the tun0 which is of course impossible and creates a block or routing loop.  This is because you need to use your normal ISP/LAN gateway to hit the OpenVPN server if it is remote/offsite as is usually the case.  So if you are connected to the OpenVPN through say a tun0 device and your routing is set to connect to the OpenVPN&nbs........
  • ERROR 2013 (HY000): Lost connection to MySQL server during query


    The solution is simple but strange, if you copy your /var/lib/mysql directory to another server and think it will work, be sure to check if you have /var/log/mysql and binary log files.  If you do, the server will not work and will give you errors like below and crash without the proper log files. UPDATE user SET password=password("newpass") WHERE user='root'; flush privileges; ERROR 2013 (HY000): Lost connection to MySQL server durin........
  • MySQLD Server shutdown remotely unexpectedly


    170110  5:35:23 [Note] /usr/libexec/mysqld: Normal shutdown 170110  5:35:23 [Note] Event Scheduler: Purging the queue. 0 events 170110  5:35:23  InnoDB: Starting shutdown... 170110  5:35:24  InnoDB: Shutdown completed; log sequence number 0 12765401 170110  5:35:24 [Note] /usr/libexec/mysqld: Shutdown complete 170110 05:35:24 mysqld_safe mysqld from pid file /var/run/mysqld/mysqld.pid ended........
  • remove gpt partition linux


    sudo fdisk /dev/sdh WARNING: GPT (GUID Partition Table) detected on '/dev/sdh'! The util fdisk doesn't support GPT. Use GNU Parted. WARNING: The size of this disk is 8.0 TB (8001563221504 bytes). DOS partition table format can not be used on drives for volumes larger than (2199023255040 bytes) for 512-byte sectors. Use parted(1) and GUID partition table format (GPT). The device presents a l........
  • Virtualbox errors on Ubuntu/Debian/Mint


      The solution was to reinstall the vbox dkms package and do a manual modprobe of the modules it makes. I never sorted out the unable to start due to the USB issue, I did have the guest additions installed but the only way to boot was to change the pointing device from USB to PS2 and then to disable the USB controller (if your pointing device is set as USB, disabling USB will not work because it will re-enable by default when it sees your pointing device is USB, this is w........
  • Dell Perci 6/i Firmware Upgrade Guide Tutorial


      One thing to remember is that you need MegaCli to do the flashing. You also need the correct file, I tried at least 2 different Perc 6 firmwares from Dell that kept getting rejected as corrupt by MegaCli (they were really the wrong version).  I have an external PCI-E Dell 6 Perc/I but I chose images from the 'Integrated" on motherboard version as it was all I could find.  They are different, and below is my first time finding success.........
  • Dell Perc 6/i cannot downgrade


    I flashed an LSI Logic firmware to it and it broke the BIOS (cannot do Ctrl+R) for booting purposes but allows other functionality to work normally. I tried downgrading to a Dell firmware for Perc 6i but it won't work, not even with MegaCli wget http://downloads.dell.com/FOLDER00416606M/1/SAS-RAID_Firmware_W83M2_LN32_6.3.1-0003_A14.BIN --2013-08-26 12:53:39--  http://downloads.dell.com/FOLDER00416606M/1/SAS-RAID_Firmware_W83M2_LN32_6.3.1-0003_A14.BIN Resolvi........
  • LSI MegaRAID Adventures, Guide and HowTo


    LSi Megaraid At first it was configured as a RAID 0, then I deleted the Virtual Disk Group. I thought both drives would be shown and detected in Linux as sda and sdb but it actually shows nothing. To make them work you have to hit Ctrl+R before the system boots (when prompted) and create a Virtual Disk Group.  In my case I created each one as RAID 0 (with a single drive only) as I just wanted JBOD but there is no such option or default in these Dell Pe........
  • WD 20EARX Dead Again


