This is certainly a poor design, as you can read many seasoned admins who have updated their iDRAC only to have it killed. One possible cause is not by doing all the incremental updates, doing updates from an old iDRAC to one many revisions newer is a sure way to kill things, but even then there is no guarantee based on the amount of failures.
List of threads of people's dead iDRAC's:........
This can break things easily in remove environments where it was normally easy to convert a normal eth0 to a bridge under br0, and that bridge would normally have the same MAC address by default, which is desirable for most situations.
In Debian 11 this is different for some reason now.
https://unix.stackexchange.com/questions/681013/bridge-gets-random-mac-........
In today’s digital landscape, finding a reliable and secure Virtual Private Server (VPS) or Virtual Dedicated Server (VDS) goes beyond just comparing specs and prices. With increasing concerns over data privacy, security breaches, and government surveillance, the wisdom of choosing your VPS/VDS provider based on juri........
If you get this error, it is often because you have configured Apache with modules that weren't actually installed. Eg. you try to load the PHPmodule but didn't actually install the apache2 php module, so the server can't start. In general, this error can often be caused by issues with problematic modules and/or Apache being configured for modules that have not actually be installed (eg. libapache2-mod-php) is missing.
The above results in this less than obv........
This should work for most console ports of other manufacturers too. It is a quick and simple method for emegencies or deploying a few appliances/devices in a non-standard environment or small environment.
However, if this is a route thing, or the equipment is not physically close to you, it would be best to use some sort of "Terminal" server which is an IP connected switch with several serial ports built-in for this purpose. Normally they accessible by web/........
Welcome to our in-depth guide on configuring NVIDIA GPUs with Docker on Ubuntu. This post is tailored for developers, data scientists, and IT professionals who are looking to leverage the power of NVIDIA's GPU acceleration within Docker containers.
Whether you're working on machine lea........
haproxy is one of the best known and widely used Open Source load balancers out there and a strong competitor to nginx.
haproxy is used by many large sites per Wikipedia:
HAProxy is used by a number of high-profile websites including GoDaddy, GitHub,........
If you are installing ta-lib for Python and get this error then you can normally solve it by manually getting the ta-lib source files and compiling.
tar -zxvf ta-lib-0.4.0-src.tar.gz
cd ta-lib;./configure;make;make install
Collecting ta-lib
Downloading https://files.pythonhosted.org/packages/39/6f/6acaee2eac6afb2cc6a2adcb294080577f9983fbd2726395b9047c4e13ec/TA-Lib-0.4.26.tar.gz (272kB)
&nbs........
Virtualbox is a very powerful tool, but for some use cases it is less than optimal.
Say you are in a work, lab or other environment where you are not alone on the physical network and there could be overlap of IPs, but you need all of your VMs to be contactable from your host, VMs need to communicate with each other, and VMs need internet.
NAT Network will give you VM to VM communication and internet, however, it is buggy and unstable. It also doesn't allow host to VM co........
Are you new to the company, datacenter or a third party who is responsible for deploying a fleet of servers from scratch.
The first step is to normally login to the KVM so you can perhaps manually reinstall, PXE boot the Cloud Image or reimage/reinstall an OS but you need access to the KVM/IP or what Dell calls iDRAC.
It's common that you may have forgotten this information or that another employee or colleague has changed the info and did not tell you, that they have left the........
This is an ongoing issue even with the latest Thunderbird 102.x where attachments downloaded via IMAP just won't save or will be corrupt which is a huge interruption to workflow or if you come back later to find out the file you thought you saved is invalid/corrupt and you have perhaps deleted the e-mail.
How to solve the Thunderbird filesize attachment issue?
1. Click on "Settings". then go to "General".
2. Scroll to the bottom to find "Conf........
It may appear to be an Xorg or lightdm/gdm/mdm error but in reality for many users with this issue, it's a driver conflict and issue. I had a system that had two GPUs, an Intel and Nvidia GPU.
The only thing that got it working was to remove the nouveau driver and blacklist it so it never came back, then the Intel GPU works fine without these issues.
Solution
sudo rmmod nouveau
add nouveau/other driver to blacklist
edit th........
This can be used on almost anything, since Gluster is a userspace tool, based on FUSE. This means that all Gluster appears as to any application is just a directory.
Applications don't need specific support for Gluster, so long as you can tell the application to use a certain directory for storage.
One application can be for redundant and scaled storage, including for within Docker and Kubernetes, LXC, Proxmox, OpenStack, etc or just your image/web/video files or even da........
The Best Docker Tutorial for Beginners
We quickly explain the basic Docker concepts and show you how to do the most common tasks from starting your first container, to making custom images, a Docker Swarm Cluster Tutorial, docker compose and Docker buildfiles.........
In our 2024 VPS Server/Cloud Buyer's Guide, we place the location of your VPS/hosting/server as one of the priorities that is often overlooked.
2024 Update - Datacent........
1. Let's work from an environment where we can install Ansible on.
If you are using an older version of Linux based on Mint 18 or Ubuntu 16, you may want to get the PPA and get the latest version of Ansible that way:
sudo apt install gpg
sudo add-apt-repository ppa:ansible/ansible
sudo apt update........
For a lot of reasons, it may be convenient to detach or attach live disks to a running VM without having to reboot it. Sure, you can use some network based storage, but when performance counts, attaching a new virtual disk will usually give you better throughput and lower latency in a quick testing situation.
This doesn't work, why not?
drive_add 0 if=virtio,file=/tmp/vm.qcow2,if=virtio,format=qcow2,id=rtt
Can't hot-ad........
This was done on a 2900 but applies to all the switches of the same era.
Step 1 - Power Cycle and enter recovery mode
If you have physical access you can power cycle and hold the mode button down for 15 seconds. After that the SYS light will flash on the switch and you will see the following screenshot.
If you don't have physical access (eg. it is a datacenter swich over console only) then power cycle and hit "Ctrl+Pause/B........
