Using Cisco CME Router with Asterisk as a dial-peer

#Remember that you need a valid gateway IPunless the Asterisk server is on the same subnet and LAN Set Valid Gateway IP (if you don't have one already) ip route 0.0.0.0 0.0.0.0 GATEWAYIP Enable VOIPTrust voice service voip ip address trusted list ipv4 0.0.0.0 0.0.0.0 sip Set Credentials For Asterisk and Register To Asterisk sip-ua........

CentOS 7 fix Could not retrieve mirrorlist http://mirrorlist.centos.org/?release=7&arch=x86_64&repo=os&infra=container error was 14: curl#6 -

yum update Loaded plugins: fastestmirror, ovl Determining fastest mirrors Could not retrieve mirrorlist http://mirrorlist.centos.org/?release=7&arch=x86_64&repo=os&infra=container error was 14: curl#6 - "Could not resolve host: mirrorlist.centos.org; Unknown error" One of the configured repositories failed (Unknown), and yum doesn't have enough cached data to continue. At this point the onl........

REFUSED unexpected RCODE resolving bind/named error

Are you getting this error when trying to connect to a site/domain/service and then you checked your router/nameserver's logs to see what's wrong? You may see something like this: named[3025898]: REFUSED unexpected RCODE resolving This is not usually an error with named or bind, at least not on your end but NORMALLY this is an issue with the remote nameserver. A lot of times this is a misconfigured remote nameserver. A classi........

apache2 httpd apache server will not start [pid 22449:tid 139972160445760] AH00052: child pid 23248 exit signal Aborted (6) solution Mint Debian Ubuntu Redhat

If you get this error, it is often because you have configured Apache with modules that weren't actually installed. Eg. you try to load the PHPmodule but didn't actually install the apache2 php module, so the server can't start. In general, this error can often be caused by issues with problematic modules and/or Apache being configured for modules that have not actually be installed (eg. libapache2-mod-php) is missing. The above results in this less than obv........

Linux Ubuntu Mint how to check nameservers when /etc/resolv.conf disabled solution

You'll notice that /etc/resolv.conf contains dire warners on most Linux Desktops. # This file is managed by man:systemd-resolved(8). Do not edit. # # This is a dynamic resolv.conf file for connecting local clients to the # internal DNS stub resolver of systemd-resolved. This file lists all # configured search domains. # # Run "resolvectl status" to see details about the uplink DNS servers # currently in use........

How to install and configure haproxy on Linux Ubuntu Debian

haproxy is one of the best known and widely used Open Source load balancers out there and a strong competitor to nginx. haproxy is used by many large sites per Wikipedia: HAProxy is used by a number of high-profile websites including GoDaddy, GitHub,........

VboxManage VirtualBox NAT Network Issues Managment Troubleshooting

If you find your NAT Network is not working properly, the first thing you may want to do is list the networks, check their status and make sure the Network is actually started and configured as you expect (eg. is DHCP on and enabled?). This is a long known, unresolved bug that seems to affect Version 6 randomly and disportionately on especially Mint 20/Ubuntu 18. https://www.virtualbox.org/ticket/1474........

Cisco Switch / Router How To Restore Factory Default Settings

1.) Make sure your conf register is 0x2102 Do show version and at the very end of the output you will see the Configuration register. show version Configuration register is 0x2102 If the config register is not 0x2102 then enter this command: r1#configure terminal r1(config)#config-register 0x2102 r1(config)#end 2.) Let's Erase the NVRAM/flash........

Cisco 2900 3900 Router Password Reset How To Reset Enable Password

It is a bit different and annoying here for these types of routers/models as you need to physically remove the CF (Compact Flash) and only then, will it enter ROMMON mode (Ctrl + Pause remotely over the console will not do it for us). This means you cannot do this remotely, or at least not without the help of a remote/physical helper. Step 1.) Power off, router and remove CF Disk Slot#2 Go to the router and remove the slot#2 cover uses your hand or it may help to use a........

ssh Too many authentication failures not prompting for password

If you get this error when trying to SSHto a device or machine and you never even got a password prompt: Too many authentication failures This means that either the remote side is configured for key auth only, OR your client side may be attempting to auth using mulitple keys, and that exceeds the amount of attempted authorizations on the remote ssh server. If the issue is trying to auth too many times which ssh defaults to sending the keys to, you ca........