    Another new drive bad from the start:   Jun  2 15:14:18 one-desktop kernel: [15895.386779] ata2.00: exception Emask 0x50 SAct 0x1 SErr 0x280900 action 0x6 frozen Jun  2 15:14:18 one-desktop kernel: [15895.386782] ata2.00: irq_stat 0x08000000, interface fatal error Jun  2 15:14:18 one-desktop kernel: [15895.386784] ata2: SError: { UnrecovData HostInt 10B8B BadCRC } Jun  2 15:14:18 one-desktop kernel: [15895.386788] ata2.00: cmd 60/0........
  • Bad Hard Drive Slows Down Computer


    Here's a proven example of what a bad hard drive can do, it was technically functioning OK in a RAID array but the system became extremely low and the load become high and IOWAIT was even higher and I always thought it was a bad application.  The truth is that this failing 1TB Hitachi has slowly gotten worse and caused huge slowdowns, (eg. 100% load on Thunderbird waiting for e-mails to load etc..).  After swapping it out, tabs change instantly, emails are not lagged, and........
  • Ubuntu 10 Nvidia Drivers Not Updated After Kernel Update Solution/How-To Manually Rebuild nvidia kernel modules for Ubuntu


    I dread updating the kernel and rebooting to find the Ubuntu graphics aren't working and you have to manually intervene.   This is usually because Ubuntu for whatever reason didn't update the drivers you need (eg. the manually compiled Nvidia Kernel driver that MUST be recompiled for each and every kernel update unfortunately). The most common reason may be that "linux-source" hasn't been installed automatically on my system.  I tried to manually reinstall the........
  • How To Test If Your Hard Drive Is Good/Signs of dying hard drive


    I like dd, although it only reads it, usually a read test of the entire disk will uncover if your hard drive is bad in some parts.  This is a good thing to do at least once a month, a lot of times bizarre program behavior, laginess and crashing/unnmounting problems etc.. are due to a failing disc and SMART won't know it or indicate a problem: We must also remember there's never a guarantee, I've found that ever since we moved to larger and more platters per drive with 1TB drives........
  • smart is not smart, it thinks a dead drive is still good


    I had a dying drive that smart thought until it totally disappeared was a good drive, and actually all parameters did look fine but this system was causing my system to lockup and other bad behavior:   === START OF INFORMATION SECTION === Device Model:     WDC WD20EARS-00MVWB0 Serial Number:    WD-WMAZ20139 Firmware Version: 50.0AB50 User Capacity:    2,000,398,934,016 bytes Device........
  • Hitachi 2TB HDS5C3020ALA632 drive DOA


    I had one of these shipped and it was not recognized when plugged in, here's what a dead drive looks like (I assume it's teh circuit board which is dead):   ata1: link is slow to respond, please be patient (ready=0) ata1: softreset failed (device not ready) ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata1: link online but device misclassified, retrying ata1: link is slow to respond, please be patient (ready=0) ata1: softreset f........
  • SMARTCTL additional SMART command testing using short and long tests


    smartctl -t long /dev/sda (note you can specify short, but it's not as thorough as long of course). smartctl version 5.38 [i686-pc-linux-gnu] Copyright (C) 2002-8 Bruce Allen Home page is http://smartmontools.sourceforge.net/ === START OF OFFLINE IMMEDIATE AND SELF-TEST SECTION === Sending command: "Execute SMART Extended self-test routine immediately in off-line mode". Drive command "Execute SMART Extended sel........
  • MySQL NEVER delete ib_logfile0 or ibdata1 or you'll lose data


    don't delete /var/lib/mysql/ib_logfile0 or ibdata1 or mysql won't restart I didn't realize they were internal and not part of replication like the relay files! /usr/libexec/mysqld: ready for connections. Version: '4.1.22-log'  socket: '/var/lib/mysql/mysql.sock'  port: 3306  Source distribution 110127 16:31:00 [Note] /usr/libexec/mysqld: Normal shutdown 110127 16:31:00  InnoDB: Starting shutdown...........
  • mdadm/md-check how to check array integrity without rebuilding