It has been renamed to kde-spectacle so you install it like so:
sudo apt install kde-spectacle
You'll find it in your start menu listed as "Take Screenshot"........
kernel: [549267.368859] mate-terminal[7871]: segfault at 2000000101 ip 00007f5d0a9548f0 sp 00007fff7012c610 error 4 in libgobject-2.0.so.0.4800.2[7f5d0a920000+52000]
This seems to be a long-time bug in Mint mate-terminal where you sometimes move or detach a terminal and it crashes losing all of the other open terminal sessions.........
apt install software-properties-common
add-apt-repository ppa:deadsnakes/ppa
apt update
apt install python3-pip
apt install python3.7 curl gnupg python3.7-dev git
ln -s /usr/bin/python3.7 /usr/bin/python3
pip3 install numpy keras_preprocessing
curl https://bazel.build/bazel-release.pub.gpg | sudo apt-key add -
echo "deb [arch=amd64] http://storage.googleapis.com/bazel-apt stable jdk1.8" | sudo tee /etc/apt/sources.list.d/bazel........
Unless you are using OpenStack, AWS etc then cloud-init is just some bloat that slows down the booting of your VMand can actually halt it from booting if it doesn't have a proper working IP (not good!).
#remove cloud init!
Debian based Ubuntu / Mint
sudo apt remove cloud-init
RHEL / CentOS based
yum remove cloud-init
........
Symbolic link not allowed or link target not accessible: /path/httpdocs/news.html
There are a few reasons that can cause this message and this is for people who have ruled out the basics, eg. your symlinks are enabled and the right permissions are applied (but read on to learn about ownership requirements above the directory in question).
So there are a few key things here that cause Apache not to follow symlinks:........
cat .htaccess
RewriteEngine On
RewriteCond %{REQUEST_FILENAME} !-f
RewriteCond %{REQUEST_FILENAME} !-d
RewriteRule . index.php [L]
I keep reading there is a "# BEGIN WordPress" and a "# END WordPress" in the wordpress htaccess above but there is clearly not.
Even more strange is that my permissions are just 444 (read only).
so i changed it........
It is really simple using .htaccess with mod_rewrite.
Here is all you need:
RewriteCond %{SERVER_PORT} 80
RewriteRule ^(.*)$ https://site.com/$1 [R=301,L]
Another more graceful way is to use the %{SERVER_NAME}variable to make it dynamic. Just be careful that the server name will always match what you expect. (eg. if you are doing load balancing or clustering what if the server name may be somethi........
SSH helps keep us secure in many ways, one of those is the host-key fingerprint which is unique. If you have been connecting to an SSH server that you've made no changes to and suddenly ssh warns that the key doesn't match then you have a problem.
But how about connecting to an existing server for the first time on a new machine or client?
A lot of new clients calculate it using an SHA256 hash but it is not as easy on your host machine to produce the sam........
The net-tools command brings back all of the oldschool tools that we're used to:
/bin/netstat
/sbin/ifconfig
/sbin/ipmaddr
/sbin/iptunnel
/sbin/mii-tool
/sbin/nameif
/sbin/plipconfig
/sbin/rarp........
Before getting into the output here is my typical experience with SMART, there is what I call a "bad disk" with pending and uncorrectable sectors that cannot be reallocated.
It has caused a kernel panic and system crash repeatedly as we can see from the logs.
But SMART says it has "PASSED" its self assessment. SMART is still useful to me but it is more about looking at Current_Pending_Sector.
Any time I have had anything but 0 for that attribute it........
#to show all
VBoxManage list vms
#show ONLY running vms
VBoxManage list runningvms
VBoxManage storageattach test --storagectl "SATA" --port 0 --device 0 --type hdd --medium iscsi --server 192.168.1.91 --target "iqn.2018-12.local.abcrandom.target:sdb" --initiator "iqn.1982-01.ca.bla.tld:abc123" --t........
# a single first slash means first occurrence
# format=${haystack/needle/replacement}
# if you use a double first slash it means ALL occurrences
# format=${haystack//needle/replacement}
email=${file/.txt-marked/}
In the example above we are searching in the variable $file for ".txt-marked" and replacing with nothing (the empty part after the last / means we are replacing with n........
systemd is like the service manager for your Centos and other modern Linux distributions (including Debian/Mint/Ubuntu) allows you to enable services, stop them, restart them, check their status and even reboot your system.
The key commands or arguments you will use with systemctl are the following:
Unit Commands:
list-units [PATTERN...] List loaded units
&nbs........
sudo apt-get install libcurl4-openssl-dev git build-essential autotools-dev autoconf libcurl3
sudo apt-get install libcurl4-gnutls-dev
git clone https://github.com/wolf9466/cpuminer-multi
sudo apt-get install cmake libpthread-* libmicrohttpd-dev libssl-dev libhwloc-dev
git clone https://github.com/fireice-uk/xmr-stak-cpu.git
make install
cd bin
chmod +x xmr-stak-cpu
./xmr-stak -O xmr........
You can search for this bug and it seems like it may be related to ecryptfs and is many years old.
The symptoms are that you return to the computer and the screensaver was active or the screen was asleep/black and it doesn't seem to come back. But you check by SSH the computer is running fine and are frustrated you'll lose your running programs and have to reboot.
There is a simple solution:
Ctrl + Alt + F1
Ctrl +Alt + F8
Ba........
The reason for this article is because a lot of us don't physically see our hard drives they are often remote in a datacenter etc and the actual serial number we see in SMART is not enough to check for some manufacturers.
A good example is our first one the Toshiba
=== START OF INFORMATION SECTION ===
Device Model: TOSHIBA DT01ACA200
Serial Number: 33FMDW4AS........
Internal Server Error
The server encountered an internal error or misconfiguration and was unable to complete your request.
Please contact the server administrator, root@localhost and inform them of the time the error occurred, and anything you might have done that may have caused the error.
