• Cisco Unified Communications Manager Express Cheatsheet CUCME CME


    Getting started, let's enable ephones and DNs we can add a phone with a telephone number: Router>en Router#conf t Router(config)#telephony-service !this enables ephone registration otherwise phones cannot register Router(config-telephony)#ephone-reg !max-ephones 2 says we can have a maximum of 2 phones, change to your needs (or to the limit set by your IOS image) Router(config-telephony)#max-ephones 2 ........
  • How to install and setup LXC Containers (OpenVZ alternative) on Centos 6 / 7


    If you don't aleady have it, you'll need EPEL Install LXC yum -y install lxc lxc-templates Loaded plugins: fastestmirror Setting up Install Process Loading mirror speeds from cached hostfile * base: mirror.it.ubc.ca * epel: mirrors.kernel.org * extras: mirror.it.ubc.ca * updates:........
  • iSCSI on Centos 7 Configuration and Setup Guide for Initiator and Target


    initiator = client target = server These are the first concepts you should understand which is that in iscsi essentially the "initiator" is the client and the "target" is the server. iSCSI is derived from the old fashioned SCSI that us oldtimers grew to love. The "i" stands for Internet and the SCSI stands for "Small Computers Systems Interface" (SCSI). iSCSI Target (Server)Setup targetcli is the pac........
  • How Does Cisco CUCM (Cisco Unified Communication Manager) Work?


    Cisco's CUCM (Cisco Unified Communication Manager) is a system that combines voice, video, data and mobile products into a single unified management suite. At its core, the CUCMis like a "Super PBX" that controls the flow of all communications through an organization even single or multiple site deployments. Cisco's CUCMmakes communication more effective and simple through centralized management and unification of communications resources.........
  • How To Mathematically Convert and Calculate Binary Value To Decimal Value


    When converting binary the easiest way is to write out a vertical list in a format like below and follow the formula in the table. Example Convert 1101 1111 to decimal. Step 1.) Write out the binary below in vertical form (leave lots of space on the left side). Keep this in mind that the "previous sum" starts at 0 on your first line. Step 2.) Formula: 2 *........
  • systemd management using systemctl and journalctl to check systemd logs


    systemd is like the service manager for your Centos and other modern Linux distributions (including Debian/Mint/Ubuntu) allows you to enable services, stop them, restart them, check their status and even reboot your system. The key commands or arguments you will use with systemctl are the following: Unit Commands: list-units [PATTERN...] List loaded units &nbs........
  • VMWare ESXi 6.7 SSH/PowerShell CLI Commands


    [root@localhost:~] BootModuleConfig.sh echo host-ind nfcd........
  • Centos 7 - How To Install NFS and Mount Remotely


    Server Side Config 1.) First install nfs-utils yum -y install nfs-utils 2.) Configure nfs share Create a directory for your NFS share mkdir /datastore Create your NFS share in /etc/exports echo "/datastore 10.220.101.0/24(rw,sync,no_root_squash)" >> /etc/exports systemctl restart nfs........
  • VMWare 6.7 VCSA VSphere ESXi Management SSO Install Guide on Linux using the CLI


    #mount the VCSA DVD mount /dev/sr0 /mnt/cd #alternatively you could mount the iso directly mount -o loop vcsa.iso /your/mount/path #for this purpose we are using the CLI installer on Linux cd /mnt/cd/vcsa-cli-installer/lin64 #no it's not going to be that easy you can't just run vcsa-deploy like that you need to use a template or configured .json file ./vcsa-deploy Usage: vcsa-deploy [-h] [--version] [--supported-deploymen........
  • Disable SSH Password Authentication to Increase Security and Harden SSH Linux Unix Server Ubuntu Mint Centos Debian


    Just a note before you do this you should have a sure, guaranteed way into the system such as local, KVMor preferably publickey making bruteforce SSH absolutely impossible since there is no password to bruteforce and even if someone knew the password they wouldn't be able to login except from the local console (presumably you should make sure no one unauthorized has physical access). 1. Edit /etc/ssh/sshd_config Find the section like this:........
  • Centos 7 Cudaminer Nvidia setup guide


    I am using a GTX 1060 but replace the download for the driver with the correct/current version for your particular card by visiting: http://www.nvidia.com/Download/index.aspx?lang=en-us yum install automake curl openssl-devel libcurl-devel gcc gcc-c++ yum -y install kernel-devel-`uname -r` yum -y install unzip #the........
  • Linux Mint Install Netboot PXE Guide Howto


    *Update so this doesn't work it must be something to do with the path of nfs or something else but the installer fails with "Installer crashed" at the end whereas with the CD/USB it works. This assumes you've already installed and configured a separate PXE/DHCP server somewhere else and your /tftpboot directory is setup. This is for Linux Mint 18.1 but generally applies to most versions although you may have tro change things like "casper"........
  • wget how to resume download!