How To Do Linux Network Bonding Teaming in Mint Debian Ubuntu

Bonding is an excellent way to get both increased redundancy and throughput. It is similar to the "Network Teaming" feature in Windows. There are a few different modes but we will use mode 6, I think it's the best of both worlds, as it is not just a failover, but it provides round robin, so you will get redundancy and load balancing. So if you have a 1G single port, you will have a combined throughput of 4G at this point. Just bear in mind that the true thr........

Docker Tutorial HowTo Install Docker, Use and Create Docker Container Images Clustering Swarm Mode Monitoring Service Hosting Provider

The Best Docker Tutorial for Beginners We quickly explain the basic Docker concepts and show you how to do the most common tasks from starting your first container, to making custom images, a Docker Swarm Cluster Tutorial, docker compose and Docker buildfiles.........

tag#4 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE tag#4 Sense Key : Illegal Request [current] res 40/00:b4:98:02:00/00:00:00:00:00/40 Emask 0x10 (ATA bus error) solution

You might assume you have a bad drive or the SATA interface/cable is bad, or the power supply is bad/weak to the drive. These are all possible issues, but definitely check your SATA cable for "twisting". It is a big issue because until the error stops or times out, your system will not boot (in my case this was the case even though the drive with the issue was not part of the OS or booting process at all). If you run an open rig that you move around often that ha........

Unable to mount location Failed to retrieve share list from server: Connection timed out - Samba/Linux Filesharing Not working Ubuntu Mint Linux Solution

So you're trying to browse to a properly configured Samba share but you get this error: Unable to mount location Failed to retrieve share list from server: Connection timed out If your config is right, it can be due to a protocol miss-match where your client has not enabled SMB3 but by default the other side (server) has enabled it. You can test this out to see with the smbclient tool........

EFI PXE grub2 Howto guide for Linux EFI PXE Booting on Debian, Mint, Ubuntu, RHEL

Just a quick note and warning is that if you are testing to see if EFIPXE booting works on a VM, MAKE SURE it actually works. For example Iinitially tested using my Distro's QEMU 2.5+dfsg-5ubuntu10.46 and ovmf BIOS firmware (OVMF supports EFI). However, I found on old versions of QEMU (like 2.5), EFIbooting with GRUB NEVER works so it may appear that you have made a mistake when everything is fine when you boot a physi........

Juniper JunOS Command Overview and Howtos Switch, Router, Firewall Tutorial Guide

Enable "cli" mode equivalent in JunOS cli Configure Mode configure So rather than going to the console on a Cisco switch and typing "enable" and then "conf t", the equivalent in JunOS is "cli" and "configure". How Do You Apply Changes You've Made? You can make all kinds of changes to the switch, but remember they are not........

How To Get Started on Ubuntu with gpt-2 OpenAI Text Prediction

apt install software-properties-common add-apt-repository ppa:deadsnakes/ppa apt update apt install python3-pip apt install python3.7 curl gnupg python3.7-dev git ln -s /usr/bin/python3.7 /usr/bin/python3 pip3 install numpy keras_preprocessing curl https://bazel.build/bazel-release.pub.gpg | sudo apt-key add - echo "deb [arch=amd64] http://storage.googleapis.com/bazel-apt stable jdk1.8" | sudo tee /etc/apt/sources.list.d/bazel........

Linux How To Change NIC Name to eth0 instead of enps33 or enp0s25

Most newer distros inexplicably cause your NIC to have what Icall "random" non-standard name conventions because of systemd. This is a big problem for many people and especially those running servers. Imagine that you have a static IPconfigured for ens33 but then the hard disk is moved to a newer system, the NIC could be anything from ens33 to enp0s1, meaning that manual intervention is required to go and update the NIC config file (eg. /etc/network/interfa........