More information about this error may be available in the server error log.
Apache/2.2.15 (CentOS) Server at testdomain.com Port 80........
This is one thing that has me wondering about SMF. It is apparently a known issue but in the latest version and new install nothing looked right because it was using http://127.0.0.1 to find everything! How on earth would it ever do this or think it is normal?
Excerpt of crazy html code it produces that causes the issue:
........
So I have a domain "testdomain.com".
Inside test domain.com's root is the following .htaccess:
Options +FollowSymLinks -Indexes
ErrorDocument 403 /launch/index.html
Order Deny,Allow
Deny From All
Allow From 192.168.1.2
When you visit anything other than root things work fine. Eg. if you visit http://testdomain.com/somedirfile.html
It will show the right error in /launch/........
The easiest way is to use SSHand DD or a combination of netcat. SSHwill be a little slower due to encryption but is the most secure way (on two older systems the average clone speed is about 40-50MB/s). This is also OS independent as it doesn't matter what the source OS is because you are literallly cloning the drive so you retain the partition table and settings.
Clone HDD using SSH and DD........
order deny,allow
Deny From All
Allow From 8.8.8.8
A simple and quick way to improve security by only allowing specific IPs to your web application.
In this case the above allows only the IP 8.8.8.8 to access things and everything else is denied.........
PHP Warning: PHP Startup: Unable to load dynamic library '/usr/lib64/php/modules/geoip.so' - /usr/lib64/php/modules/geoip.so: undefined symbol: GeoIP_country_code_by_name_v6 in Unknown on line 0
Remove the GEOIP from PHP:
php71w-pecl-geoip-1.1.1-1.w6.x86_64
PHP Fatal error: PHP Startup: apc_shm_create: shmget(0, 67108864, 914) failed: Invalid argument. It is possible that the........
This just simply outputs what you need a username and password that can be used to authenticate from .htaccess
htpasswd -nb user password
user:Gnb6uE9Lp4gt2
If you want to write it straight to a file
htpasswd -cb /tmp/somefile.pw user password
How To Use This In .htaccess
AuthUserFile /tmp/somefile.pw
AuthName GetLost!!
AuthType B........
The code may lead you to believe you have an incompatible template but if you are not trying to use an old template currently that is not the issue. I actually deleted all 3.x style templates to make sure.
What the issue is, is old plugins that are not compatible but Vbulletin does not seem to account for this except that you'll see a fatal PHPerror. You should disable all plugins and then enable one by one until you find the one that is causing the issue.
&........
#if you have nvidia make sure you install the nvidia-cuda-toolkit so hardware acceleration can be used
wget http://ffmpeg.org/releases/ffmpeg-3.3.2.tar.bz2
tar -jxvf ffmpeg-3.3.2.tar.bz2
cd ffmpeg-3.3.2/
./configure --disable-yasm
install prefix /usr/local
source path ........
When running cudaminer once it tries to initialize the card the entire screen freezes. The computer itself is still running but the Xorg is done for, you cannot even switch to another console window and must reboot (even an mdm or Xorg restart does not help).
At first cudaminer will give you these errors:
stratrum_recv_line failed
...retry after 15 seconds
GPU #0: Geforce 210 with compute ca........
Jun 1 15:45:42 videoeditor-desktop org.mate.panel.applet.MintMenuAppletFactory[1882]: project_data:INFO Missing folder chosen by user:
Jun 1 15:45:42 videoeditor-desktop org.mate.panel.applet.MintMenuAppletFactory[1882]: project_data:INFO Removed missing file: MAH02949.MP4
Jun 1 15:45:57 videoeditor-desktop org.mate.panel.applet.MintMenuAppletFactory[1882]: ui_util:WARNING Icon theme media-playback-start not found. Will use backup........
This error is commonly due to Java security or TLS settings but there is a second issue with forwarded ports that also causes it.
1. Java Security/TLS Settings issue:
This article has the solution to change them all in Linux automatically
2. Port Forwarding Issue if your Avocent DSR is behind NAT/private IP........
This is especially helpful if you run your own servers. If you are presented with an error message or warning that the signature has changed or does not match the IP/domain you are connecting to you always want to verify manually.
So your e-mail/web client will show you an SHA-1 fingerprint like this:
"Could not verify this certificate because the issuer is unkown" or other reasons such as a mismatch in IP/domain.
It will also show you........
In short the two drives in the array were /dev/sdd and /dev/sde. The kernel sees they were unplugged and have gone down as you can see below.
mdadm caught the first one being unplugged /dev/sde and disabled the missing drive. However when the final drive that was part of the array is unplugged it didn't notice at all. Instead it complains about an IO error later for drives that the kernel knows do not exist anymore.
[45817.162728] ata4: exception........
Add this to the .htaccess file
#right/working:
AddType application/x-httpd-php .html .htm
#wrong (won't work in many cases):
AddHandler application/x-httpd-php5 .html .htm........
The only real way us to do the following in the root of your site's .htaccess
RewriteRule ^somedirectory-not-to-inherit/.*$ - [L]........
A friend has this issue where you try to go to contacts and you get a message saying you need to enable data (basically if you are not really on the AT&T network).
The Solution - You can disable this by the following code in the dialer:
*#*#2666#*#*........
Many users still are not aware but simply patching OpenSSL does not secure you against many known and easy to exploit attacks that will render your encryption useless by an attacker.
Use the following setings in /etc/httpd/conf.d/ssl.conf
SSLCipherSuite "EECDH+ECDSA+AESGCM EECDH+aRSA+AESGCM EECDH+ECDSA+SHA384 EECDH+ECDSA+SHA256 EECDH+aRSA+SHA384 EECDH+aRSA+SHA256 EECDH EDH+aRSA !CAMELLIA !SEED !3DES !RC4 !aNULL !eNULL !LOW !MD5 !EXP !PSK !........
