Linux - mptbase/MPT Fusion LSI Logic Error mptbase: ioc0: ERROR - didn't initialize properly! (-1)

kernel 2.6.27.54

Fusion MPT base driver 3.04.07
Copyright (c) 1999-2008 LSI Corporation
Fusion MPT SPI Host driver 3.04.07
mptbase: ioc0: Initiating bringup
mptbase: ioc0: WARNING - Unexpected doorbell active!
mptbase: ioc0: ERROR - Doorbell ACK timeout (count=4999), IntStatus=80000001!
mptbase: ioc0: ERROR - Diagnostic reset FAILED! (102h)
mptbase: ioc0: WARNING - NOT READY!
mptbase: ioc0: ERROR - didn't initialize properly! (-1)
mptspi: probe of 0000:01:04.0 failed with error -1
========
Fixed by using modprobe and not building modules into the kernel:


request_module: runaway loop modprobe net-pf-1
SCSI subsystem initialized
Fusion MPT base driver 3.04.07
Copyright (c) 1999-2008 LSI Corporation
Fusion MPT SPI Host driver 3.04.07
mptbase: ioc0: Initiating bringup
ioc0: LSI53C1030 B2: Capabilities={Initiator,Target}
scsi0 : ioc0: LSI53C1030 B2, FwRev=01032300h, Ports=1, MaxQ=255, IRQ=29
scsi 0:0:0:0: Direct-Access     SEAGATE  ST336607LW       DS09 PQ: 0 ANSI: 3
 target0:0:0: Beginning Domain Validation
 target0:0:0: Ending Domain Validation
 target0:0:0: FAST-160 WIDE SCSI 320.0 MB/s DT IU RTI WRFLOW PCOMP (6.25 ns, offset 63)
scsi 0:0:1:0: Direct-Access     SEAGATE  ST336607LW       DS09 PQ: 0 ANSI: 3
 target0:0:1: Beginning Domain Validation
 target0:0:1: Ending Domain Validation
 target0:0:1: FAST-160 WIDE SCSI 320.0 MB/s DT IU RTI WRFLOW PCOMP (6.25 ns, offset 63)
scsi 0:0:8:0: Direct-Access     SEAGATE  ST336607LW       0007 PQ: 0 ANSI: 3
 target0:0:8: Beginning Domain Validation
 target0:0:8: Ending Domain Validation
 target0:0:8: FAST-160 WIDE SCSI 320.0 MB/s DT IU RTI WRFLOW PCOMP (6.25 ns, offset 63)

 


Tags:

linux, mptbase, mpt, fusion, lsi, logic, ioc, didn, initialize, kernel, copyright, corporation, spi, initiating, bringup, doorbell, active, ack, timeout, intstatus, diagnostic, reset, mptspi, probe, modprobe, modules, request_module, runaway, pf, scsi, subsystem, initialized, capabilities, initiator, fwrev, ports, maxq, irq, seagate, lw, ds, pq, ansi, domain, validation, mb, dt, iu, rti, wrflow, pcomp, ns, offset,

Latest Articles

  • FreePBX 17 How To Add a Trunk
  • Docker Container Onboot Policy - How to make sure a container is always running
  • FreePBX 17 How To Add Phones / Extensions and Register
  • Warning: The driver descriptor says the physical block size is 2048 bytes, but Linux says it is 512 bytes. solution
  • Cisco How To Use a Third Party SIP Phone (eg. Avaya, 3CX)
  • Cisco Unified Communication Manager (CUCM) - How To Add Phones
  • pptp / pptpd not working in DD-WRT iptables / router
  • systemd-journald high memory usage solution
  • How to Install FreePBX 17 in Linux Debian Ubuntu Mint Guide
  • How To Install Cisco's CUCM (Cisco Unified Communication Manager) 12 Guide
  • Linux Ubuntu Redhat How To Extract Images from PDF
  • Linux and Windows Dual Boot Issue NIC Won't work After Booting Windows
  • Cisco CME How To Enable ACD hunt groups
  • How to install gns3 on Linux Ubuntu Mint
  • How to convert audio for Asterisk .wav format
  • Using Cisco CME Router with Asterisk as a dial-peer
  • Cisco CME How To Configure SIP Trunk VOIP
  • Virtualbox host Only Network Error Failed to save host network interface parameter - Cannot change gateway IP of host only network
  • Cisco CME and C7200 Router Testing and Learning Environment on Ubuntu 20+ Setup Tutorial Guide
  • Abusive IP ranges blacklist