MySQL 5.7 on Debian and Ubuntu - How To Reset Root Password

MySQL on Debian versions is configured differently than the native local MySQL plugin so you will be disappointed when your password on the mysql client fails by default. Here is how you reset the MySQL root password the proper and "working way" #first we gracefully stop mysql sudo systemctl stop mysql; #then we forcefully kill any mysqld process just in case sudo killall -9 mysqld mysqld_safe;........

how to use ifplugd in Linux to execute a command or script when a NIC cable is unplugged or plugged in

It is fairly simple to use once you know how to use it. However, the tricky thing is that by default it doesn't seem to be active or listen on any interface on manually specified. How To Install ifplugd First we install ifplugd sudo apt install ifplugd Let's enable it on our desired device(s) vi /etc/default/ifplugd set this line as so:........

How To Install Asterisk 16 17 on Debian Ubuntu Linux

Downloading and compiling from source to get the latest version of Asterisk is really simple with this guide. apt install gcc make g++ libedit-dev uuid-dev libjansson-dev apt install libxml2-dev sqlite3 libsqlite3-dev wget http://downloads.asterisk.org/pub/telephony/asterisk/asterisk-16-current.tar.gz tar -zxvf asterisk-16-current.tar.gz cd asterisk-16.6.2/ ./configure If you get this error change y........

Cisco DHCP Snooping Relay Setup Information

Switch#show ip dhcp snooping Switch DHCP snooping is disabled DHCP snooping is configured on following VLANs: 1 Insertion of option 82 is enabled circuit-id format: vlan-mod-port remote-id format: MAC Option 82 on untrusted port is not allowed Verification of hwaddr field is enabled Interface&nb........

How Does Cisco CUCM (Cisco Unified Communication Manager) Work?

Cisco's CUCM (Cisco Unified Communication Manager) is a system that combines voice, video, data and mobile products into a single unified management suite. At its core, the CUCMis like a "Super PBX" that controls the flow of all communications through an organization even single or multiple site deployments. Cisco's CUCMmakes communication more effective and simple through centralized management and unification of communications resources.........

PHP Displaying Blank Page on Apache

Almost always the reason will be that the php.so file is missing but also that php.conf is misconfigured. In the problem machine it is actually PHP7 installed so if you reference PHP5 of course things wil be broken! Take for example here: cat /etc/httpd/conf.d/php.conf # # PHP is an HTML-embedded scripting language which attempts to make it # easy for developers to write dynamica........

VMWare Hardware virtualization is selected and cannot be deselected due to selection of VBS Insufficient resources to satisfy configured failover level for vSphere HA.

There is no such option as "VBS" that Ican see in vSphere 6.7 Ibelieve this is actually an issue because of using old hardware in this case L5420 doesn't support Nested Virtualization I believe. Hardware virtualization is selected and cannot be deselected due to selection of VBS Insufficient resources to satisfy configured failover level for vSphere HA.........

VMWare 6.7 VCSA VSphere ESXi Management SSO Install Guide on Linux using the CLI

#mount the VCSA DVD mount /dev/sr0 /mnt/cd #alternatively you could mount the iso directly mount -o loop vcsa.iso /your/mount/path #for this purpose we are using the CLI installer on Linux cd /mnt/cd/vcsa-cli-installer/lin64 #no it's not going to be that easy you can't just run vcsa-deploy like that you need to use a template or configured .json file ./vcsa-deploy Usage: vcsa-deploy [-h] [--version] [--supported-deploymen........

Cannot create gradle for conversations

The main issue is it looks like Java is not configured to accept the invalid ssl cert that is coming from the download location. Exception in thread "main" java.lang.RuntimeException: javax.net.ssl.SSLException: java.security.ProviderException: java.security.InvalidKeyException: EC parameters error export ANDROID_HOME=/home/user/Downloads/tools/ Conversations-master$ ./gradlew Downloading https://services.gradle.org/distributions/grad........