The solution is simple but strange, if you copy your /var/lib/mysql directory to another server and think it will work, be sure to check if you have /var/log/mysql and binary log files. If you do, the server will not work and will give you errors like below and crash without the proper log files.
UPDATE user SET password=password("newpass") WHERE user='root';
flush privileges;
ERROR 2013 (HY000): Lost connection to MySQL server durin........
PHP Fatal error: PHP Startup: apc_shm_create: shmget(0, 67108864, 914) failed: Invalid argument. It is possible that the chosen SHM segment size is higher than the operation system allows. Linux has usually a default limit of 32MB per segment. in Unknown on line 0
PHP Fatal error: PHP Startup: apc_shm_attach: shmat failed: in Unknown on line 0
This error is not at all fun because it actually prevents Apache/httpd from starting or working at all. It will........
When installing Windows 2012 I cannot get around that error for some reason it just keeps on happening.
code:0xc0000005........
There was only one solution here and it was the following:
edit /etc/httpd/conf/httpd.conf
Comment the lines for the Mime Magic Module:
# MIMEMagicFile /usr/share/magic.mime
# MIMEMagicFile conf/magic
*Don't forget to restart Apache and clear your browser cache twice
I was using DefaultType and ForceType a........
When you start uploading larger images in Wordpress you have to make sure your maximum attachment size is large enough and that the execution time is not too short:
Uploading
Error
HTTP error.
[Thu May 12 16:32:25 2016] [error] [client 10.10.5.2] PHP Fatal error: Maximum execution time of 30 seconds exceeded in /httpdocs/blog/wp-includes/class-wp-image-editor-gd.php on line 182
Solution Edit p........
Does anyone have any suggestions on how to handle this error code? It is for a client who has a Windows 2008 R2 Datacenter License and wants to install virtual instances on the same host.........
cp -a /your/source/. /your/dest/
-a preserves all file atributes and symlinks
the "." at the end of /source/ includes all hidden files such as .htacess, .bash_history, .ssh etc..
The / in /dest/ makes sure the contents go into it instead of replacing /dest itself (eg. if you did not have the / at the end).........
There are a few ways of doing this and all basically involve using the reverse proxy or "ProxyPass" feature of Apache to accomplish it.
1.) Create a normal vhost and simply symlink the root directory of the site you want to mirror.
Eg. originalsite.com and newsite.com
/vhosts/originalsite.com/httpdocs
You would symlink like this:
ln -s /vhosts/originalsite.com/httpdocs vhosts/originalsite.com/........
The first thing to diagnose is what is actually in the database (use PHPMyAdmin or CLI).
You will of course either find that the backslash is either in the database or not.
If the backslash is in the database you probably have magic quotes gpc/runtime on and/or are calling the "addslashes()" function which does this.
If you are escaping your data with mysql_real_escape_string() then think again, you probably have magic quotes gpc enabled either in php.ini or........
The best way is as below in .htaccess using modrewrite, any request that is not SSL will be redirected to https://domain.com and the exact same URL
RewriteCond %{SERVER_PORT} 80
RewriteRule ^(.*)$ https://domain.com/$1 [R=301,L]........
It is just the readlink command with the -f switch and it will display the full path, very handy to save time when you want to copy and paste the location of a file or script etc..
readlink -f updatehtaccess.sh
/var/lib/updatehtaccess.sh
........
#solution
Edit /etc/yum.repos.d/openvz.repo
For the first two entries comment out #mirrorlist and uncomment #baseurl and then it worked
openvz yum problem Centos 6.5 cannot find file on mirror:
yum update
Loaded plugins: fastestmirror
Determining fastest mirrors
* openvz-kernel-rhel6: mirrors.ustc.edu.cn
* openvz-utils: mirrors.ustc.edu.cn
base ........
sudo apt-get install zoneminder
[sudo] password for one:
Reading package lists... Done
Building dependency tree
Reading state information... Done
The following packages were automatically installed and are no longer required:
libuser-perl python-evince kdebase-apps kwrite unixodbc
libgnomeprint2.2-data python-soappy vgabios python-metacity hddtemp
python-mediaprof........
I never did get it working, it is too bad as obfsproxy should really be an option and integrated into the OpenVPN client and server or something similar:
yum -y install python-pip python-devel
No package python-pip available.
#install the EPEL repo
python-pip install obfsproxy
python-pip install obfsproxy
-bash: python-pip: command not found
pip install obfsproxy
&........
This example is based on Wordpress but applies to any other query string eg.
http://wordpress.com/?p=55
If you want to manually redirect that p=55 to /some/other/url how do you do it?
RewriteCond %{QUERY_STRING} p=55 [NC]
RewriteRule .* /new-url/? [R=301,L]
You can change the p=55 to whatever your query string looks like.
Remember to keep the "?" at the end of the new URLunless you really want the query s........
I struggled with this for awhile because sometimes you have rewritten URLs that you want to pass a query string but most of the info and examples do not support this.
Take a typical example like this:
RewriteRule ^(.*)-(.*)-(.*) /?module=$3&id=$2
You need to add the QSA flag to make it work like below:
RewriteRule ^(.*)-(.*)-(.*) /?module=$3&id=$2 [QSA]
The QSA preserves the original query string but also appends it wit........
drbd 8.3 hard drive failure recovery
drbdadm attach r0
DRBD module version: 8.3.10
userland version: 8.3.8
you should upgrade your drbd tools!
0: Failure: (119) No valid meta-data signature found.
==> Use 'drbdadm create-md res' to initialize meta-data area. ........
To activate your Windows server trial which gives you 180 days:
Start ->Right Click (My Computer).
Click "Activate Windows now"
To renew your license for 180 days (can be done 6 times):
Start -> Type this command:
slmgr.vbs -rearm
Wait a few minutes until it says it is successful (unless you get that message it has not worked or been done)........
