• Cisco Unified Communications Manager 12 Install Errors on Proxmox/KVM


    The strange thing is that usually the first install or two will work on any new machine but then it suddenly won't. I had this experience on QEMU 2.13 on a different machine. There is something finicky or buggy about the CUCM installer even when choosing the same virtual hardware specs. qemu-kvm command: /usr/libexec/qemu-kvm -version QEMU PC emulator version 0.12.1 (qemu-kvm-0.12.1.2-2.506.el6_10.1), Copyright (c) 2003-2008 Fabrice Bellard ........
  • Cisco 2960 Switch Reset To Factory Defaults


    *The easy way is to just hold the mode button for 10+ seconds. The full/proper way is below: 1.) Either power on the unit and hold the "mode" button or hold the "mode" button until you see the below: 00:04:08: %SYS-7-NV_BLOCK_INIT: Initalized the geometry of nvram 00:04:08: %EXPRESS_SETUP-6-CONFIG_IS_RESET: The configuration is reset and the system will now reboot 00:04:09: %SYS-5-REL........
  • VBOX VirtualBox How To Import Raw .img Disk File


    What you need to do if you have taken a dd or real raw image dump of a hard disk: VBoxManage convertdd windows2019-eval-template.img windows2019.vdi --format VDI The .img is the raw dd dump and the .vdi is the output file. --format VDIspecifies to output to .vdi format If you are in a pinch you can always use qemu-kvm binary and manually specify the .img as your disk and i........
  • Linux How To Create A RamDisk


    size = the amount of RAM (m for megabytes) /mnt/ram = the mount location of the ram disk (change to the path you want it mounted to) mount -t tmpfs -o size=4096m tmpfs /mnt/ram/ Example test in an old server: You can see that when reading if you don't specify bs1=M the read speeds are several times slower (eg. 450MB/s vs 2.1GB/s) mount -t tmpfs -o size=4096m tmpfs /mnt/ram/^C root@testserver:~# dd........
  • Linux wlan0 check all wireless clients


    iw dev wlan0 station dump This is very useful because it is helpful if you are running something like hostapd and need to see the signal strength and negotiated connection speed. Station ff:ff:ff:ff:ff:ff (on wlan0) inactive time: 16309 ms rx bytes: 25451 rx packets: 325 tx bytes: 44381 tx packets: 159 tx retries: 0 tx failed: 0 signal: -72 [-72] dBm signal avg: -72 [-72] dBm........
  • Linux use growisofs to burn a larger file on a BD-R / Bluray Disc


    growisofs -Z /dev/sr0 critical.tar.gz.gpg Executing 'genisoimage critical.tar.gz.gpg | builtin_dd of=/dev/sr0 obs=32k seek=0' I: -input-charset not specified, using utf-8 (detected in locale settings) File critical.tar.gz.gpg is larger than 4GiB-1. -allow-limited-size was not specified. There is no way do represent this file size. Aborting. :-( write failed: Input/output error #remember to us........
  • Linux partprobe/partx cannot access last and 4th partition


    On a test machine Iwas never able to access to a newly created 4th partiton. As we can see there are dev devices for everything but the 4th partition. The normal "partprobe" or "kpartx" or kernel being told to rescan the block device didn't help (only a reboot did). fdisk -l /dev/sda Disk /dev/sda: 750.2 GB, 750156374016 bytes 255 heads, 63 sectors/track, 91201 cylinders Units........
  • mdadm: add new device failed for /dev/sdb4 as 3: Invalid argument solution


    mdadm --manage /dev/md125 -a /dev/sdb4 mdadm: add new device failed for /dev/sdb4 as 3: Invalid argument Dec 19 01:23:48 storageboxtest kernel: [ 2328.854491] md: sdb4 does not have a valid v1.2 superblock, not importing! Dec 19 01:23:48 storageboxtest kernel: [ 2328.854499] md: md_import_device returned -22 #zero the superblock and try again! mdadm --zero-superblock /dev/sdb4 mdadm --ma........
  • Why SMART is not smart at all and doesn't properly predict disk errors that cause a kernel panic or crash