    It's very simple you just use the "-c" switch and wget will resume the file (make sure you are in the same directory) or specify -O /path/to/partialdownload.zip wget -c http://someurl/file.zip........
  • mcp55 NIC not working at boot on Centos 6.6-6.8


    forcedeth 0000:00:08.0: irq 25 for MSI/MSI-X forcedeth 0000:00:08.0: eth0: MSI enabled forcedeth 0000:00:08.0: eth0: no link during initialization ADDRCONF(NETDEV_UP): eth0: link is not ready forcedeth 0000:00:08.0: eth0: link up ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready Dec 1 18:21:32 box15 kernel: forcedeth: Reverse Engineered nForce ethernet driver. Version 0.64. Dec 1 18:21:32 box15 kernel........
  • Linux Debian/Ubuntu/Centos How To Force Internet Traffic Through PPTP L2TP OpenVPN Account Only


    The following assumes the computer is local/physical to you and/or it always has a LANIP so it can be accessed on site without having a default gateway. The key to this is not to set a default gateway for your computer or you can set a script on boot or other time to delete the gateway (where eth0 is the NIC you are using): route del default eth0 50.80.20.2 is the VPN server you connect to 192.168.1.1 is your........
  • Centos Add Multiple IP Addresses in a range without manually setting each static IP


    This is actually very simple and this example assumes your network device is "eth0" In Centos your network config would be the following: /etc/sysconfig/network-scripts/ifcfg-eth0 Take the same path and just add a "-range0" So to add a range create the following file: /etc/sysconfig/network-scripts/ifcfg-eth0-range0 IPADDR_START=192.168.1.50 IPADD........
  • VPN Account Buyers Guide and General Info


    What does VPN stand for? VPN stands for Virtual Private Network and is a secure way of connecting networks and devices. In the context we're talking about it will usually be a client-server solution and not connecting whole networks or businesses. The assumption is that most people reading this are trying to secure their internet connection, privacy and hide or change their IPaddress. Why use a VPN? There are many........
  • WHMCS Sending Blank E-mails Solution


    After the "latest" update one of our clients asked us to figure out the issue and it turns out it is related to the mail settings. Basically all e-mails were being sent with blank text/no body. The solution Go to "Setup ->General Settings ->Mail" and just click on "Save" and it will work again. Note that this assumes you didn't break things yourself by changing any settings. WHMCS may tell y........
  • How to read a conf file without the comments


    cat /etc/some.conf|grep -Ev '^#|^;|^$' This assumes that comments start with # or ; (adjust as necessary). Also note that the ^$ omits blank lines.........
  • CPanel suhosin install failed


    /scripts/phpextensionmgr install PHPSuHosin Updating md5sum list Fetching http://httpupdate.cpanel.net/cpanelsync/easy/targz.yaml (connected:0).......(request attempt 1/12)...Resolving httpupdate.cpanel.net...(resolve attempt 1/65)... Fetching http://httpupdate.cpanel.net/mirror_addr_list (connected:0).......(request attempt 1/3)......connecting to 74.50.120.123...@74.50.120.123......connected......receiving...100%......request success......Done........
  • Dell Perc 6/i cannot downgrade


    I flashed an LSI Logic firmware to it and it broke the BIOS (cannot do Ctrl+R) for booting purposes but allows other functionality to work normally. I tried downgrading to a Dell firmware for Perc 6i but it won't work, not even with MegaCli wget http://downloads.dell.com/FOLDER00416606M/1/SAS-RAID_Firmware_W83M2_LN32_6.3.1-0003_A14.BIN --2013-08-26 12:53:39-- http://downloads.dell.com/FOLDER00416606M/1/SAS-RAID_Firmware_W83M2_LN32_6.3.1-0003_A14.BIN Resolvi........
  • WD 20EARX Dead Again