[3805108.257042] sd 0:0:0:0: [sda] 1953525168 512-byte hardware sectors: (1.00 TB/931 GiB)
[3805108.257052] sd 0:0:0:0: [sda] Write Protect is off
[3805108.257054] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[3805108.257066] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[3805108.257083] sd 0:0:0:0: [sda] 1953525168 512-byte hardware sectors: (1.00 TB/931 GiB)
[3805108.257090] sd 0:0:0:0: [sda] Write Protect is off........
Add this to a new ".htaccess" file inside the directory where the .html resides:
AddType application/x-httpd-php .php .html........
yum -y install fail2ban
vi /etc/fail2ban/jail.conf
[asterisk-tcp]
enabled = true
filter = asterisk
action = iptables-multiport[name=asterisk-tcp, port="5060,5061", protocol=tcp]
sendmail-whois[name=Asterisk, dest=you@example.com, sender=fail2ban@example.com]
logpath = /var/log/asterisk/messages
maxret........
order deny,allow
deny from all
allow from your.ip.here
........
tar -czf yourfile.tar.gz .
The . dot is the crucial part, normally many will use * and that will exclude hidden files by default which is very undesirable as many hidden files are important such as .htaccess and conf files in your home directory etc.. It seems the default behavior of tar should be the opposite but these are all very old tools.........
Add this to htaccess:
Options +Indexes
After that people will be able to browse files and directories of your site.........
Istruggled with this for awhile because the normal setup won't work if modrewrite is being used:
ORDER ALLOW, DENY
So the solution is something like this:
order allow,deny
deny from 12.43.12.0/24
allow from all
........
htpasswd -b -c filename username "password"
-b = take the password that we specify in the command (don't prompt for it)
-c = create the filename
username=username
password=password (I use quotes because it breaks if you use special characters)........
The results are not bad, the Hitachi performs the same as it does in a SATA2 motherboard. However, the 2TB is much different, on a similar 2TB Toshiba I get about 198MB/s on a different motherboard vs the 2TB Hitachi which should produce similar results.
This Dell Perc 6/i is on a PCI x8 riser card and is connected to a 12-port backplane.
Adapter #0
Enclosure Device ID: 32
Slot Number: 0
Enclosure position: N/A
De........
One thing to remember is that you need MegaCli to do the flashing.
You also need the correct file,I tried at least 2 different Perc 6 firmwares from Dell that kept getting rejected as corrupt by MegaCli(they were really the wrong version). I have an external PCI-E Dell 6 Perc/I butI chose images from the 'Integrated" on motherboard version as it was allI could find. They are different, and below is my first time finding success.........
I flashed an LSI Logic firmware to it and it broke the BIOS (cannot do Ctrl+R) for booting purposes but allows other functionality to work normally.
I tried downgrading to a Dell firmware for Perc 6i but it won't work, not even with MegaCli
wget http://downloads.dell.com/FOLDER00416606M/1/SAS-RAID_Firmware_W83M2_LN32_6.3.1-0003_A14.BIN
--2013-08-26 12:53:39-- http://downloads.dell.com/FOLDER00416606M/1/SAS-RAID_Firmware_W83M2_LN32_6.3.1-0003_A14.BIN
Resolvi........
The Cause
Basically it's usually because your Cpanel has new IPs and the old IPs it knows are no longer available/working/valid.
The solution is to change the site's IP but you may run into issues for various reasons. Here is what I encountered below.
It redirects there even though public_html is empty and doesn't have any index or htaccess redirect.
---
This issue happened after a CPanel migration, the site is bein........
The key here is to use the "uuencode" command but note that we specify the file name twice (this must be done at least on Centos or it won\'t work).
The first file.zip is the actual file we want to send.
The second file.zip i........
Once I set a new MAC address everything was fine and finally anything can be pinged etc.., I've had this happen with many clients in different datacenters on different hardware.........
I chose this because I heard a lot of stories about scams and that many providers I contacted said they can't unlock the Canadian I717s (one said "my Bell server" is down).
This method worked perfectly on my Bell I717M and should work for all I717 in Canada, I was able to insert a foreign SIMcard. This will work abroad too but remember entering CWM mode is different for I717's in other countries (at least theUS).
Step 1 - Root + CWM........
Here's a proven example of what a bad hard drive can do, it was technically functioning OKin a RAID array but the system became extremely low and the load become high and IOWAIT was even higher and I always thought it was a bad application. The truth is that this failing 1TBHitachi has slowly gotten worse and caused huge slowdowns, (eg. 100% load on Thunderbird waiting for e-mails to load etc..). After swapping it out, tabs change instantly, emails are not lagged, and........
Here's what SMART tells me the serial number is:
=== START OF INFORMATION SECTION ===
Device Model: Hitachi HDS721010CLA332
Serial Number: JP2940HQ3ZY7KH
Firmware Version: JP4OA3EA
User Capacity: 1,000,204,886,016 bytes
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 8
ATA Standard is:&nb........
Let's keep this simple, it's horrible, not only is the picture quality horrible (it's not a big deal) but the keyboard input is an issue. You have to type slowly, lightly and carefully otherwise 1-keystroke could end up being dozens of keystrokes.
It's also a confusing unit for many datacenter techs, I've seen these units hooked up wrong and the instructions themselves aren't clear. I had to resort to shipping one to my office and take my phone pictures of the setup for th........
I've run into two issues with Lantronix based KVMs on various servers and here's how I solved them (with that said I like these units as they are Java based and OS independent and work very well, unike some other models like Startech).
1.) If you are connected by USB only and you're sure USB support from the BIOS is enabled, you just need to click the following in Lantronix
Interfaces -> Keyboard/Mouse
Check "Force USB Full Speed Mode", this fixed the issu........
This is something I often setup for clients because it's very helpful for people in datacenters, this allows custom OS installs on demand, you can customize it more by using kickstart etc.. but here's a base I use before customizing more:
This little script below will install everything you need to get booting by PXE Linux.