Maximum number of connections from user+IP exceeded (mail_max_userip_connections=10) Dovecot Solution

This happens because Dovecot limits the maximum IMAPconnections per IPto just 10. This may be fine for a single client side IPbut if an entire office or multiple users are behind one IPor a single heavy user is active then you will get bizarre errors in your e-mail clients such as "Password Incorrect" or similar in Thunderbird. It won't be obvious on the client side as to what the problem is and they will probably just think the server is misconfi........

Centos 7 Cudaminer Nvidia setup guide

I am using a GTX 1060 but replace the download for the driver with the correct/current version for your particular card by visiting: http://www.nvidia.com/Download/index.aspx?lang=en-us yum install automake curl openssl-devel libcurl-devel gcc gcc-c++ yum -y install kernel-devel-`uname -r` yum -y install unzip #the........

Linux Mint Install Netboot PXE Guide Howto

*Update so this doesn't work it must be something to do with the path of nfs or something else but the installer fails with "Installer crashed" at the end whereas with the CD/USB it works. This assumes you've already installed and configured a separate PXE/DHCP server somewhere else and your /tftpboot directory is setup. This is for Linux Mint 18.1 but generally applies to most versions although you may have tro change things like "casper"........

ERROR 2013 (HY000): Lost connection to MySQL server during query

The solution is simple but strange, if you copy your /var/lib/mysql directory to another server and think it will work, be sure to check if you have /var/log/mysql and binary log files. If you do, the server will not work and will give you errors like below and crash without the proper log files. UPDATE user SET password=password("newpass") WHERE user='root'; flush privileges; ERROR 2013 (HY000): Lost connection to MySQL server durin........

/dev/drbd0: State change failed: (-2) Need access to UpToDate data solution

Everytime I've seen this error "/dev/drbd0: State change failed: (-2) Need access to UpToDate data" it is because DRBD has no disk: cat /proc/drbd version: 8.3.13 (api:88/proto:86-96) GIT-hash: 83ca112086600faacab2f157bc5a9324f7bd7f77 build by root@sighted, 2012-10-09 12:47:51 0: cs:Connected ro:Secondary/Secondary ds:Diskless/Inconsistent A r----- ns:0 nr:0 dw:0 dr:0 al........

Nvidia Linux Card not working due to LSI 9200/SAS2008 IRQ conflict

At first my BIOS said the card may not work right because there is no more option ROM space. I disabled the Option ROM for both LSI 1068 and 2008 chipsets, Network Boot ROM and most other PCI slots, Serial Port, etc... and the message went away but the card still does not work properly. But it still cannot initialize the card properly(does not work): [ 33.943272] NVRM: This PCI I/O region assigned to your NVIDIA device is invalid:........

status: { DRDY ERR } error: { ICRC ABRT } failed command: WRITE FPDMA QUEUED MCP55 Linux Errors

[ 2868.041375] ata1: EH in SWNCQ mode,QC:qc_active 0x40 sactive 0x40 [ 2868.041554] ata1: SWNCQ:qc_active 0x40 defer_bits 0x0 last_issue_tag 0x6 [ 2868.041556] dhfis 0x40 dmafis 0x40 sdbfis 0x20 [ 2868.041874] ata1: ATA_REG 0x41 ERR_REG 0x84 [ 2868.042013] ata1: tag : dhfis dmafis sdbfis sactive [ 2868.042163] ata1: tag 0x6: 1 1 0 1 [ 2868.042301] ata1.00: exception Emask 0x1 SAct 0x40 SErr 0x400000 action 0x6 frozen [........

Postfix how to secure outgoing authenticated e-mails for privacy and hide the IP address, mailer and other things

The most common solution is to use the /etc/postfix/header_checks but this is a big problem. Why is header_checks a problem? Because it does it to all mail whether incoming or outgoing and whether authenticated or not. We of course want as much header information for incoming as we can get for many reasons but many organizations want to secure and make their mail clients as secure as possible. I adapted this solution to the client's custom config, they are configur........

OpenVZ mismatched kernel and dev when compiling.