    Another new drive bad from the start: Jun 2 15:14:18 one-desktop kernel: [15895.386779] ata2.00: exception Emask 0x50 SAct 0x1 SErr 0x280900 action 0x6 frozen Jun 2 15:14:18 one-desktop kernel: [15895.386782] ata2.00: irq_stat 0x08000000, interface fatal error Jun 2 15:14:18 one-desktop kernel: [15895.386784] ata2: SError: { UnrecovData HostInt 10B8B BadCRC } Jun 2 15:14:18 one-desktop kernel: [15895.386788] ata2.00: cmd 60/0........
  • WD 20EARX 2TB Bad within days


    This is just trying to read 5GB off the drive with dd and the drive initially tested ok but shortly after I wondered why I was seeing 2MB/s read speeds. Notice the "current_pending_sector", anytime I've seen it at anything above 0 even with no other bad fields/attributes, it means the drive is bad. ata1.00: exception Emask 0x0 SAct 0x3 SErr 0x0 action 0x0 ata1.00: irq_stat 0x40000008 ata1.00: failed command: READ FPDMA QUEUED ata1.00: cmd 60/00:00:........
  • Directadmin error/** Found 7 pre-existing rpmdb problem(s), 'yum check' output follows: e2fsprogs-devel-1.41.12-3.el6.i686 has missing requires of e2fsprogs-libs = ('0', '1.41.12', '3.el6') e2fsprogs-devel-1.41.12-3.el6.i686 has missing requires of l


    Solution To The Following: yum -y install zlib-devel yum -y install e2fsprogs* *** Cannot find /usr/include/et/com_err.h. (yum install libcom_err-devel) *** Installation didn't pass, halting install. Once requirements are met, run the following to continue the install: cd /usr/local/directadmin/scripts ./install.sh Common pre-install commands: http://help.directadmin.com/it........
  • Bad Hard Drive Slows Down Computer


    Here's a proven example of what a bad hard drive can do, it was technically functioning OKin a RAID array but the system became extremely low and the load become high and IOWAIT was even higher and I always thought it was a bad application. The truth is that this failing 1TBHitachi has slowly gotten worse and caused huge slowdowns, (eg. 100% load on Thunderbird waiting for e-mails to load etc..). After swapping it out, tabs change instantly, emails are not lagged, and........
  • Setup PXE Boot using Centos and dhcpd, tftp and syslinux


    This is something I often setup for clients because it's very helpful for people in datacenters, this allows custom OS installs on demand, you can customize it more by using kickstart etc.. but here's a base I use before customizing more: This little script below will install everything you need to get booting by PXE Linux. It also assumes you set a local IP (be sure not to overwrite your existing IP) on eth0:0 (note the :0) as 192.168.1.10 and it........
  • Samsung Galaxy Note Upgrade to ICS 4.0 microSDHC card not detected/dataloss after upgrading - possible solutions


    I backed up everything in the /mnt/sd_card directory thinking that some dataloss could occur for some reason but purposely left my microSDHC unbacked up thinking that "it won't touch that since it's external" and Samsung's and other manufacturers website even say this (that it won't be affected and not to worry etc). Apparently I was wrong, my microSD was "undetected" and asked to be formatted after the upgrade (there goes 3-months worth of family photos). No........
  • xen how to resize an image properly


    The best way I could figure out is to use another guest of some sort to do this, while assigning the disk that needs to be resized to the same guest. So say we have /dev/xvda as the guests drive and we've booted it up. We also have /dev/xvdb (this is going to be the image/disk to be resized). In this case it's based on an ext3/4 image. Run e2fsck on it to ensure there are no filesystem errors. e2fsck /dev/xvdb........
  • mdadm how to add a device to an array after a failure


    This array is a RAID 1 and in this case 1 of the 2 drives failed (a WD drive and I've found them to be the weakest and most unreliable of any brand and are easily damaged/DOA when shipping them). mdadm --manage /dev/md0 --add /dev/sdb1 The above assumes the array you want to add to is /dev/md0 and the device we are adding is /dev/sdb1 *One thing to remember is to make sure the partition you are adding is the correct size for the array. You can also g........
  • Asus VE247H 23.7" Inch LCD/LED Backlit Monitor Dead/Stuck Pixel Policy Complaint


