/ - rtt - IT Resource

  • systemd management using systemctl and journalctl to check systemd logs


    systemd is like the service manager for your Centos and other modern Linux distributions (including Debian/Mint/Ubuntu) allows you to enable services, stop them, restart them, check their status and even reboot your system. The key commands or arguments you will use with systemctl are the following: Unit Commands:   list-units [PATTERN...]         List loaded units &nbs........
  • Centos 7 - How To Install NFS and Mount Remotely


    1.) First install nfs-utils [root@bcitcourse ~]# yum -y install nfs-utils Loaded plugins: fastestmirror base                                                         &n........
  • How to qemu-kvm enable bridged networking in Debian Ubuntu Linux Mint on KVM containers


    I've read a few guides about this but they didn't work for me. sudo apt-get install bridge-utils #don't think the above is enough it won't work still even though you have by default an /etc/qemu-ifup that handles it if you have the right tools and setup sudo qemu-system-x86_64 -net tap -net nic -enable-kvm -cpu host,vmx=on ~/VirtualBox VMs/vsphere-vcenter/vsphere-vcenter.vdi W: /etc/qemu-ifup: no bridge for guest interface foun........
  • NFS Share Won't Mount Solution - mount: wrong fs type, bad option, bad superblock on 10.10.2.20:/tmp/nfsmount


    nfs mount failed: mount 10.10.2.20:/tmp/nfsmount /mnt/nfs/ mount: wrong fs type, bad option, bad superblock on 10.10.2.20:/tmp/nfsmount,        missing codepage or helper program, or other error        (for several filesystems (e.g. nfs, cifs) you might        need a /sbin/mount.<type> helper program)       ........
  • Linux Mint Black Screen after boot no graphics solution


    This is not the normal "black screen" issue and I was shocked to eventually find out why.  The normal advice of reconfiguring Xorg didn't work.  Even booting into "Recovery Mode" did not help. Here is the short end of the stick that fixed it: sudo apt-get install mdm mate-desktop-environment Yes you got it right, mdm and the mate-desktop-environment / gnome were somehow uninstalled.  This must be whe........
  • Install Windows From a Linux TFTP Server instead of using WDS Solution


    yum -y install samba vi /etc/samba/smb.conf https://www.kernel.org/pub/linux/utils/boot/syslinux/syslinux-6.03.zip mkdir syslinux;cd syslinux;unzip syslinux-6.03.zip mkdir -p /tftpboot/libs/ cp bios/com32/modules/linux.c32 /tftpboot/libs/ cp bios/com32/libutil/libutil.c32 /tftpboot/libs/ cp bios/com32/lib/libcom32.c32 /tftpboot/libs/ #add lib path echo "PATH libs" >> /tftpboot/pxeli........
  • pcimodules and lspci not working alternative solution


    pcimodules no longer works it produces nothing probably because the format of /sys/bus/pci is different. lspci -k doesn't work on older lspci versions. pciutils can be compiled but it won't work if you have an old system and compile on a newer glibc. iteriate through /sys/bus/pci/devices/*/modalias cat /sys/bus/pci/devices/*/modalias pci:v00008086d00001237sv00000000sd00000000bc06sc00i00 pci:v00008086d00007000sv0000000........
  • kdenlive titles/text renders as white screen when using .sh script


    When using the .sh script the rendering doesn't work after an upgrade of related packages to kdenlive.   kdenlive (kdenlive:amd64 (4:17.04.1+git201705191233~ubuntu16.04.1)) with affine or composite transitions was fine but is now broken during the time of transition it is just a white screen. The previous version was fine: kdenlive:amd64 (4:17.04.1+git201705191233~ubuntu16.04.1 But now I can't find it or install it:........
  • Wine uninstalled broken on Linux Mint


    Solution: Aptitude is very smart and fixed the issues it was because of nvidia cuda and opencl and nothing else suggested or hinted this using apt sudo aptitude install wine The following NEW packages will be installed:   ocl-icd-libopencl1{ab} ocl-icd-libopencl1:i386{ab} wine wine1.6   wine1.6-amd64{a} wine1.6-i386:i386{a} The following packages will be REMOVED:........
  • Linux Mint Install Netboot PXE Guide Howto


    *Update so this doesn't work it must be something to do with the path of nfs or something else but the installer fails with "Installer crashed" at the end whereas with the CD/USB it works. This assumes you've already installed and configured a separate PXE/DHCP server somewhere else and your /tftpboot directory is setup. This is for Linux Mint 18.1 but generally applies to most versions although you may have tro change things like "casper"........
  • PYCURL ERROR 22 - The requested URL returned error: 404 Not Found Solution