It also assumes you set a local IP (be sure not to overwrite your existing IP) on eth0:0 (note the :0) as 192.168.1.10 and it........
A lot of people become nervous (and understandably so) when checking their auth or security logs, in Centos /var/log/secure and see dozens, hundreds of even thousands of attempted logins to various services, especially SSH.
Of course you could manually block these people/IPs but no one has time to read the logs like that, what if some program or script could do it for you?
This is what denyhosts does for you, it checks the logs and based on a certain number of failed SSH attem........
I searched for days after getting my Galaxy Note and couldn't find a way to do this (at least not without buying programs for either Android/Windows). All I read was ways to sync and import the contacts to GMail but I don't want to use GMail for privacy reasons. GMail/Google steal all of your personal information and use it for whatever purposes they want to and may sell or release it to who knows where (I don't care what their policy says but this stuff happens), just like the default........
I dread updating the kernel and rebooting to find the Ubuntu graphics aren't working and you have to manually intervene. This is usually because Ubuntu for whatever reason didn't update the drivers you need (eg. the manually compiled Nvidia Kernel driver that MUST be recompiled for each and every kernel update unfortunately).
The most common reason may be that "linux-source" hasn't been installed automatically on my system. I tried to manually reinstall the........
*Make sure that the ownership is 501.501 or mobile.mobile when copying back (especially if using ssh or sftp as root on the iPhone) otherwise things will break. Eg. the contacts will be blank even after trying to update due to incorrect ownership/permissions.
iPhone Notes Location/Restore:
/private/var/mobile/Library/AddressBook
AddressBookImages.sqlitedb AddressBook.sqlitedb
Once you restore the contacts and restar........
The first Hitachi Deskstar 2TB 5K3000 drive I bought arrived DOA for whatever reason (not recognized by the BIOS or OS). Perhaps it was shipping since I bought only 1 hard drive. When I bought 4 through another Vendor, all 4 checked out fine.
I was worried about the RMA process because a lot of people have complained about Hitachi taking weeks to send out their hard drive and almost implied the warranty is useless.
I'm happy to report that my experience was great a........
ifup eth0
SIOCSIFFLAGS: Cannot allocate memory
Failed to bring up eth0
This is on a Centos 5.5 machine with OpenVZ kernel 2.6.18-238.12.1.el5.028stab091.1PAE, I updated 3 systems with the same hardware to the same kernel and for some reason the network didn't come back.
This only happened once the first time I booted into the new kernel and hasn't happened again but this is a serious issue for those running systems from remote locations such as a datacente........
I like dd, although it only reads it, usually a read test of the entire disk will uncover if your hard drive is bad in some parts. This is a good thing to do at least once a month, a lot of times bizarre program behavior, laginess and crashing/unnmounting problems etc.. are due to a failing disc and SMART won't know it or indicate a problem:
We must also remember there's never a guarantee, I've found that ever since we moved to larger and more platters per drive with 1TB drives........
It's weird because I have a nearly identical box and setup and I can update the ovzkernel-PAE* just fine but on this box it doesn't work.
I only get this error with the openvz.repo and not others such as Centos-Base.repo
With my other server it works normally:
================
Setting up Update Process
Resolving Dependencies
--> Running transaction check
---> Package ovzkernel-PAE.i686 0:2.6.18-238.12.1.el5.0........
I had one of these shipped and it was not recognized when plugged in, here's what a dead drive looks like (I assume it's teh circuit board which is dead):
ata1: link is slow to respond, please be patient (ready=0)
ata1: softreset failed (device not ready)
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1: link online but device misclassified, retrying
ata1: link is slow to respond, please be patient (ready=0)
ata1: softreset f........
This assumes that you've at least created the correct partition for your DRBD already.
Notice that I am "diskless", that's because either your DRBD partition doesn't exist/has been renamed (eg. sdb becomes sda when sdb dies and you reboot) or because that drive is really actually dead/gone.
*If you need to permanently change the partition/device for your resource be sure to edit /etc/drbd.conf on both hosts and reload the config.
(replace r0 with........
May 6 08:16:57 devbox spamc[16225]: connect to spamd on 127.0.0.1 failed, retrying (#2 of 3): Connection timed out
May 6 08:17:02 devbox spamc[20214]: connect to spamd on 127.0.0.1 failed, retrying (#1 of 3): Connection timed out
spamc[16225]: connect to spamd on 127.0.0.1 failed, retrying (#3 of 3): Connection timed out
First make sure that the spamd service is actually running, this is your spamd (spamassassin server) cannot be reached. In my c........
mod_status is a great way to track down the source of high CPU usage and to find what vhost/script is the cause of it.
It gives you a live view of bandwith usage, CPU usage, and memory usage broken down by domain/vhost and script/URI.
Enable mod_status
vi /etc/httpd/conf/httpd.conf
ExtendedStatus On
SetHandler server-status
Order Deny,Allow
Deny from all
All........
I was getting frustrated with trying to write a simple URL like this:
/example-withdash
I used the htaccess code like this:
Rewriterule ^example-withdash$ / [R=301]
I also tried escaping the dash which I thought should have treated it as a literal but that didn't work either:
Rewriterule ^example-withdash$ / [R=301]
But it wouldn't work, apparently the "-" dash means don't substitute,........
I was afraid to remove the virtualbox 3.2 package in Ubuntu because I didn't know if it might remove the .virtualbox folder which contains all of my VM data.
I have a backup soI did remove the package and found everything was intact, so I installed and upgrade to VBOX 4.0 which seems to be a huge improvement, especially in UI performance.........
drup 6.2 install
$cd drupgoodinst3883/
[ drupgoodinst3883]$ ls
CHANGELOG.txt cron.php index.php INSTALL.pgsql.txt INSTALL.txt MAINTAINERS.txt modules robots.txt sites update.php xmlrpc.php
COPYRIGHT.txt includes INSTALL.mysql.txt install.php LICENSE.txt misc&........