    I've thought for awhile that Asus has been banking on its years old reputation for quality amongst gamers and enthusiasts and I think I'm right. My Asus VE247H Monitor with a supposed 2MS refresh rate has 1 red/stuck/dead pixel but fortunately it can only be seen on a non-true black picture or against a blue screen. I have several Asus products and find they're all of fairly poor quality. First of all their motherboards have given me the most issues of any brand, they te........
  • Xen how to mount disk images off-line and access data


    fdisk -lu VPS.img last_lba(): I don't know how to handle files with mode 81ed You must set cylinders. You can do this from the extra functions menu. Disk VPS.img: 0 MB, 0 bytes 255 heads, 63 sectors/track, 0 cylinders, total 0 sectors Units = sectors of 1 * 512 = 512 bytes Device Boot Start End ........
  • How To Burn ISO Image using cdrtools/dvdrtools for Linux/Unix Ubuntu/Debian/RHEL/Centos etc..


    It really is as simple as: cdrecord -v dev=/dev/sr0 pathtoyourisoimage.iso -v is for verbose, I prefer it but if you don't you won't see as much output like below (I like to know the details and exactly what's happening) dev=/dev/sr0 specifies the device name of your burner (they say not to use it and to specify some weird annoying device string but using the raw /dev has always worked for me and is how it should have been implemented from the start IMHO)........
  • MySQL Import CSV data tutorial guide


    It's actually fairly straight forward: load data local infile 'billpayments-payments.csv' into table payments fields terminated by ',' enclosed by '"' lines terminated by 'n' The above assumes that your fields are terminated by a comma (some programs like OpenOffice change this to a semi-colon ;) and that they are enclosed with " The above will insert the data from billpayments-payments.csv into the table payments.........
  • wget download all files on page/directory automatically recursively


    Have you ever found a website/page that has several or perhaps dozens, hundreds or thousands of files that you need downloaded but don't have the time to manually do it? wget's recursive function called with -r does that, but also with some quirks to be warned about. If you're doing it from a standard web based directory structure, you will notice there is still a link to .. and wget will follow that. Eg. let's say you have files in http://serverip/documen........
  • How to view UDP and other protocol connections?


    netstat is weak and can't show udp connections and most other protocols, use "ss" which is what netstat should have been: The "-u" switch stands for udp, here's a list of other options: Usage: ss [ OPTIONS ] ss [ OPTIONS ] [ FILTER ] -h, --help this message -V, --version output ver........
  • Linux Out of Memory OOM Object Killer Solution "Out of memory: kill process 1955 (sshd) score 81 or a child"


    I had a system running a 128MB live CD image with 2.8 gigs of available RAM and the OOM kernel killer went crazy when using dd for more than 8 minutes and kept killing everything. I've read that this is due to a low-memory issue and paging in the kernel and 32-bit systems with lots of RAM. I even enabled swapspace on my LiveCD and the issue happened 25 minutes into dd rather than 8 minutes, so what gives? Also no swap space was ever used! cat /proc/s........
  • How To Test If Your Hard Drive Is Good/Signs of dying hard drive


    I like dd, although it only reads it, usually a read test of the entire disk will uncover if your hard drive is bad in some parts. This is a good thing to do at least once a month, a lot of times bizarre program behavior, laginess and crashing/unnmounting problems etc.. are due to a failing disc and SMART won't know it or indicate a problem: We must also remember there's never a guarantee, I've found that ever since we moved to larger and more platters per drive with 1TB drives........
  • smart is not smart, it thinks a dead drive is still good


    I had a dying drive that smart thought until it totally disappeared was a good drive, and actually all parameters did look fine but this system was causing my system to lockup and other bad behavior: === START OF INFORMATION SECTION === Device Model: WDC WD20EARS-00MVWB0 Serial Number: WD-WMAZ20139 Firmware Version: 50.0AB50 User Capacity: 2,000,398,934,016 bytes Device........
  • Openvz YUM Error Solution to "[Errno -1] Metadata file does not match checksum Trying other mirror."


