This guide assumes you have a working Postfix server and want it to sign with DKIM. There are a few things we have to understand to make all of this work though, which require you to be familiar with DNS as well. 1.) Install OpenDKIM apt install opendkim systemctl enable opendkim 2.) Edit /etc/opendkim.conf Syslog yes SyslogSuccess yes Mode&nbs........

This can break things easily in remove environments where it was normally easy to convert a normal eth0 to a bridge under br0, and that bridge would normally have the same MAC address by default, which is desirable for most situations. In Debian 11 this is different for some reason now. https://unix.stackexchange.com/questions/681013/bridge-gets-random-mac-........

Bonding is an excellent way to get both increased redundancy and throughput. It is similar to the "Network Teaming" feature in Windows. There are a few different modes but we will use mode 6, I think it's the best of both worlds, as it is not just a failover, but it provides round robin, so you will get redundancy and load balancing. So if you have a 1G single port, you will have a combined throughput of 4G at this point. Just bear in mind that the true thr........

Enable "cli" mode equivalent in JunOS cli Configure Mode configure So rather than going to the console on a Cisco switch and typing "enable" and then "conf t", the equivalent in JunOS is "cli" and "configure". How Do You Apply Changes You've Made? You can make all kinds of changes to the switch, but remember they are not........

apt install software-properties-common add-apt-repository ppa:deadsnakes/ppa apt update apt install python3-pip apt install python3.7 curl gnupg python3.7-dev git ln -s /usr/bin/python3.7 /usr/bin/python3 pip3 install numpy keras_preprocessing curl https://bazel.build/bazel-release.pub.gpg | sudo apt-key add - echo "deb [arch=amd64] http://storage.googleapis.com/bazel-apt stable jdk1.8" | sudo tee /etc/apt/sources.list.d/bazel........

If you've ever gotten errors like this the solution is simple, you need i386 enabled on your 64-bit install because wine depends on some 32-bit x86 libraries: dpkg --add-architecture i386 apt update apt install wine After that it will install just fine. apt install wine Reading package lists... Done Building dependency tree Reading state information... Done........

This is sure simple if you follow the guide but it took a lot of hacking around to make this work on Debian/Ubuntu! Now before you ask why bother running wine and python, the reason is because Python executables are NOT cross-platform. If you run pyinstaller in Linux, that binary will only run on Linux and the same if you do it in Windows. So it is preferable if you have a single environment that you can create Linux and Windows binaries from rather than running 2 separate........

This should work but the key thing is having the "-cpu host" flag. Once you add the correct -cpu host flag then it should boot just fine on KVM. qemu-system-x86_64 --enable-kvm -cpu host -smp 8 -m 8192 -drive format=raw,file=the-file.img Examples can be found here on how to boot Windows properly with KVM.........

Just edit your tftp file for xinetd like this: *Change the IPto be the IPof the interface you want to listen on. To test if your tftp is available on a certain IP range use nc -u yourip 69 to see if you can still connect (/var/log/messages or /var/log/syslog) should show the connection if it is open. Oct 13 23:20:34 01 xinetd[26631]: Started working: 1 available servic........

This is just if we have an output line. wc we know can count lines but the -w flag will count words: echo "Ihave this line here" |wc -w 5........

In Centos 7 tftpd will not work with selinux. Clients will not be able to connect and this is all you'll see in the log (then nothing more): Sep 18 14:39:15 localhost xinetd[4327]: START: tftp pid=4331 from=192.168.1.65 On the client/computer side you will see this: TFTP. PXE-M0F: Exiting Intel Boot Agent Basically the client is being instantly connected and bloc........

Having a network bridge allows you to bridge traffic under multiple devices so they can talk natively without using any special routing, iptables/firewall or other trickery. To create your bridge you need the bridge-utils package for brctl and if you want to do things like bridge VMs that run on a tap device you will need the uml-utilities which provides "tunctl". 1.) Install the utilities to make our bridge sudo apt-get i........

It is much more useful to have meaningful and detailed logging from tftp to see what is or isn't happening especially for VOIPand other embedded device appications: Edit the file: vi /etc/xinetd.d/tftp Change the server line like this: server_args = -s /var/lib/tftpboot........