    # yum -y install qemu-kvm Loaded plugins: fastestmirror Setting up Install Process Loading mirror speeds from cached hostfile  * base: mirror.lzu.edu.cn  * elrepo: ftp.utexas.edu  * epel: ftp.jaist.ac.jp  * extras: mirrors.aliyun.com  * openvz-kernel-rhel6: mirror.fdcservers.net  * openvz-utils: mirror.fdcservers.net  * updates: mirrors.nwsuaf.edu.cn Resolving Dependencies........
  • Mount a SMB Samba share in fstab Linux Debian/Ubuntu/Centos


    Add the following to fstab where 192.168.1.125/Media is the samba share and where /home/homeuser/Downloads is where you want to mount. Change user and pass to what is needed (if no pass is required it still works fine with the below). //192.168.1.125/Media /home/homeuser/Downloads cifs        user=guest,pass=bla 0 0 mount: wrong fs type, bad option, bad superblock on //192.168.1.125/Media, &nbs........
  • openvz yum problem Centos 6.5 cannot find file on mirror:


    #solution Edit /etc/yum.repos.d/openvz.repo For the first two entries comment out #mirrorlist and uncomment #baseurl and then it worked openvz yum problem Centos 6.5 cannot find file on mirror: yum update Loaded plugins: fastestmirror Determining fastest mirrors  * openvz-kernel-rhel6: mirrors.ustc.edu.cn  * openvz-utils: mirrors.ustc.edu.cn base      ........
  • Cannot mount iPhone or iPad in Linux


    Unable to mount iPad 4 Unhandled Lockdown error (-4) This is because you need the libimobiledevice-utils package installed and a newer version of it. My older Ubuntu 10.10 uses a version that does not have "idevicepair" which seems to work perfectly and automatically with newer versions of the library. Basically if you install the above library it should be plug and play and if your imobiledevice-utils doesn't have 'idevice........
  • Dell Perc 6/i cannot downgrade


    I flashed an LSI Logic firmware to it and it broke the BIOS (cannot do Ctrl+R) for booting purposes but allows other functionality to work normally. I tried downgrading to a Dell firmware for Perc 6i but it won't work, not even with MegaCli wget http://downloads.dell.com/FOLDER00416606M/1/SAS-RAID_Firmware_W83M2_LN32_6.3.1-0003_A14.BIN --2013-08-26 12:53:39--  http://downloads.dell.com/FOLDER00416606M/1/SAS-RAID_Firmware_W83M2_LN32_6.3.1-0003_A14.BIN Resolvi........
  • LSI MegaRAID Adventures, Guide and HowTo


    LSi Megaraid At first it was configured as a RAID 0, then I deleted the Virtual Disk Group. I thought both drives would be shown and detected in Linux as sda and sdb but it actually shows nothing. To make them work you have to hit Ctrl+R before the system boots (when prompted) and create a Virtual Disk Group.  In my case I created each one as RAID 0 (with a single drive only) as I just wanted JBOD but there is no such option or default in these Dell Pe........
  • Directadmin error/** Found 7 pre-existing rpmdb problem(s), 'yum check' output follows: e2fsprogs-devel-1.41.12-3.el6.i686 has missing requires of e2fsprogs-libs = ('0', '1.41.12', '3.el6') e2fsprogs-devel-1.41.12-3.el6.i686 has missing requires of l


    Solution To The Following: yum -y install zlib-devel yum -y install e2fsprogs* *** Cannot find /usr/include/et/com_err.h.  (yum install libcom_err-devel) *** Installation didn't pass, halting install. Once requirements are met, run the following to continue the install:   cd /usr/local/directadmin/scripts   ./install.sh Common pre-install commands:  http://help.directadmin.com/it........
  • Centos how to upgrade from PHP 5.2 to 5.3 without downtime


    This may sound silly but there will be conflicts/issues with the default Centos repository so you have to use a third party like remi (I prefer not to do this but it's the only option unless you migrate your sites/data to another server or can stand some downtime-not an option IMHO on a production server). You may need to upgrade to PHP 5.3 to run Joomla or many other reasons. Your host needs to use PHP 5.2.4 or higher to run this version of Jo........
  • Installing Webmin & Enabling SSL