    Before getting into the output here is my typical experience with SMART, there is what I call a "bad disk" with pending and uncorrectable sectors that cannot be reallocated. It has caused a kernel panic and system crash repeatedly as we can see from the logs. But SMART says it has "PASSED" its self assessment. SMART is still useful to me but it is more about looking at Current_Pending_Sector. Any time I have had anything but 0 for that attribute it........
  • vmkping -I vmk1 10.0.2.69 PING 10.0.2.69 (10.0.2.69): 56 data bytes sendto() failed (Host is down)


    [root@localhost:~] vmkping -I vmk1 10.0.2.69 PING 10.0.2.69 (10.0.2.69): 56 data bytes sendto() failed (Host is down) vsphere distributed switch vmotion not working [root@localhost:~] esxcfg-route -l VMkernel Routes: Network Netmask Gateway Interface&........
  • Debian Mint Ubuntu compiling xmr-stak


    sudo apt-get install libcurl4-openssl-dev git build-essential autotools-dev autoconf libcurl3 sudo apt-get install libcurl4-gnutls-dev git clone https://github.com/wolf9466/cpuminer-multi sudo apt-get install cmake libpthread-* libmicrohttpd-dev libssl-dev libhwloc-dev git clone https://github.com/fireice-uk/xmr-stak-cpu.git make install cd bin chmod +x xmr-stak-cpu ./xmr-stak -O xmr........
  • Ethereum Client Errors


    INFO [07-19|12:11:51] Imported new block receipts count=590 elapsed=8.440s bytes=74117699 number=4870906 hash=6bc60b…934753 ignored=0 INFO [07-19|12:11:57] Imported new state entries count=499 elapsed=9.963ms processed=71076 pending=1526 retry=2&nbs........
  • wodim / cdrecord error cannot burn DVD or BDR .iso Errno: 5 (Input/output error), write_g1 scsi sendcmd: no error


    dvd+rw-mediainfo /dev/sr0 INQUIRY: [ASUS ][BW-16D1HT ][3.00] GET [CURRENT] CONFIGURATION: Mounted Media: 11h, DVD-R Sequential Media ID: RITEKF1&n........
  • vino server error cannot login


    10/07/2018 03:05:14 PM [IPv4] Got connection from client10.10.25.1 10/07/2018 03:05:14 PM other clients: 10/07/2018 03:05:14 PM Client Protocol Version 3.7 10/07/2018 03:05:14 PM Advertising security type 18 10/07/2018 03:05:14 PM Client returned security type 18 10/07/2018 03:05:14 PM TLS Handshake failed: Could not negotiate a supported cipher suite. 10/07/2018 03:05:14 PM Client10.10.25.1 gone 10/07/2018 03:05:14 PM Statistics:........
  • OpenVPN cannot ping remote IP routing loop issue after connecting


    Sometimes if you have a very basic configuration OpenVPN on the client side for some reason sends all traffic to the OpenVPN server IP through the tun0 which is of course impossible and creates a block or routing loop. This is because you need to use your normal ISP/LANgateway to hit the OpenVPN server if it is remote/offsite as is usually the case. So if you are connected to the OpenVPN through say a tun0 device and your routing is set to connect to the OpenVPN&nbs........
  • How To Turn Any .iso file into a bootable USB drive


    This works for almost all ISO's Ifind (at least Linux based): sudo dd if=CentOS-6.9-x86_64-minimal.iso of=/dev/sdg bs=20M 20+1 records in 20+1 records out 427819008 bytes (428 MB) copied, 118.233 s, 3.6 MB/s Of course change the .iso filename above and the /dev/sdg to your desired USB drive!........
  • MySQL Maximum INT Size Truncation Issue/Warning


    MySQL will silently truncate a larger INT than capable. Check MySQL's own documentation here: As we can see the maximum size of INT (which is the most commonly used) is 2147483647 A lot of coders make this mistake by using very large values such as 9999999999 but it would actually truncate to 2147483647 which is the maximum size of an INT. This is dangerous beca........
  • Linux how to copy GPT partition table with dd


