Cisco 2960 Switch Reset To Factory Defaults

*The easy way is to just hold the mode button for 10+ seconds.

The full/proper way is below:

1.) Either power on the unit and hold the "mode" button or hold the "mode" button until you see the below:

00:04:08: %SYS-7-NV_BLOCK_INIT: Initalized the geometry of nvram
00:04:08: %EXPRESS_SETUP-6-CONFIG_IS_RESET: The configuration is reset and the system will now reboot
00:04:09: %SYS-5-RELOAD: Reload requested Reload Reason: power-on.
Base ethernet MAC Address: 00:1a:a2:4e:6a:00
Xmodem file system is available.
The password-recovery mechanism is enabled.
Initializing Flash...
flashfs[0]: filesystem check interrupted!
...done Initializing Flash.
Boot Sector Filesystem (bs) installed, fsid: 3

The system has been interrupted, or encountered an error
during initializion of the flash filesystem.  The following
commands will initialize the flash filesystem, and finish
loading the operating system software:

    flash_init
    load_helper
    boot

2.) Initialize the flash by typing "flash_init"


switch: flash_init
Initializing Flash...
flashfs[0]: 600 files, 19 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 32514048
flashfs[0]: Bytes used: 7713280
flashfs[0]: Bytes available: 24800768
flashfs[0]: flashfs fsck took 10 seconds.
...done Initializing Flash.
Setting console baud rate to 9600...

3.) Delete config files

del flash:config.text
Are you sure you want to delete "flash:config.text" (y/n)?y
File "flash:config.text" deleted

del flash:vlan.dat
Are you sure you want to delete "flash:vlan.dat" (y/n)?y
File "flash:vlan.dat" deleted

 

4.) boot!

boot

 

 


Cisco IOS Software, C2960 Software (C2960-LANBASE-M), Version 12.2(25)SEE2, RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2006 by Cisco Systems, Inc.
Compiled Fri 28-Jul-06 04:33 by yenanh
Image text-base: 0x00003000, data-base: 0x00AA2F34

Initializing flashfs...

flashfs[1]: 600 files, 19 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 32514048
flashfs[1]: Bytes used: 7713280
flashfs[1]: Bytes available: 24800768
flashfs[1]: flashfs fsck took 1 seconds.
flashfs[1]: Initialization complete....done Initializing flashfs.

POST: CPU MIC register Tests : Begin
POST: CPU MIC register Tests : End, Status Passed

POST: PortASIC Memory Tests : Begin
POST: PortASIC Memory Tests : End, Status Passed

POST: CPU MIC PortASIC interface Loopback Tests : Begin
POST: CPU MIC PortASIC interface Loopback Tests : End, Status Passed

POST: PortASIC RingLoopback Tests : Begin
POST: PortASIC RingLoopback Tests : End, Status Passed


Tags:

cisco, reset, factory, defaults, quot, mode, sys, nv_block_init, initalized, geometry, nvram, express_setup, config_is_reset, configuration, reboot, reload, requested, ethernet, xmodem, password, mechanism, enabled, initializing, flashfs, filesystem, interrupted, sector, bs, installed, fsid, encountered, initializion, commands, initialize, loading, operating, software, flash_init, load_helper, typing, directories, orphaned, bytes, fsck, console, baud, delete, config, text, deleted, vlan, dat, ios, lanbase, fc, copyright, inc, compiled, fri, jul, yenanh, aa, initialization, cpu, mic, register, portasic, interface, loopback, ringloopback,

Latest Articles

  • Linux qemu-kvm How To Enable Soundcard in Guestl
  • QEMU-KVM Windows and Server Guest Installs Mouse Tracking Pointer Location Solution
  • SSH Keep Alive To stop Disconnections
  • Linux How To Disable SATA NCQ For Better Performance
  • the sign-in method you're trying to use isn't allowed. For more info, contact your network administrator - solution for active directory
  • gsmartcontrol for Windows to Check the SMART S.M.A.R.T status
  • WebRTC Vulnerability Shows Local IP Address Even When Using a Proxy or VPN Firefox Fix And Disable Solution
  • chroot in Linux Howto Simple and Easy Guide
  • qemu-kvm qemu-system Image format was not specified for '/mnt/space/cucm12.img' and probing guessed raw. Automatically detecting the format is dangerous for raw images, write operations on block 0 will be restricted. Specify the 'ra
  • Linux Over VNC VMWare How To Switch Virtual Terminals Console Without Using Ctrl+Alt+F1
  • Skype For Business 2015 and 2019 Guide, Reference, Howto and Troubleshooting Solutions
  • Centos 6 or 7 no DHCP IP during startup on first boot or reboot solution
  • Debian / Mint / Ubuntu net-tools packages provides netstat, ifconfig, route, arp and other classic network admin tools
  • Linux Mint XWindows Ubuntu MATE or Cinnamon How To Restart The GUI / Graphics / Session if it freezes without losing current windows or programs
  • Linux bash prompt why does it not show username@host and the current directory?
  • Microsoft SQL Server Check What Version is Running
  • How to install and setup LXC Containers (OpenVZ alternative) on Centos 6 / 7
  • Cisco CUCM Unified Communication Manager Howto Guide and Tutorials
  • SSH persistent and automatic login script for proxy
  • SSH proxy/command in the background or from cron script