Enter configuration console: enable configure terminal This is important because if your console doesn't look like below none of the commands will work! Switch(config)# Save and Apply Settings wr Show Switch Configuration: show run Show Port List/Sta........

debug1: Local connections to LOCALHOST:18006 forwarded to remote address 192.168.1.93:8006 debug1: Local forwarding listening on 127.0.0.1 port 18006. debug1: channel 0: new [port listener] debug1: Local forwarding listening on ::1 port 18006. bind: Cannot assign requested address What we are seeing is that we can't listen on an IPV6 address of ::1. We need to tell SSH to stop using IPV6 so we'll edit ssh_config to take care of this issue........

Jan 30 17:16:10 localhost sshd[25385]: error: Failed to allocate internet-domain X11 display socket. The solution for me on the server side was the following in sshd_config: AddressFamily inet *Remember to restart sshd and also reconnect from the client side. Ihad all the normal X11 settings on the server but it just stopped........

systemd is like the service manager for your Centos and other modern Linux distributions (including Debian/Mint/Ubuntu) allows you to enable services, stop them, restart them, check their status and even reboot your system. The key commands or arguments you will use with systemctl are the following: Unit Commands: list-units [PATTERN...] List loaded units &nbs........

The problem I was having is that a css template Iwas using was causing br's to have an empty line in between which is very undesirable especially when displaying code. br { display:none; margin: 0px; height: 0px; } Using CSS code like above will fix it. You technically shouldn't need the margin or height either.........

You can find many ways to specify the VLANin your network configuration but Ifind this is the simplest and quickest. In this case we are talking about a bridged adapter "vmbr0" but it works even if you just had a normal non-bridged interface. The key here is that in vmbr0 you'll notice there is no IP address. We just specify "manual". Below it is a similar stanza for "vmbr0.58" in this case 58 represents the VLAN (change........

[root@localhost:~] BootModuleConfig.sh echo host-ind nfcd........

I've read a few guides about this but they didn't work for me. sudo apt-get install bridge-utils #don't think the above is enough it won't work still even though you have by default an /etc/qemu-ifup that handles it if you have the right tools and setup sudo qemu-system-x86_64 -net tap -net nic -enable-kvm -cpu host,vmx=on ~/VirtualBox VMs/vsphere-vcenter/vsphere-vcenter.vdi W: /etc/qemu-ifup: no bridge for guest interface foun........

Sometimes if you have a very basic configuration OpenVPN on the client side for some reason sends all traffic to the OpenVPN server IP through the tun0 which is of course impossible and creates a block or routing loop. This is because you need to use your normal ISP/LANgateway to hit the OpenVPN server if it is remote/offsite as is usually the case. So if you are connected to the OpenVPN through say a tun0 device and your routing is set to connect to the OpenVPN&nbs........

Solution: Aptitude is very smart and fixed the issues it was because of nvidia cuda and opencl and nothing else suggested or hinted this using apt sudo aptitude install wine The following NEW packages will be installed: ocl-icd-libopencl1{ab} ocl-icd-libopencl1:i386{ab} wine wine1.6 wine1.6-amd64{a} wine1.6-i386:i386{a} The following packages will be REMOVED:........

To check the version of Ubuntu just use the lsb_release command as shown below and you will be able to see the exact Ubuntu version you have installed. lsb_release -a No LSB modules are available. Distributor ID: Ubuntu Description: Ubuntu 14.04 LTS Release: 14.04 Codename: trusty........

It sounds like this is corrected in later versions of the OpenVZ kernel but Iam not sure, it may also be that a much newer kernel is needed and Centos may not have a recent enough kernel. *Debain 7.0 however does work fine as a temporary fix or work around. Debian 8 OpenVZ no IP and networking not working: lo Link encap:Local Loopback  ........

#solution Edit /etc/yum.repos.d/openvz.repo For the first two entries comment out #mirrorlist and uncomment #baseurl and then it worked openvz yum problem Centos 6.5 cannot find file on mirror: yum update Loaded plugins: fastestmirror Determining fastest mirrors * openvz-kernel-rhel6: mirrors.ustc.edu.cn * openvz-utils: mirrors.ustc.edu.cn base ........