./configure ./configure: line 91: cd: /lib/modules/2.6.32-042stab084.25/build: No such file or directory Error: kernel version not found. Please make sure your kernel is configured. dr-xr-xr-x. 4 root root 4096 Feb 21 06:13 .. lrwxrwxrwx 1 root root 45 Feb 21 06:13 build -> ../../../usr/src/kernels/2.6.32-042stab084.25 drwxr-xr-x 2 root root 4096 Feb 12 20........

What a hdd hard drive and mdadm RAID array failure looks like in Linux

[3805108.257042] sd 0:0:0:0: [sda] 1953525168 512-byte hardware sectors: (1.00 TB/931 GiB) [3805108.257052] sd 0:0:0:0: [sda] Write Protect is off [3805108.257054] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [3805108.257066] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [3805108.257083] sd 0:0:0:0: [sda] 1953525168 512-byte hardware sectors: (1.00 TB/931 GiB) [3805108.257090] sd 0:0:0:0: [sda] Write Protect is off........

Dell Perc 6/i SATA benchmarks without battery

The results are not bad, the Hitachi performs the same as it does in a SATA2 motherboard. However, the 2TB is much different, on a similar 2TB Toshiba I get about 198MB/s on a different motherboard vs the 2TB Hitachi which should produce similar results. This Dell Perc 6/i is on a PCI x8 riser card and is connected to a 12-port backplane. Adapter #0 Enclosure Device ID: 32 Slot Number: 0 Enclosure position: N/A De........

LSI MegaRAID Adventures, Guide and HowTo

LSi Megaraid At first it was configured as a RAID 0, then I deleted the Virtual Disk Group. I thought both drives would be shown and detected in Linux as sda and sdb but it actually shows nothing. To make them work you have to hit Ctrl+R before the system boots (when prompted) and create a Virtual Disk Group. In my case I created each one as RAID 0 (with a single drive only) as I just wanted JBOD but there is no such option or default in these Dell Pe........

WD 20EARX Dead Again

Another new drive bad from the start: Jun 2 15:14:18 one-desktop kernel: [15895.386779] ata2.00: exception Emask 0x50 SAct 0x1 SErr 0x280900 action 0x6 frozen Jun 2 15:14:18 one-desktop kernel: [15895.386782] ata2.00: irq_stat 0x08000000, interface fatal error Jun 2 15:14:18 one-desktop kernel: [15895.386784] ata2: SError: { UnrecovData HostInt 10B8B BadCRC } Jun 2 15:14:18 one-desktop kernel: [15895.386788] ata2.00: cmd 60/0........

Asterisk DOS attack - failed for '173.242.117.192' - Peer is not supposed to register [May 23 15:46:07] ERROR[32748]: chan_sip.c:13158 register_verify: Peer '153' is trying to register, but not configured as host=dynamic

This happened to a customer Asterisk server and it somehow found the ID of the registration account to the upstream SIP server and was railing connection attempts (it filled up the console and there were literally thousands per second). Basically this caused all incoming and outgoing calls to fail. It was a temporary fix but the solution was to block that specific IP, it's hard to stop it 100% because the customer needs the default SIP port.........

WD 20EARX 2TB Bad within days

This is just trying to read 5GB off the drive with dd and the drive initially tested ok but shortly after I wondered why I was seeing 2MB/s read speeds. Notice the "current_pending_sector", anytime I've seen it at anything above 0 even with no other bad fields/attributes, it means the drive is bad. ata1.00: exception Emask 0x0 SAct 0x3 SErr 0x0 action 0x0 ata1.00: irq_stat 0x40000008 ata1.00: failed command: READ FPDMA QUEUED ata1.00: cmd 60/00:00:........

Powersupply Issue, Motherboard AHCI issue?

