-?????????? ? ? ? ? ? shadow ----------. 1 root root 748 Jul 10 04:35 shadow- cat: shadow: Input/output error If you see this you are probably in big trouble, it could be a physical error or if it's a VM image that it is corrupted due to a physical error on the underlying disk/array/NAS or it could a........

I was using a small box as a router and one of the ports started going off and coming back at 100M. I truly believe it is simply that it was a case of overheating. Although CPUtemps were only about 67 degrees, the physical box itself was almost burning hot. Isolved the cooling issue and never had the issue again. Jul 28 15:09:27 swithbox kernel: e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx Jul 28 15:09:28 swithbox kernel:........

cat .htaccess RewriteEngine On RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteRule . index.php [L] I keep reading there is a "# BEGIN WordPress" and a "# END WordPress" in the wordpress htaccess above but there is clearly not. Even more strange is that my permissions are just 444 (read only). so i changed it........

If you've just installed VBox and it is not starting or working, the most common problem is usually that you don't have your kernel source installed, which means there is no kernel driver for vbox so it can't work. You may get an error that says "Kernel driver not installed" in your Virtualbox. So the first thing you should do is install your kernel source by running this: sudo apt-get install linux-headers-`uname -r`........

This works on the 2000 and 3000 series generally. *The easy way is to just hold the mode button for 10+ seconds. The full/proper way is below: 1.) Either power on the unit and hold the "mode" button or hold the "mode" button until you see the below: 00:04:08: %SYS-7-NV_BLOCK_INIT: Initalized the geometry of nvram 00:04:08: %EXPRESS_SETUP-6-CONFIG_IS_RESET: The configur........

You get errors like below and see you have all question marks for the permissions if you go to /run/user/1000/gvfs If you try to access the mounted share such as anything mounted as gvfs like an SSH share in your file manager you may get an error like this. It generally means an interruption in communication or a fault with gvfsd has caused it. Solutio........

[root@thetor2017 conf]# service httpd restart Stopping httpd: [ OK ] Starting httpd: WARNING: MaxClients of 3000 exceeds ServerLimit value of 300 servers, lowering MaxClients to 300. To increase........

This is often the result of PayPal's "item name" or another name having invalid characters or not supporting Unicode. 173.0.81.1 - - [17/Jul/2018:13:39:45 -0400] "POST //modules/gateways/callback/paypal.php HTTP/1.1" 406 - "-" "PayPal IPN ( https://www.paypal.com/ipn )" A good clue is if you check the debug output of the IPNand find a mandatory column empty. ........

Jul 3 22:12:17mailserver postfix/smtpd[6195]: fatal: no SASL authentication mechanisms Jul 3 22:12:18mailserver postfix/master[4881]: warning: process /usr/libexec/postfix/smtpd pid 6195 exit status 1 Jul 3 22:12:18mailserver postfix/master[4881]: warning: /usr/libexec/postfix/smtpd: bad command startup -- throttling This only ever happens in my experience when the authentication method is actually Dovecot. Usually the problem........

Sometimes if you have a very basic configuration OpenVPN on the client side for some reason sends all traffic to the OpenVPN server IP through the tun0 which is of course impossible and creates a block or routing loop. This is because you need to use your normal ISP/LANgateway to hit the OpenVPN server if it is remote/offsite as is usually the case. So if you are connected to the OpenVPN through say a tun0 device and your routing is set to connect to the OpenVPN&nbs........

This happens because Dovecot limits the maximum IMAPconnections per IPto just 10. This may be fine for a single client side IPbut if an entire office or multiple users are behind one IPor a single heavy user is active then you will get bizarre errors in your e-mail clients such as "Password Incorrect" or similar in Thunderbird. It won't be obvious on the client side as to what the problem is and they will probably just think the server is misconfi........

vzkernel-2.6.32-042stab116.2.x86_64.rpm&n........

I wanted to use Astrachat because it seems to be the only app that has video, pic and file sharing for Jabber butI cannot even connect despite any other client working fine including Xabber and others. astrachat "Oops.. We can't connect to the account that you provide above. Please recheck your account detail". Unfortunately to make it worse there doesn't seem to be any error log or more details about the issue. The jab........

I flashed an LSI Logic firmware to it and it broke the BIOS (cannot do Ctrl+R) for booting purposes but allows other functionality to work normally. I tried downgrading to a Dell firmware for Perc 6i but it won't work, not even with MegaCli wget http://downloads.dell.com/FOLDER00416606M/1/SAS-RAID_Firmware_W83M2_LN32_6.3.1-0003_A14.BIN --2013-08-26 12:53:39-- http://downloads.dell.com/FOLDER00416606M/1/SAS-RAID_Firmware_W83M2_LN32_6.3.1-0003_A14.BIN Resolvi........

Jul 11 15:20:58 tor sendmail[9617]: r6AKjOD07: to= mailserver.com was the hostname of the server, sendmail sends this by default and many mailservers will reject mail to a hostname that does not resolve or exist. The easiest way is just to change the hostname and make sure it does resolve to something. I read there is a way in sendmail.mc to manually set a hostname but I never got it working: vi /etc/mail/sendmail.mc define(`confDOMAIN........

Client Log OpenSSH_4.3p2, OpenSSL 0.9.8e-fips-rhel5 01 Jul 2008 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug1: Connecting to 192.168.1.253 [192.168.1.253] port 22. debug1: Connection established. debug1: permanently_set_uid: 0/0 debug1: identity file /root/.ssh/identity type -1 debug1: identity file /root/.ssh/id_rsa type 1 debug1: identity file /root/.ssh/id_d........

I found this technique listed in many places which shows you how to use a common Linux tool "dd" to dump the raw partition of your iPhone. I give credit to this site for showing me the correct way to dd from the iPhone, I never thought to try it in the other direction:http://log.ijulien.com/post/182804914/iphone-3gs-data-recovery Requirements 1.) Jailbreak your........

This error is annoying, in a Virtuozzo KB entry about this ip tables nat problem they say the kernel needs to be ugpraded: Symptoms The node runs 2.6.18-x kernel older than 2.6.18-028stab053.10. NAT module does not work in container, you get "can't initialize iptables table 'nat'" error: # iptables -t nat........