    The old MBR 512 bytes partition table is no longer valid if you are using GPT. To copy a GPT table with dd to another disk do it like so: Below sda is the source disk and destination disk is sdb (change to meet your needs). dd if=/dev/sda of=/dev/sdb bs=1536 count=1 You can also use dd to backup your partition table like normal but with the bs of 1536 dd........
  • USB 3.0 PCI x1 Card Review VIA VL805 on Linux Review and Experience


    This is a VIA made VL805 USB 3.0 Chipset with 4-ports and MOLEX powered. First of all this unit was cheap at about only 9 USD with fast shipping. My biggest concern was if this was a quality unit and would it really give you full USB 3.0 speeds (some people reported with similar cards that for some weird r........
  • Openshot 2.2 is very unstable always crashing in Linux Mint 18.1!


    Jun 1 15:45:42 videoeditor-desktop org.mate.panel.applet.MintMenuAppletFactory[1882]: project_data:INFO Missing folder chosen by user: Jun 1 15:45:42 videoeditor-desktop org.mate.panel.applet.MintMenuAppletFactory[1882]: project_data:INFO Removed missing file: MAH02949.MP4 Jun 1 15:45:57 videoeditor-desktop org.mate.panel.applet.MintMenuAppletFactory[1882]: ui_util:WARNING Icon theme media-playback-start not found. Will use backup........
  • Track 01: 34 of 1726 MB written (fifo 100%) [buf 99%] 3.6x.Errno: 5 (Input/output error), write_g1 scsi sendcmd: cmd timeout after 1.897 (40) s CDB: 2A 00 00 00 44 A9 00 00 1F 00 resid: 6144 cmd finished after 1.897s timeout 40s write track da


    These errors believe it or not are simply because of not being the root user or running with sudo! However if you didn't know to try as root you'd think there was a problem with your burner or disc Essentially it looks like without root you cannot send the required scsi commands to continue writing. Ithink cdrecord should have built-in tests or safeguards to see if it has the permissions to run the required commands. I guess for more advanced users the idea is simila........
  • Using a proxy with yum in Centos 6


    Could not retrieve mirrorlist http://mirrorlist.centos.org/?release=6&arch=x86_64&repo=os error was 12: Timeout on http://mirrorlist.centos.org/?release=6&arch=x86_64&repo=os: (28, 'Operation too slow. Less than 1 bytes/sec transfered the last 30 seconds') Error: Cannot find a valid baseurl for repo: base You would think this should be fine and simple like using a proxy with most other software? However........
  • ERROR 2013 (HY000): Lost connection to MySQL server during query


    The solution is simple but strange, if you copy your /var/lib/mysql directory to another server and think it will work, be sure to check if you have /var/log/mysql and binary log files. If you do, the server will not work and will give you errors like below and crash without the proper log files. UPDATE user SET password=password("newpass") WHERE user='root'; flush privileges; ERROR 2013 (HY000): Lost connection to MySQL server durin........
  • ADATA SU800 256GB 3D NAND Flash SSD Test & Review


    I keep reading these drives are slower, but they are cheap and still SSDand work very fast for my needs. As you can see the sequential read is 481-491MB/s, if I put them in MDADM RAID10 mode (normal RAID1) they should give me well over 900MB/s and with redundancy and being very cheap for what they offer. [1232206.315622] scsi 8:0:1:0: Direct-Access ATA ADATA SU800&........
  • remove gpt partition linux


    sudo fdisk /dev/sdh WARNING: GPT (GUID Partition Table) detected on '/dev/sdh'! The util fdisk doesn't support GPT. Use GNU Parted. WARNING: The size of this disk is 8.0 TB (8001563221504 bytes). DOS partition table format can not be used on drives for volumes larger than (2199023255040 bytes) for 512-byte sectors. Use parted(1) and GUID partition table format (GPT). The device presents a l........
  • mdadm mirrored RAID1 performance using RAID10 -f2 (Far Layout) is the solution