    This doesn't seem to be widely known (maybe it's in some documentation that none of us read though) but there's an easy way to check the integrity of any mdadm array: sudo echo check > /sys/block/md0/md/sync_action -bash: /sys/block/md0/md/sync_action: Permission denied sudo will never work, this only works as root since echo is not actually a binary/command.  It is built-into bash. /sys/devices/virtu........
  • Ubuntu/Debian DRBD 8.0 Setup Guide


    I've only used it on Centos, so I thought I'd make a quick Debian guide: Install the DRBD Package apt-get install drbd8-utils Reading package lists... Done Building dependency tree       Reading state information... Done The following packages were automatically installed and are no longer required:   libswfdec-0.8-0 Use 'apt-get autoremove' to remove them. The following........
  • WD (Western Digital) Advanced Format Drive Lagged/Slow Speed/Performance/Design Flaw EAD/EARS problem WDC WD20EARS-00S8B1


    Let the numbers speak for themselves, from what I read the Load_Cycle_Count which is very high (more than 500,000/half a million times) is the number of head parks.  What a stupid "Green" design and design flaw which will probably mean an early life for the drive. This is almost as silly as Seagate's new reputation for BSY/poor quality disks since the 7200.11 series. To make it worse this is also when Western Digital introduced "Advanced Format" o........
  • Seagate Drive 500GB Drive Dying


    This drive is clearly on the way out, the Kernel knows it but I'm surprised that SMART is not concerned.  I didn't blame Seagate for their past issues until now.  This hard drive has hardly been used and has not even been powered on for a year according to SMART. Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Model Family:     Seagate Barracuda 7200.11 Device........
  • Seagate 7200.11 firmware defect in 500GB, 1000GB (1TB) and 1500GB (1.5TB) Hard Drives


    Seagate Inventory/Firmware Check I heard about this issue a long time ago but never looked into it.  I figured I wasn't affected since my 500GB drives were running for so long.  I've been using Seagate's since 2002 and to this day all of the drives I have are alive from Seagate. *Update the bad news is that I realize one of my 500GB's is about to die, it's not even a year old, but is also not affected by the recall according to Seagate! Seagate Inventory/Firm........
  • heartbeat is stopped for some reason


    heartbeat is stopped for some reason Anyway hnode2 was active and the services are running fine but I see heartbeat has been stopped somehow. Here is the last log I see of heartbeat: [quote:23c84415f5] Sep 9 17:15:32 hnode2 heartbeat: [16738]: info: MSG stats: 9/1762471 ms age 0 [pid16738/MST_CONTROL] Sep 9 17:15:32 hnode2 heartbeat: [16738]: info: cl_malloc stats: 716/51784021 152624/74519 [pid16738/MST_CONTROL] Sep 9 17:15:32........
  • Latest Articles

  • syntax error, unexpected T_SL in PHP Solution
  • grep regular expression match number range between specific numbers
  • bash how to print out lines of text within a range from the first occurrence
  • bash script how to to check LAN computers for open ports
  • MySQL Using mytop Debug Source of High IO and Slow Performance
  • How To Mathematically Convert and Calculate Binary Value To Decimal Value
  • systemd management using systemctl and journalctl to check systemd logs
  • css how to format code in the code tag
  • css br with extra blank line
  • What is /dev/pts and why do we need it in Linux?
  • Linux What is umask (user mask) for file and directory creation permissions and how to calculate umask and change the defaults
  • Linux Permissions and Groups Real Usecase for Group Access
  • Centos 7 python34 how to install the gi library
  • Centos 7 - Convert Minimal to Graphical GUI GNOME or KDE Desktop
  • AMD Set Fan Speed and Other Powerplay Memory/CPU Timings with a Linux script
  • Ethereum Mining Claymore Nanopool Error
  • genisoimage errors with long filenames and deep directory structures
  • Linux Kernel USB Export Errors
  • How to download gajim 0.16.9 XMPP/Jabber client so you can use OMEMO encryption
  • HP DL385 G7 Linux BIOS Update Flash