The easiest way to know if your videos are playing with GPU acceleration are to watch the process of xplayer, mpv or whatever you are playing. The CPU usage should be no more than 10% for that process/program if it is using acceleration.
Let's manually play with vdpau to make sure it works before we make it permanent:
First make sure you have libvdpau installed:
sudo apt install vdpau-driver-all
If yo........
The strange thing is that usually the first install or two will work on any new machine but then it suddenly won't. I had this experience on QEMU 2.13 on a different machine. There is something finicky or buggy about the CUCM installer even when choosing the same virtual hardware specs.
qemu-kvm command:
/usr/libexec/qemu-kvm -version
QEMU PC emulator version 0.12.1 (qemu-kvm-0.12.1.2-2.506.el6_10.1), Copyright (c) 2003-2008 Fabrice Bellard
........
In most of the Cisco router IOS I find the ports like ge0/0 ge0/1 and ge0/2 or whatever your ports are down. They will not even give you a link light. So one of the first tasks should be getting the port you are working with up.
In my case the first goal is often connectivity with the LAN and WAN.
LAN = your local area network (eg. in the office/home )
WAN= your ISP/public internet (eg. fiber/cable/dsl/ethernet).
In these examples I as........
Switch#show ip dhcp snooping
Switch DHCP snooping is disabled
DHCP snooping is configured on following VLANs:
1
Insertion of option 82 is enabled
circuit-id format: vlan-mod-port
remote-id format: MAC
Option 82 on untrusted port is not allowed
Verification of hwaddr field is enabled
Interface&nb........
Enter configuration console:
enable
configure terminal
This is important because if your console doesn't look like below none of the commands will work!
Switch(config)#
Save and Apply Settings
wr
Show Switch Configuration:
show run
Show Port List/Sta........
This works on the 2000 and 3000 series generally.
*The easy way is to just hold the mode button for 10+ seconds.
The full/proper way is below:
1.) Either power on the unit and hold the "mode" button or hold the "mode" button until you see the below:
00:04:08: %SYS-7-NV_BLOCK_INIT: Initalized the geometry of nvram
00:04:08: %EXPRESS_SETUP-6-CONFIG_IS_RESET: The configur........
You can find many ways to specify the VLANin your network configuration but Ifind this is the simplest and quickest.
In this case we are talking about a bridged adapter "vmbr0" but it works even if you just had a normal non-bridged interface.
The key here is that in vmbr0 you'll notice there is no IP address. We just specify "manual".
Below it is a similar stanza for "vmbr0.58" in this case 58 represents the VLAN (change........
[root@localhost:~]
BootModuleConfig.sh echo host-ind nfcd........
Centos when copying old files and restarting it seems load everything fine and then says [FAILED] with no log or other message.
service restart named
named [FAILED]
Check more thoroughly you may have missed the error if you have lots of zones!
service named restart|grep error
zone 1.168.192.in-addr.arpa/IN: not loaded due to errors.
zone 2.168.192.in-addr.arpa/IN: no........
This is a VIA made VL805 USB 3.0 Chipset with 4-ports and MOLEX powered. First of all this unit was cheap at about only 9 USD with fast shipping. My biggest concern was if this was a quality unit and would it really give you full USB 3.0 speeds (some people reported with similar cards that for some weird r........
If you have this problem: http://realtechtalk.com/mencoder_bmovl_error_vf_bmovl_Unknown_command_Ignoring_-1860-articles
Then ffmpeg is for you. Go here if you are using Linux Mint and cannot find or install it to use an external PPA........
Based on this tutorial: http://www.linuxjournal.com/content/overlay-images-video-using-mplayer-and-mencoder
mencoder -oac pcm -ovc raw -vf bmovl=0:0:tfifo -o $output $file
vf_bmovl: Unknown command: ''. Ignoring. ........
forcedeth 0000:00:08.0: irq 25 for MSI/MSI-X
forcedeth 0000:00:08.0: eth0: MSI enabled
forcedeth 0000:00:08.0: eth0: no link during initialization
ADDRCONF(NETDEV_UP): eth0: link is not ready
forcedeth 0000:00:08.0: eth0: link up
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Dec 1 18:21:32 box15 kernel: forcedeth: Reverse Engineered nForce ethernet driver. Version 0.64.
Dec 1 18:21:32 box15 kernel........
First of all this seems to apply to many ONVIF devices
Hard coded IP: 192.168.1.10 (yes not kidding no DHCP!)
00:12:12:9C:C2:00
To view RTSP stream use VLC, or openRTSP or other RTSP capable software:
rtsp://192.168.1.10/user=admin_password=tlJwpbo6_channel=1_stream=0.sdp
user: admin
password: blank
http://ip/Login.htm
Uses Quicktime and is a poor quality picture and slow
Cannot change pass........
If the below is happening on KVM (a very weird and scary looking error) it's probably because of Windows. This has happened countless times to me where the bootsector on Windows 7/2008 becomes corrupted easily (even by a crash or shutdown).
KVM: unknown exit, hardware reason 0x80000021
kvm_run returned -22
rax 0000000000000010 rbx 0000000000000080 rcx 0000000000000000 rdx 0000000000000080
rsi 000000000025db2a rdi 000000000007db2a rsp 0000000000000200 rbp........
yum -y install fail2ban
vi /etc/fail2ban/jail.conf
[asterisk-tcp]
enabled = true
filter = asterisk
action = iptables-multiport[name=asterisk-tcp, port="5060,5061", protocol=tcp]
sendmail-whois[name=Asterisk, dest=you@example.com, sender=fail2ban@example.com]
logpath = /var/log/asterisk/messages
maxret........
I chose this because I heard a lot of stories about scams and that many providers I contacted said they can't unlock the Canadian I717s (one said "my Bell server" is down).
This method worked perfectly on my Bell I717M and should work for all I717 in Canada, I was able to insert a foreign SIMcard. This will work abroad too but remember entering CWM mode is different for I717's in other countries (at least theUS).
Step 1 - Root + CWM........
I don't expect this to be solved soon but some of Yahoo's DNS servers are out of whack. I changed the IPs of some nameservers of some domains and now most Yahoo users can't e-mail to those domains!
As you can see below by the "No MX or A records for mychangedomain.com", now Yahoo's DNS/mailserver DNS cache is wrong. You would think they would at least have cached the old incorrect records, but instead for some reason their DNS cache has no entry and doesn't seem........