This is the most I can get when plugging in a hard drive hot and only on some power connectors. [71656.314271] ata5: exception Emask 0x50 SAct 0x0 SErr 0x90a02 action 0xe frozen [71656.314277] ata5: irq_stat 0x00400000, PHY RDY changed [71656.314285] ata5: SError: { RecovComm Persist HostInt PHYRdyChg 10B8B } [71656.314294] ata5: hard resetting link [71660.360686] ata5: softreset failed (device not ready) [71660.360694] ata5: applying........

Setup PXE Boot using Centos and dhcpd, tftp and syslinux

This is something I often setup for clients because it's very helpful for people in datacenters, this allows custom OS installs on demand, you can customize it more by using kickstart etc.. but here's a base I use before customizing more: This little script below will install everything you need to get booting by PXE Linux. It also assumes you set a local IP (be sure not to overwrite your existing IP) on eth0:0 (note the :0) as 192.168.1.10 and it........

failed to IDENTIFY (INIT_DEV_PARAMS failed, err_mask=0x80)

[ 12.460014] ata1: SRST failed (errno=-16) [ 17.626677] ata1: link is slow to respond, please be patient (ready=0) [ 22.480011] ata1: SRST failed (errno=-16) [ 27.646681] ata1: link is slow to respond, please be patient (ready=0) [ 38.106817] ata1.01: failed to IDENTIFY (INIT_DEV_PARAMS failed, err_mask=0x80) [ 48.266676] ata1: link is slow to respond, please be patient (ready=0)........

How To Test If Your Hard Drive Is Good/Signs of dying hard drive

I like dd, although it only reads it, usually a read test of the entire disk will uncover if your hard drive is bad in some parts. This is a good thing to do at least once a month, a lot of times bizarre program behavior, laginess and crashing/unnmounting problems etc.. are due to a failing disc and SMART won't know it or indicate a problem: We must also remember there's never a guarantee, I've found that ever since we moved to larger and more platters per drive with 1TB drives........

Are my WDEARS20 Drives dying already?

This happened during a RAID array check: SMART says both drives pass the test, but I'm doing a long test on them and hopefully this is not a hardware error. Apr 3 04:22:01 remote kernel: md: syncing RAID array md2 Apr 3 04:22:01 remote kernel: md: minimum _guaranteed_ reconstruction speed: 1000 KB/sec/disc. Apr 3 04:22:01 remote kernel: md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for reconstruction. Apr........

Postfix/Any Email Server check for Open Relay

The first thing you need to remember is not to check from the same host/server itself. This is a silly mistake I made, the reason is that many mailservers and especially postfix are configured to allow relaying from the localhost/same host. If you do that you'll get a false positive. *Make sure you test from another host/system than the mail server itself! telnet yourmailserverhost.com 25 220 Courier (FreeBS........

Failed to save enabled features : The Suexec command on your system is configured to only run scripts under /var/www, but the Virtualmin base directory is /home. CGI and PHP scripts run as domain owners will not be executed.

Apache/httpd Failed to save enabled features : The Suexec command on your system is configured to only run scripts under /var/www, but the Virtualmin base directory is /home. CGI and PHP scripts run as domain owners will not be executed. This is because I never edited the Apache Config and Virtualmin config to reflect my new/current updated structure.........

Webmin/Virtualmin when enabling bind: Failed to save enabled features : Virtualmin is configured to setup DNS zones, but this system is not setup to use itself as a DNS server. Either add 127.0.0.1 to the list of DNS servers, or turn off the BIND fe

Webmin/Virtualmin when enabling bind: Failed to save enabled features : Virtualmin is configured to setup DNS zones, but this system is not setup to use itself as a DNS server. Either add 127.0.0.1 to the list of DNS servers, or turn off the BIND feature on the module config page. It means what it says, add "127.0.0.1" to /etc/resolv.conf........

Installing Webmin & Enabling SSL

Webmin Setup Centos 5: wget http://downloads.sourceforge.net/project/webadmin/webmin/1.530/webmin-1.530-1.noarch.rpm?r=http%3A%2F%2Fwww.webmin.com%2Fstandard.html&ts=1294339690&use_mirror=surfnet [1] 24229 [2] 24230 [root@host ~]# --2011-01-06 21:48:20-- http://downloads.sourceforge.net/project/webadmin/webmin/1.530/webmin-1.530-1.noarch.rpm?r=http%3A%2F%2Fwww.webmin.com%2Fstandard.html Resolving downloads.sourceforge.net... 216.34.181.........