I don't expect this to be solved soon but some of Yahoo's DNS servers are out of whack. I changed the IPs of some nameservers of some domains and now most Yahoo users can't e-mail to those domains!
As you can see below by the "No MX or A records for mychangedomain.com", now Yahoo's DNS/mailserver DNS cache is wrong. You would think they would at least have cached the old incorrect records, but instead for some reason their DNS cache has no entry and doesn't seem........
high IO wait
424 root 39 19 1900 848 552 D 0.0 0.0 0:00.91 updatedb
root 424 0.0 0.0 1900 848 ? DN Mar11 0:00 /usr/bin/updatedb -f sysfs?rootfs?bdev?proc?cpuset?binfmt_misc?debugfs?sockfs?usbfs?pipefs?anon_inodefs?futexfs?tmpfs?inotifyfs?eventp........
I bought the 1TB Deskstar C revision recently at just $49 each and put them in RAID 1for my Desktop.
Look at how close the old Deskstar 1TB comes to matching the performance of the mor expensive Samsung and WD's?
This is phenomal, I can't believe the performance I've gotten out of these cheap drives.
http://www.tomshardware.com/reviews/hitachi-western-digital-terabyte,2017-6.html........
Forbidden
You don't have permission to access / on this server.
[Sun Jan 23 15:28:12 2011] [crit] [client 96.44.31.12] (13)Permission denied: /www/vhosts/domain.com/httpdocs/.htaccess pcfg_openfile: unable to check htaccess file, ensure it is readable
Solution
I've done a chmod 755 .htaccess and index.php and restarted Apache
That wasn't the only issue, the issue was the httpdocs direc........
tar include hidden files such as .htaccess
just add . to the path eg.
tar -czvf tarfile.tar.gz /home/directory/.........
CPU/Kernel/MB/RAID problem?
Jan 5 12:45:05 testbox kernel: [653298.890004] BUG: soft lockup - CPU#0 stuck for 61s! [hal-acl-tool:4168]
Jan 5 12:45:05 testbox kernel: [653298.890005] Modules linked in: vmnet vmci vmmon binfmt_misc drbd video output input_polldev ocfs2_stackglue ocfs2_dlmfs ocfs2_dlm ocfs2_nodemanager configfs k8temp hwmon_vid lp snd_hda_intel snd_pcm_oss snd_mixer_oss snd_pcm snd_seq_dummy snd_seq_oss snd_seq_midi snd_rawmidi........
Webmin Setup Centos 5:
wget http://downloads.sourceforge.net/project/webadmin/webmin/1.530/webmin-1.530-1.noarch.rpm?r=http%3A%2F%2Fwww.webmin.com%2Fstandard.html&ts=1294339690&use_mirror=surfnet
[1] 24229
[2] 24230
[root@host ~]# --2011-01-06 21:48:20-- http://downloads.sourceforge.net/project/webadmin/webmin/1.530/webmin-1.530-1.noarch.rpm?r=http%3A%2F%2Fwww.webmin.com%2Fstandard.html
Resolving downloads.sourceforge.net... 216.34.181.........
This made me nervous but it's clearly a cronjob based on the messages log that happens every Sunday at about 4:22.
I actually can't find any evidence of it in cron.d cron.daily but it is there somewhere obviously.
What I don't get is why doesn't this cronjob do a datacheck like Ubuntu's cronscript does? When you unnecessarily rebuild the array you lose your redundancy during that point which makes your data extremely vulnerable.
*Update I did a grep of &q........
Let the numbers speak for themselves, from what I read the Load_Cycle_Count which is very high (more than 500,000/half a million times) is the number of head parks. What a stupid"Green" design and design flaw which will probably mean an early life for the drive.
This is almost as silly as Seagate's new reputation for BSY/poor quality disks since the 7200.11 series.
To make it worse this is also when Western Digital introduced "Advanced Format" o........
I couldn't figure out why this wouldn't work, a test script in the root of my htdocs folder worked fine.
Within some subdirectories the same code would produce different base64 results but I didn't know hwy.
Archive: /tmp/archive.zip
Zip file size: 6888 bytes, number of entries: 92
error [/tmp/archive.zip]: missing 242827681 bytes in zipfile
(attempting to process anyway)
error [/tmp/archive.zip]: attempt........
This has stumped me a few times because I keep forgetting that Centos 5.5 comes with a default iptables configuration that ends up blocking DRBD traffic,I tried all the normal things and couldn't understand why I couldn't make my normal DRBD config work. So if you have WFConnection problems and have tried the normal "mailing list" fixes, check your firewall status first!
Both Nodes Say the Following:
version: 8.3.8 (api:88/prot........
This is a great way to use your ftp server space, for example on your web hosting account (althoughI believe many hosts don't allow storage like this), but if you have a VPS/Dedicated Server etc.., this would be perfect. Imagine how easy it is to work with an ftp account that you can just mount as a normal partition or directory in Linux, it would be great for backups etc..
Name
curlftpfs - mount a ftp host as a local directory
Synopsis........
Apr 30 17:07:07 localhost kernel: [12265558.582378] r8169: eth0: link up
Apr 30 17:07:07 localhost NetworkManager: (eth0): carrier now ON (device state 1)
Apr 30 17:07:08 localhost kernel: [12265559.237961] r8169: eth0: link down
Apr 30 17:07:08 localhost NetworkManager: (eth0): carrier now OFF (device state 1)
Apr 30 17:07:11 localhost NetworkManager: (eth0): carrier now ON (device state 1)
Apr........
I have no idea why but mkfs.ext3 defaults to a patheticlly small blocksize of 1024 bytes/1KB (kilobyte). That means the maximum filesize is ONLY 16GB! With 2KB/2048 bytes you get a 256 GB maximum filesize, and with 4KB/4096 bytes you get 2TB!