    The only way I've found in mdadm to make 2 drives perform like a proper RAID 1 (eg. the read speed should be 2x that of a single drive) is to use the --layout=f2 (far 2). mdadm raid10 performance issues. Be very aware that mdadm seems to default to layout=n2 (which means near). In this scenario it means it is like mdadm RAID 1 performance (you get maximum read speeds of a single drive). dd if=/dev/md126 of=/dev/null bs=1M cou........
  • Centos installing grub problems suspect gpt problem


    grub> root (hd0,0) root (hd0,0) Filesystem type is ext2fs, partition type 0xfd grub> setup (hd0) setup (hd0) But if you do: root (hd1,0) setup (hd1) it does work, I think hd0/sda had a GPT partition that was not removed properly (what I did was just dd bs=512 count=1 the partition table from another drive since the partition table should be identical). Checking if "/boot/grub/........
  • How to manually mount Linux disk image partition without using losetup


    In this case we want to mount partition #2 fdisk -lu Centos-6.6-x86_64.img You must set cylinders. You can do this from the extra functions menu. Disk Centos-6.6-x86_64.img: 0 MB, 0 bytes 255 heads, 63 sectors/track, 0 cylinders, total 0 sectors Units = sectors of 1 * 512 = 512 bytes Device Boot&nbs........
  • Debian 8 Jessie in Linux OpenVZ Container does not work on Centos host


    It sounds like this is corrected in later versions of the OpenVZ kernel but Iam not sure, it may also be that a much newer kernel is needed and Centos may not have a recent enough kernel. *Debain 7.0 however does work fine as a temporary fix or work around. Debian 8 OpenVZ no IP and networking not working: lo Link encap:Local Loopback  ........
  • Centos 6 how to guide convert LVM non-RAID into mdadm 1/10 RAID array live without reinstalling


    Here is the scenario you or a client have a remote machine that was installed as a standard/default minimal Centos 6.x machine on a single disk with LVM for whatever reason. Often many people do not know how to install it to a RAID array so it is common to have this problem and why reinstall if you don't need to? In some cases on a remote system you can't easily reinstall without physical or KVM access. So in this case you add a second physical or disk or already ha........
  • openvz yum problem Centos 6.5 cannot find file on mirror:


    #solution Edit /etc/yum.repos.d/openvz.repo For the first two entries comment out #mirrorlist and uncomment #baseurl and then it worked openvz yum problem Centos 6.5 cannot find file on mirror: yum update Loaded plugins: fastestmirror Determining fastest mirrors * openvz-kernel-rhel6: mirrors.ustc.edu.cn * openvz-utils: mirrors.ustc.edu.cn base ........
  • HP Procurve Switch 2824 CLI Telnet Experience , Guide and Tutorial


    telnet 192.168.1.54 ------------------------------------- ProCurve J4903A Switch 2824 Software revision I.10.77 Copyright (C) 1991-2009 Hewlett-Packard Co. All Rights Reserved. RESTRICTED RIGHTS LEGEND Use, duplication, or disclosure by the Government is subject........
  • Dell CS24-NV7 lspci dmidecode info


    0000:00:00.0 RAM memory: NVIDIA Corporation MCP55 Memory Controller (rev a2) 0000:00:01.0 ISA bridge: NVIDIA Corporation MCP55 LPC Bridge (rev a3) 0000:00:01.1 SMBus: NVIDIA Corporation MCP55 SMBus (rev a3) 0000:00:02.0 USB controller: NVIDIA Corporation MCP55 USB Controller (rev a1) 0000:00:02.1 USB controller: NVIDIA Corporation MCP55 USB Controller (rev a2) 0000:00:05.0 IDE interface: NVIDIA Corporation MCP55 SATA Controller (rev a3) 0000:00:05.1 I........
  • bash check size of file using stat


    stat -c %s testfile.zip 10000000 The output is shown above in bytes. ........
  • Lost connection to MySQL server during query [2013]


    This happened while trying to delete several thousand users from phpBB and basically corrupted the innoDB tables. InnoDB: Page lsn 3 881164362, low 4 bytes of lsn at page end 881164362 InnoDB: Page number (if stored to page already) 86920, InnoDB: space id (if created with >= MySQL-4.1.1 and stored already) 0 InnoDB: Page may be an index page where index id is 700 InnoDB: (index "tid_post_time" of table "phpBBdb2005"."phpbb3_p........
  • libguestfs tools howto guide for managing virtual machine images


    libguestfs tools howto guide for managing virtual machine images To mount a partition #mount the kvmuser102821.img image and the /dev/sda1 partition from it to the local directory "mount" guestmount -a kvmuser102821.img -m /dev/sda1 mount To list partition info on the image: virt-df image.img Filesystem........
  • drbd won't create device if previous partition is on it Command 'drbdmeta 0 v08 /dev/md160 internal create-md' terminated with exit code 40


