Virtualbox is a very powerful tool, but for some use cases it is less than optimal. Say you are in a work, lab or other environment where you are not alone on the physical network and there could be overlap of IPs, but you need all of your VMs to be contactable from your host, VMs need to communicate with each other, and VMs need internet. NAT Network will give you VM to VM communication and internet, however, it is buggy and unstable. It also doesn't allow host to VM co........

Bonding is an excellent way to get both increased redundancy and throughput. It is similar to the "Network Teaming" feature in Windows. There are a few different modes but we will use mode 6, I think it's the best of both worlds, as it is not just a failover, but it provides round robin, so you will get redundancy and load balancing. So if you have a 1G single port, you will have a combined throughput of 4G at this point. Just bear in mind that the true thr........

There is a random bug that sometimes occurs with Vbox NAT mode DNS, although it has never happened in the past and Vbox was working fine until recently. The symptom is that you can see it does get an IP+ DNS from the Vbox NAT DHCP. Below we use resolvectl dns and verify the DNS server is set to 10.0.2.3 which is the DNS from Vbox NAT. We can ping it but it does not respond to any DNS requests when we use dig @10.0.2.3 realtechtalk.com........

NAT Network, the VMs can communicate but your host cannot access them by default. NAT VMs have internet but cannot communicate with each other. Bridged is simple and allows full LAN access as if you had a physical machine plugged in but is often bad for testing, work or corporate environments and is not very portable when it comes to moving your VMs to other locations and networks. Here is how you can use NAT Ne........

Having a network bridge allows you to bridge traffic under multiple devices so they can talk natively without using any special routing, iptables/firewall or other trickery. To create your bridge you need the bridge-utils package for brctl and if you want to do things like bridge VMs that run on a tap device you will need the uml-utilities which provides "tunctl". 1.) Install the utilities to make our bridge sudo apt-get i........

You can find many ways to specify the VLANin your network configuration but Ifind this is the simplest and quickest. In this case we are talking about a bridged adapter "vmbr0" but it works even if you just had a normal non-bridged interface. The key here is that in vmbr0 you'll notice there is no IP address. We just specify "manual". Below it is a similar stanza for "vmbr0.58" in this case 58 represents the VLAN (change........

I've read a few guides about this but they didn't work for me. sudo apt-get install bridge-utils #don't think the above is enough it won't work still even though you have by default an /etc/qemu-ifup that handles it if you have the right tools and setup sudo qemu-system-x86_64 -net tap -net nic -enable-kvm -cpu host,vmx=on ~/VirtualBox VMs/vsphere-vcenter/vsphere-vcenter.vdi W: /etc/qemu-ifup: no bridge for guest interface foun........

VMWare bridged adapter not working: Message from system: The network bridge on device vmnet0 is not running. The virtual machine will not be able to communicate with the host or with other machines on your network. Failed to connect virtual device Ethernet1. I'm not sure how to fix this but one of the issues is that my eth0 became eth1 after moving my hard drives to a new motherboard. I have run the vmware-config.pl but this did not resolve the issue.........

The New Chips on the BlockThe New Chips on the Block By Bruce Gain Story location: http://www.wired.com/news/infostructure/0,1377,67795,00.html 02:00 AM Jun. 13, 2005 PT We have embarked upon a new era in x86 PC computing -- so say chip giants AMD and Intel following their launches of dual-core PC processors. So how will dual-core processing change your PC computing experience? Our FAQ should help you decide whether or when you sho........