    It's weird because I have a nearly identical box and setup and I can update the ovzkernel-PAE* just fine but on this box it doesn't work. I only get this error with the openvz.repo and not others such as Centos-Base.repo With my other server it works normally: ================ Setting up Update Process Resolving Dependencies --> Running transaction check ---> Package ovzkernel-PAE.i686 0:2.6.18-238.12.1.el5.0........
  • Hitachi 2TB HDS5C3020ALA632 drive DOA


    I had one of these shipped and it was not recognized when plugged in, here's what a dead drive looks like (I assume it's teh circuit board which is dead): ata1: link is slow to respond, please be patient (ready=0) ata1: softreset failed (device not ready) ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata1: link online but device misclassified, retrying ata1: link is slow to respond, please be patient (ready=0) ata1: softreset f........
  • How to recover from dead DRBD partition/hard drive in two simple commands


    This assumes that you've at least created the correct partition for your DRBD already. Notice that I am "diskless", that's because either your DRBD partition doesn't exist/has been renamed (eg. sdb becomes sda when sdb dies and you reboot) or because that drive is really actually dead/gone. *If you need to permanently change the partition/device for your resource be sure to edit /etc/drbd.conf on both hosts and reload the config. (replace r0 with........
  • vnstat setup guide/tutorial


    yum -y install vnstat chown nobody.nobody -R /var/lib/vnstat/ #replace venet0 below with your desired interface sudo -u nobody vnstat -u -i venet0 #edit: vi /etc/sysconfig/vnstat #VNSTAT_OPTIONS="-i venet0" # only use the sed below if you are using venet0 instead of eth0 or replace accordingly sed -i 's/eth0/venet0/g' /etc/sysconfig/vnstat [root@monitor]# yum install vn........
  • OpenOffice Calc SUM function not working Solution - Result is always 0/apostrophe appears in front of all numbers.


    I right clicked all applicable cells and chose "number" but that's enough. I notice when I click the cell there is an invisible ' in front of the number: '33.64 Calc imported my CSV and decided to add a ' in front of the numeric currency values!!!*Actually the problem occurs when you right click the cells and change the type from text to number, no matter what format you choose. If I change it to be currency i........
  • yum in Centos 5/Xen halts and exits suddenly


    yum exits in the middle The problem is this VPS seems to be an OpenVZ template from HyperVM. The only way to make it work was to disable i386 packages since this was an x64 kernel. That shouldn't be necessary but it was the only way to make yum stop quitting after the first package or two. I couldn't find any issue by checking the logs either. echo y|yum install vim-minimal telnet expect jwhois net-tools slocate iptables elinks gawk L........
  • mdadm RAID 1 adventures


    I separated the 2 drives in the RAID 1 array. 1 is the old one /dev/sda and is out of date, while the separated other one /dev/sdc was in another drive and mounted and used with more data (updated). I wonder how mdadm will handle this: usb-storage: device scan complete md: md127 stopped. md: bind md: md127: raid array is not clean -- starting background reconstruction raid1: raid set md127 active with 1 out of 2 m........
  • Openvz Live Migration Error - Error: undump failed: Invalid argument Restoring failed: Error: iptables-restore exited with 2 Error: Most probably some iptables modules are not loaded Error: rst_restore_net: -22


    Adding IP address(es): 192.168.5.8 192.168.5.9 Setting CPU units: 1000 Error: undump failed: Invalid argument Restoring failed: Error: iptables-restore exited with 2 Error: Most probably some iptables modules are not loaded Error: rst_restore_net: -22 Container start failed Stopping container ... Container was stopped Container is unmounted Error: Failed to undump VE Resuming... vzquota : (erro........
  • exim high load and dozens of processes


    This server was experiencing loads of up to 80 and maxing out the RAM and kmemsize on a CPanel VPS. There were literally dozens if not hundreds of exim processes. I have no idea why exim has such a design that would allow it to consume this much CPU and RAM. Any normal MTA should not be spawning so many processes, it should be processing them in sequence and if it is going to spawn hundreds of processes in response to a large volume of mail, it's better to have a delayed del........
  • Linux Burn MP3 CD On the Fly using


    I finally decided to look into some utils that did this, and the first one I found is "mp3burn". It is unbelievable simple and perfect. *2017-11 update and mp3burn is still available in standard repos such as Ubuntu 14/16 so this is a current and working project. Just install the package and it gets all required libraries to convert and then burn's on the fly. And you won't believe how simple it is. I just want to a directory that had the MP3's I wanted t........
  • Check How Many Watts Your CPU,HDD,GPU, Fans Use - Power Consumption Tool


    www.antec.outervision.com/index.jsp I found that wattage/power consumption tool to be very useful, especially when you're worried that you're hitting the Power Supply's limit. You'll see very quickly that different CPU's, Graphics, Cards, HDDS use a wide range of energy. That tool can help you choose a build that won't stress or go over the maximum limits of your Power Supply.........
  • Centos 5.5 RAID 1 boot issue