    Webmin Setup Centos 5: wget http://downloads.sourceforge.net/project/webadmin/webmin/1.530/webmin-1.530-1.noarch.rpm?r=http%3A%2F%2Fwww.webmin.com%2Fstandard.html&ts=1294339690&use_mirror=surfnet [1] 24229 [2] 24230 [root@host ~]# --2011-01-06 21:48:20--  http://downloads.sourceforge.net/project/webadmin/webmin/1.530/webmin-1.530-1.noarch.rpm?r=http%3A%2F%2Fwww.webmin.com%2Fstandard.html Resolving downloads.sourceforge.net... 216.34.181.........
  • Ubuntu/Debian DRBD 8.0 Setup Guide


    I've only used it on Centos, so I thought I'd make a quick Debian guide: Install the DRBD Package apt-get install drbd8-utils Reading package lists... Done Building dependency tree       Reading state information... Done The following packages were automatically installed and are no longer required:   libswfdec-0.8-0 Use 'apt-get autoremove' to remove them. The following........
  • yum in Centos 5/Xen halts and exits suddenly


    yum exits in the middle The problem is this VPS seems to be an OpenVZ template from HyperVM.  The only way to make it work was to disable i386 packages since this was an x64 kernel.  That shouldn't be necessary but it was the only way to make yum stop quitting after the first package or two.  I couldn't find any issue by checking the logs either. echo y|yum install vim-minimal telnet expect jwhois net-tools slocate iptables elinks gawk L........
  • jailkit for chroot ssh account security tutorial and fix for error


    This was done on Centos but I think it's easier on Debian machines, the paths that it is set to use are tailored towards Debian, so there is some fiddling that needs to be done on Centos. This is for chrooting ssh, but jailkit has other uses than just SSH jails but I won't cover them in this writeup. 1. Install jailkit yum install jailkit 2. Setup Jail Home mkdir /home/jail chown root:root /home/ja........
  • Linux Burn MP3 CD On the Fly using


    I finally decided to look into some utils that did this, and the first one I found is "mp3burn".  It is unbelievable simple and perfect. *2017-11 update and mp3burn is still available in standard repos such as Ubuntu 14/16 so this is a current and working project. Just install the package and it gets all required libraries to convert and then burn's on the fly.  And you won't believe how simple it is. I just want to a directory that had the MP3's I wanted t........
  • Use rcconf to edit startup/init.d/init scripts on Debian/Ubuntu based distributions


    I've never understood how to enable and disable services for different run levels in Debian based distros, it's just weird, annoying and doesn't make sense.  I much prefer chkconfig from RHEL. Just install the package called 'rcconf' and be done with it.  rcconf makes things easy for you. apt-get install rcconf Reading package lists... Done Building dependency tree        Reading state information... Done........
  • Picking an FTPD (vsftpd) Server in Linux Centos/Debian


    I decided on using yum to help me decide even though I normaly use proftpd I decided to see what else I could find. yum search ftp Loaded plugins: fastestmirror Loading mirror speeds from cached hostfile  * rpmforge: ftp-stud.fht-esslingen.de  * base: mirrors.netdna.com  * updates: updates.interworx.info  * addons: yum.singlehop.com  * extras: mirrors.netdna.com rpmforge   ........
  • Latest Articles

  • syntax error, unexpected T_SL in PHP Solution
  • grep regular expression match number range between specific numbers
  • bash how to print out lines of text within a range from the first occurrence
  • bash script how to to check LAN computers for open ports
  • MySQL Using mytop Debug Source of High IO and Slow Performance
  • How To Mathematically Convert and Calculate Binary Value To Decimal Value
  • systemd management using systemctl and journalctl to check systemd logs
  • css how to format code in the code tag
  • css br with extra blank line
  • What is /dev/pts and why do we need it in Linux?
  • Linux What is umask (user mask) for file and directory creation permissions and how to calculate umask and change the defaults
  • Linux Permissions and Groups Real Usecase for Group Access
  • Centos 7 python34 how to install the gi library
  • Centos 7 - Convert Minimal to Graphical GUI GNOME or KDE Desktop
  • AMD Set Fan Speed and Other Powerplay Memory/CPU Timings with a Linux script
  • Ethereum Mining Claymore Nanopool Error
  • genisoimage errors with long filenames and deep directory structures
  • Linux Kernel USB Export Errors
  • How to download gajim 0.16.9 XMPP/Jabber client so you can use OMEMO encryption
  • HP DL385 G7 Linux BIOS Update Flash