Virtualmin/Webmin Postfix Error: The status of your system is being checked to ensure that all enabled features are available, that the mail server is properly configured, and that quotas are active ..

Virtualmin Postfix Error: The status of your system is being checked to ensure that all enabled features are available, that the mail server is properly configured, and that quotas are active .. A problem was found with your Postfix virtual maps : No map sources were found in the Postfix configuration .. your system is not ready for use by Virtualmin. ........

Dying Seagate 7200.11 SD15

[137392.910057] ata4.00: exception Emask 0x0 SAct 0x1 SErr 0x80000 action 0x6 frozen [137392.910077] ata4: SError: { 10B8B } [137392.910095] ata4.00: cmd 60/20:00:00:00:00/00:00:00:00:00/40 tag 0 ncq 16384 in [137392.910099] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [137392.910122] ata4.00: status: { DRDY } [137392.910135] ata4: hard resetting link [137393.440060] ata4: SATA link........

Ubuntu/Debian DRBD 8.0 Setup Guide

I've only used it on Centos, soI thought I'd make a quick Debian guide: Install the DRBD Package apt-get install drbd8-utils Reading package lists... Done Building dependency tree Reading state information... Done The following packages were automatically installed and are no longer required: libswfdec-0.8-0 Use 'apt-get autoremove' to remove them. The following........

mdadm RAID 1 adventures

I separated the 2 drives in the RAID 1 array. 1 is the old one /dev/sda and is out of date, while the separated other one /dev/sdc was in another drive and mounted and used with more data (updated). I wonder how mdadm will handle this: usb-storage: device scan complete md: md127 stopped. md: bind md: md127: raid array is not clean -- starting background reconstruction raid1: raid set md127 active with 1 out of 2 m........

mdadm when a RAID 1 member dies

[27969.398749] sd 5:0:0:0: [sdb] 3907029168 512-byte hardware sectors (2000399 MB) [27969.398749] sd 5:0:0:0: [sdb] Write Protect is off [27969.398749] sd 5:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [27969.398749] sd 5:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [27972.117543] ata6.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x0 [27972.117543] ata6.00: irq_stat 0x48000000 [27972.117543] ata6.00: cmd 60/08:00:ff:7........

Fix Slow 2D Graphics Xorg.conf Ubuntu/Debian/Mandriva Linux

I'm using Ubuntu 8.04 but anyone using older kernels will find this may apply to them. My Intel graphics are very slow with the default Xorg settings but by using "EXA" acceleration, scrolling down windows of text becomes pretty snappy. Just edit /etc/X11/xorg.conf Section "Device" Identifier "Configured Video Device" &nb........

Seagate Drive 500GB Drive Dying

This drive is clearly on the way out, the Kernel knows it but I'm surprised that SMART is not concerned. I didn't blame Seagate for their past issues until now. This hard drive has hardly been used and has not even been powered on for a year according to SMART. Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.11 Device........

Linux AHCI Hotswap Tips - Remember To Reread The Partition Table WITHOUT rebooting

From the package "parted" you can use the command "partprobe" to re-read the partition table. I really hate rebooting, and that's what Iloved to hear about AHCI motherboards, that they allow hotswap so you don't have to reboot. But that's only as good as the OS, if the OS does not reload the partition table you won't be able to do anything with that new drive you attached without rebooting. Yes, even without re-reading the partiton table Linux will........

Need identd for port 113 ? Install authd

Need identd for port 113 ? Install authdyum install authd Happy identing :)Actually it's not that simple. It installs as an "xinetd" service and is disabled and turned off by deafult. To enable it run: [code:1:8c94df8319] chkconfig --level 3 auth on service xinetd restart [/code:1:8c94df8319] This will set identd aka authd to start by default. service xinetd resta........