I finally noticed/paid attention to this after realizing that with rsync and scp that no file larger than 17GB could be transferred. I then realized it must be a file size limit on the partition.
Here is what tune2fs tol........
It's basically free bash shell script available from: http://wpkg.org/email2fax/index.php/Main_Page
Make sure you have the required tools:
libtiff
ghostscript
mpack/munpack
Where you can e-mail your Asterisk box and it will fax it to the phone number in the subject line. The good news ends there, it is fairly undocumented and buggy.
Take for example how the documentation mentions you can invoke from the com........
I decided on using yum to help me decide even though I normaly use proftpd I decided to see what else I could find.
yum search ftp
Loaded plugins: fastestmirror
Loading mirror speeds from cached hostfile
* rpmforge: ftp-stud.fht-esslingen.de
* base: mirrors.netdna.com
* updates: updates.interworx.info
* addons: yum.singlehop.com
* extras: mirrors.netdna.com
rpmforge........
PHP cannot access /usr/bin/opensslI have verified the username that runs the process is able to access /usr/bin/openssl and it does exist but the PHP script is saying it doesn't exist:
[code:1:1fd0f3abbe]
if (!file_exists($OPENSSL)) {
//echo "ERROR: OPENSSL $OPENSSL not foundn";
}[/code:1:1fd0f3abbe]
I don't get itI can clearly see the contents of /usr/bin by using the PHP system fu........
SSH automatic login without passwordlocal> ssh-keygen -t rsa -f .ssh/id_rsa
-t is the encryption type
-f tells where to store the public/private key pairs. In this case, the .ssh directory on home is being used
A password will be asked; leave this part blank, just pressing
Now, go the .ssh directory, and you will find two new files: id_dsa and id_dsa.pub. The last one is the public part. Now, copy the public key to the serv........
Centos 4.3 x64 & VMWare Server Beta[code:1:6d0b2c8c2f]
The correct version of one or more libraries needed to run VMware Server may be
missing. This is the output of ldd /usr/bin/vmware:
linux-gate.so.1 => (0xffffe000)
libm.so.6 => /lib/tls/libm.so.6 (0xf7fbd000)
libdl.so.2 => /lib/libdl.so.2 (0xf7fb9000)
libpthread.so.0 => /lib/tls/libpthread.so.0 (0xf7fa7000)
libX11.so.6 => not f........
Telus + 2Wire 2700 Router HorribleWell first of all let me say this is the only router/switch that sometimes seems to crash/disconnect computers on the local network.
This device also thought it would be smart to block VOIP packets coming from my Sipura ATA VOIP adapters so I disabled the [quote:cb89ba7bff]"Invalid TCP Flag Attacks (NULL/XMAS/Other)"[/quote:cb89ba7bff] option
Then all of a sudden I couldn't get onto any web pages, the wireless........
Intruder detection device uses behavioural analysisIntruder detection device uses behavioural analysis
by Antony Savvas
Monday 13 June 2005
Symantec is introducing a new intrusion detection product that uses behavioural analysis to block potential attacks on enterprise networks.
The new Critical System Protection 4.5 system uses technology that Symantec acquired through last year’s purchase of Platform Logic. It is designed to protect deskt........
Comment lines in #htaccessYou can create a hash '#' at the beginning of the line:
eg:
[quote:2d67449f2c]#[/quote:2d67449f2c]........
Put what you see below into your .htaccessand it will enable errors and notices. (change on to off and 1 to 0 to disable though)
php_flag display_startup_errors on
php_flag display_errors on
php_flag html_errors on
Now you'll be able to see errors and notices but this should really only be used for debugging purposes and only temporarily as it can be a security issue since errors can reveal information you wouldn't want hacker........
RemoveHandler .html .htmAddType application/x-httpd-php .php .htm .html Just add the above into the .htaccess file for your website. Also remember that you need to be allowed to override the Apache and this should go into the vhost for your site as shown below:
# you need the AllowOverride otherwise .htaccess directives will be ignoredOptions FollowSymLinksAllowO........
This is something that happens a lot and it is very dirty, as you probably know each site is hosted on a certain IP address. Sometimes a domain is hosted by a single IP address and the IP address defaults to this very same domain.
This means that if someone buys domain abcd.com and enters your IP address (the one of your website) as the A record, your content will show up on their domain as if it was their own.
There is an easy way to prevent this by using .htacces........
Itried everything Icould think of, and of course even with the NIC enabled in the BIOS nothing was working. The light would flash when you plugin the cable for a second, but that's all.
Due to another issue I'm about to post about (server is not compatible with 1TB/1000Gig Hard Drives), I updated the BIOS. I didn't even know the 100mbit NICs were not working untilI decided I should test each NIC one by one.
Inoticed that only 1 server out of........
I was getting very frustrated one day wondering why it appeared my .htaccess file was being ignored and not processed by Apache. No matter what I did it was obvious that Apache didn't care about my .htaccess file. Then I realized that the default settings must be in effect, which is that my vhost didn't explicitly allow me to override the default settings.
This usually comes down to your vhost settings. Make sure you have an entry like this in your Apache vhost settings in........
When trying to even cd or ls the mounted OCFS2 partition it crashes. Ithink this is a combination of VMWare Server's problem and the way I mounted and symlinked to it.
More than anything this shows the problem and lack of forsight with VMWare, but also that OCFS2 is easily crashed if you do strange things.
Output of /var/log/messages for OCFS2
Apr 10 15:57:45 localhost kernel: [84331.691258] Modules linked in: vmnet vmci vmmon ocfs2_stac........
There's a lot of information and guides on OCFS2 for RHELand Centos Linux but the package setup and configuration is slightly different and this has thrown some people off.
Installing OC2FS
You should install the following packages to get started:
apt-get install ocfs2-tools ocfs2console
Configure OC2FS
In RHEL/Centos the main configuration file is located in /etc/sysconfig/o2cb
However in Debian based Linux it is located........