    I installed 5.5 with a 300GB RAID 1 partition (boot is also on this partition). It booted up fine the first few times until after I used a Live CD and accessed the array, and it became named /dev/md127 for some reason. Now whenI boot into CentOS I get a kernel panic and different errors, once I got "invalid superblock", even though the array is fine (it didn't happen again, probably because I was sure to dismount and stop the mdadm array properly). Here's what........
  • Seagate Drive 500GB Drive Dying


    This drive is clearly on the way out, the Kernel knows it but I'm surprised that SMART is not concerned. I didn't blame Seagate for their past issues until now. This hard drive has hardly been used and has not even been powered on for a year according to SMART. Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.11 Device........
  • Seagate 7200.11 firmware defect in 500GB, 1000GB (1TB) and 1500GB (1.5TB) Hard Drives


    Seagate Inventory/Firmware Check I heard about this issue a long time ago but never looked into it. I figured I wasn't affected since my 500GB drives were running for so long. I've been using Seagate's since 2002 and to this day all of the drives I have are alive from Seagate. *Update the bad news is that I realize one of my 500GB's is about to die, it's not even a year old, but is also not affected by the recall according to Seagate! Seagate Inventory/Firm........
  • Linux AHCI Hotswap Tips - Remember To Reread The Partition Table WITHOUT rebooting


    From the package "parted" you can use the command "partprobe" to re-read the partition table. I really hate rebooting, and that's what Iloved to hear about AHCI motherboards, that they allow hotswap so you don't have to reboot. But that's only as good as the OS, if the OS does not reload the partition table you won't be able to do anything with that new drive you attached without rebooting. Yes, even without re-reading the partiton table Linux will........
  • Picking an FTPD (vsftpd) Server in Linux Centos/Debian


    I decided on using yum to help me decide even though I normaly use proftpd I decided to see what else I could find. yum search ftp Loaded plugins: fastestmirror Loading mirror speeds from cached hostfile * rpmforge: ftp-stud.fht-esslingen.de * base: mirrors.netdna.com * updates: updates.interworx.info * addons: yum.singlehop.com * extras: mirrors.netdna.com rpmforge........
  • OpenVZ backup container to a single file while it's running using "vzdump"


    Proxmox has made this free utility to backup running OpenVZ containers. It's a great program which is actually just a PERL script but gets the job done. This program is not 100% required because all it really does is cp -a from your container's path as far as I know but it is still good to have uniformity to how you backup your containers. For RPM distros such as Centos/RHEL/Fedora etc.. download and install this: wget http://www.proxmox.com/cms_proxm........
  • PHP cannot access /usr/bin/openssl


    PHP cannot access /usr/bin/opensslI have verified the username that runs the process is able to access /usr/bin/openssl and it does exist but the PHP script is saying it doesn't exist: [code:1:1fd0f3abbe] if (!file_exists($OPENSSL)) { //echo "ERROR: OPENSSL $OPENSSL not foundn"; }[/code:1:1fd0f3abbe] I don't get itI can clearly see the contents of /usr/bin by using the PHP system fu........
  • JavaScript how to do math arithmetic with floats and int


    JavaScript how to do math arithmetic with floats and intI have 3 variables some of which are just int and some float and need to find their sum It just adds them as strings for some reason.Normally this would work but the floats were actually text technically I guess since they came from a form. You need to convert them using parseFloat() and then everything is fine.........
  • Setup Static IP Address ONBOOT


    Setup Static IP Address ONBOOTAssuming you are using eth0 Note this will work for any version of CentOS and basically any version of Redhat Linux or Redhat based distribution. You would need to create a new file [code:1:02f8d34c30] /etc/sysconfig/network-scripts/ifcfg-eth0:0[/code:1:02f8d34c30] DEVICE=eth0:0 the ":0" at the end specifies alias 0 we could actually change this to ":99" or "........
  • The New Chips on the Block


    The New Chips on the BlockThe New Chips on the Block By Bruce Gain Story location: http://www.wired.com/news/infostructure/0,1377,67795,00.html 02:00 AM Jun. 13, 2005 PT We have embarked upon a new era in x86 PC computing -- so say chip giants AMD and Intel following their launches of dual-core PC processors. So how will dual-core processing change your PC computing experience? Our FAQ should help you decide whether or when you sho........
  • CDR Manufacturers - Why is so much media bad?