The most common solution is to use the /etc/postfix/header_checks but this is a big problem. Why is header_checks a problem? Because it does it to all mail whether incoming or outgoing and whether authenticated or not. We of course want as much header information for incoming as we can get for many reasons but many organizations want to secure and make their mail clients as secure as possible. I adapted this solution to the client's custom config, they are configur........

pxe-32 tftp open timeout The solution was to enable tftp in xinetd with "chkconfig tftp on". See the troubleshooting below: chkconfig --list NetworkManager 0:off 1:off 2:off 3:off 4:off 5:off 6:off acpid 0:off&n........

If you move your hard drive(s) around to other computers/servers, you'll find that your eth0 keeps getting higher, the first time it will become eth1 and then eth2 etc and even higher if your server has dual or quad NICs. The reason is that udevd basically assigns eth0 tot he first NIC it finds and remembers it, if it encounters a NIC with a differentMAC, it assigns it one higher (eg. eth1). See the example below, I have eth2 now so how doI fix it?........

This is something I often setup for clients because it's very helpful for people in datacenters, this allows custom OS installs on demand, you can customize it more by using kickstart etc.. but here's a base I use before customizing more: This little script below will install everything you need to get booting by PXE Linux. It also assumes you set a local IP (be sure not to overwrite your existing IP) on eth0:0 (note the :0) as 192.168.1.10 and it........

netstat is weak and can't show udp connections and most other protocols, use "ss" which is what netstat should have been: The "-u" switch stands for udp, here's a list of other options: Usage: ss [ OPTIONS ] ss [ OPTIONS ] [ FILTER ] -h, --help this message -V, --version output ver........

Centos 5 Postfix and SPAMASSASSIN Tutorial yum install spamassassin chkconfig spamassassin on vi /etc/mail/spamassassin/local.cf ############## #required_hits 5 #report_safe 0 #rewrite_header Subject [SPAM] #5 is the least restrictive (means only the most obvious SPAM is caught. 0 is obviously the most restrictive/sensitive and would have lots of false positives require........

Create Cert & Key: openssl req -new -x509 -nodes -days 1530 -out server.crt -keyout server.key mkdir /etc/mailssl chmod 700 /etc/mailssl cp server.* /etc/mailssl Postfix SSL config Edit /etc/postfix/main.cf: #SSL stuff smtpd_tls_cert_file = /etc/mailssl/server.crt smtpd_tls_key_file = /etc/mailssl/server.key To make smtps w........

Webmin Setup Centos 5: wget http://downloads.sourceforge.net/project/webadmin/webmin/1.530/webmin-1.530-1.noarch.rpm?r=http%3A%2F%2Fwww.webmin.com%2Fstandard.html&ts=1294339690&use_mirror=surfnet [1] 24229 [2] 24230 [root@host ~]# --2011-01-06 21:48:20-- http://downloads.sourceforge.net/project/webadmin/webmin/1.530/webmin-1.530-1.noarch.rpm?r=http%3A%2F%2Fwww.webmin.com%2Fstandard.html Resolving downloads.sourceforge.net... 216.34.181.........

The Xen VPSI had was not working properly and when they asked for the login information I found the support was coming directly from India: whois 122.178.148.* [Querying whois.apnic.net] [whois.apnic.net] % [whois.apnic.net node-5] % Whois data copyright terms http://www.apnic.net/db/dbcopyright.html inetnum: 122.178.128.0 - 122.178.191.255 netname:&........

After an upgrade wine wouldn't open anything, not even the pre-installed notepad. There are no wine logs and nothing is mentioned in any standard log file about why. I finally decided to run wine from the shell and see what's going on: wine client error:0: version mismatch 398/402. Your wineserver binary was not upgraded correctly, or you have an older one somewhere in your PATH. Or maybe the wrong wineserver is still running?........

Basically the two main types of distros are Debian and RHEL/Centos based. I'm just going to give a quick overview of how the configuration of IP interfaces works in Debian/Centos based distros. *Just one thing to remember, when setting IPs statically you have to manually specify a DNS server in /etc/resolv.conf (since DHCP is what normally does it automatically) Debian/Ubuntu/Kubuntu/MEPIS The IP (DHCP &........

Need identd for port 113 ? Install authdyum install authd Happy identing :)Actually it's not that simple. It installs as an "xinetd" service and is disabled and turned off by deafult. To enable it run: [code:1:8c94df8319] chkconfig --level 3 auth on service xinetd restart [/code:1:8c94df8319] This will set identd aka authd to start by default. service xinetd resta........