    CDR Manufacturers - Why is so much media bad?I have searched for good media and tried many kinds for years. I guess I'll try to summarize my findings and conclusions. Dye is irrelevant, dye of any color can be good or bad, it more likely depends on the manufacturer. Speaking of manufacturers, the name at the top of the disc means nothing. For example, Memorex along with any other 'brand' is actually always made by another manufaturer including CMC Mag........
  • MySQL Restoring And Dumping/Backing UP MySQL Data/Tables/Databases


    Backing MySQL Databases Backing Up/Dumping All Mysql Databases To A Single File mysqldump --all-databases -u admin -p > allmysqldatabases.sql The "-all-databases" clause is pretty obvious isn't it? It means that it will backup all databases. The "-u admin" means login using the user "admin", if you h........
  • iPhone 3GS Jailbreak Information & Benefits


    Truly, the only way to unleash the capabilities and customization abilities of iPhone are to jailbreak, it's not just for hackers anymore. A few days ago someone by the named of "geohot" released a single click application called "purplera1n", which does the entire operation smoothly and seamlessly. In our case, the first time it went as far as "done, wait for reboot" on our Windows machine and for minutes we waited and saw the pic on the iPhone w........
  • Apple iPhone 3GS and predecessors are leading a revolution


    As much of a computer nerd as Iam, I'm usually a late adopter to technology for a few reasons. Ifeel most new hyped technologies and electronics are mainly fads, and I'm also cheap. Adopting later means you avoid the bugs, kinks and most importantly pay the lowest price, that's me being cheap again :) I never read much about the iPhone but Isaw all the hype around it and until recently I wasn't a big fan of anything Apple until a few years ago I realize........
  • resume: could not stat the resume device file


    resume: could not stat the resume device file I got that after migrating to a different physical hard drive, it wanted to resume from a swap partition that no longer exists. This is actually controlled by "uswsusp.conf" in /etc Just edit it and remove the device or change it to the correct new swap file.........
  • Rackable Systems and their Microslice Clustered 1U Servers


    Ithink there has been a lot of negative press towards Rackable Systems. We will give their new solution credit that it is marketed very well, and comes prepackaged and ready to go. But let's cut through the hype of both sides, the people who love this concept and the people who hate it. What Rackable Systems have done is a first, to minimize space, power and costs into small servers. This is great, and many companies have already built their own servers based........
  • BIND/NAMED woes


    Feb 5 01:39:33 server named[19768]: zone myzone.com/IN: serial number (12331465) received from master 127.0.0.2#53 < ours (200901281) The above is taken from /var/log/messages This can be annoying, it can happen for a variety of reasons. What seems to be happening here is that the slave realizes the time on the slave is ahead of the master, so it therefore assumes it has the most up to date copy and won't actually transfer the zone. The solutio........
  • Latest Articles

  • Linux Ubuntu Cannot Print Large Images
  • Cannot Print PDF Solution and Howto Resize
  • Linux Console Login Screen TTY Change Message
  • Apache Cannot Start Listening Already on 0.0.0.0
  • MySQL Bash Query to pipe input directly without using heredoc trick
  • CentOS 6 and 7 / RHEL Persistent DHCP Solution
  • Debian Ubuntu Mint rc-local service startup error solution rc-local.service: Failed at step EXEC spawning /etc/rc.local: Exec format error
  • MySQL Cheatsheet Guide and Tutorial
  • bash script kill whois or other command that is running for too long
  • Linux tftp listens on all interfaces and IPs by DEFAULT Security Risk Hole Solution
  • python import docx error
  • Cisco Unified Communications Manager Express Cheatsheet CUCME CME
  • Linux Ubuntu Debian Missing privilege separation directory: /var/run/sshd
  • bash how to count the number of columns or words in a line
  • bash if statement how to test program output without assigning to variable
  • RTNETLINK answers: Network is unreachable
  • Centos 7 how to save iptables rules like Centos 6
  • nfs tuning maximum amount of connections
  • qemu-kvm error "Could not initialize SDL(No available video device) - exiting"
  • Centos 7 tftpd will not work with selinux enabled