    This is what fixed it: [root@box13 ~]# dd if=/dev/zero of=/dev/md160 bs=512 count=500 Basically you need to wipe out more than just the 512 byte partition table so 512 bytes * 500 is more than enough to make DRBD happy and think the partition is now empty. The reason this happens is because it gets confused when there is a previous partition with data on the device you are using. root@box13 ~]# d........
  • Fatal error: Out of memory (allocated 6291456) (tried to allocate 7680 bytes)


    Fatal error: Out of memory (allocated 6291456) (tried to allocate 7680 bytes) This is usually caused by Wordpress, Drupal or other ridiculously inefficient CMS' out there, as a temporary fix you can increase PHP's memory limit but it's best to find the actual culprit, by disabling add-ons and other scripts etc...........
  • sudo: sorry, you must have a tty to run sudo solution


    ./rsync.sh sudo: sorry, you must have a tty to run sudo rsync: connection unexpectedly closed (0 bytes received so far) [sender] rsync error: error in rsync protocol data stream (code 12) at io.c(601) [sender=3.0.7] Solution edit /etc/sudoers #Defaults requiretty........
  • bash check that file is not blank/zero bytes in size


    if [ ! -s /path/to/file ]; then echo "file is blank or zero bytes" fi Use -s to check if it's larger than 0 bytes, Ilike to use the ! (not) operator to do this as shown above.........
  • CPanel suhosin install failed


    /scripts/phpextensionmgr install PHPSuHosin Updating md5sum list Fetching http://httpupdate.cpanel.net/cpanelsync/easy/targz.yaml (connected:0).......(request attempt 1/12)...Resolving httpupdate.cpanel.net...(resolve attempt 1/65)... Fetching http://httpupdate.cpanel.net/mirror_addr_list (connected:0).......(request attempt 1/3)......connecting to 74.50.120.123...@74.50.120.123......connected......receiving...100%......request success......Done........
  • Dell FS12-NV7 2U Server Information and Guide


    I've got one of these for testing projects from work at home and got more than I bargained for with the time I've spent on it due to the storage handing/Perc 6/i cards. My particular model came with the following: 2U Rack Mount Server with Rails 2xOpteron 2373 EE (Quad Core, there is a 6-core version that can be found at times) 16GB RAM 2 x 250GB Seagate SATA 2 x Dell Perc 6/i (horrible and a nightmare to work........
  • Dell Perc 6/i SATA benchmarks without battery


    The results are not bad, the Hitachi performs the same as it does in a SATA2 motherboard. However, the 2TB is much different, on a similar 2TB Toshiba I get about 198MB/s on a different motherboard vs the 2TB Hitachi which should produce similar results. This Dell Perc 6/i is on a PCI x8 riser card and is connected to a 12-port backplane. Adapter #0 Enclosure Device ID: 32 Slot Number: 0 Enclosure position: N/A De........
  • WD 20EARX Dead Again


    Another new drive bad from the start: Jun 2 15:14:18 one-desktop kernel: [15895.386779] ata2.00: exception Emask 0x50 SAct 0x1 SErr 0x280900 action 0x6 frozen Jun 2 15:14:18 one-desktop kernel: [15895.386782] ata2.00: irq_stat 0x08000000, interface fatal error Jun 2 15:14:18 one-desktop kernel: [15895.386784] ata2: SError: { UnrecovData HostInt 10B8B BadCRC } Jun 2 15:14:18 one-desktop kernel: [15895.386788] ata2.00: cmd 60/0........
  • WD 20EARX 2TB Bad within days


    This is just trying to read 5GB off the drive with dd and the drive initially tested ok but shortly after I wondered why I was seeing 2MB/s read speeds. Notice the "current_pending_sector", anytime I've seen it at anything above 0 even with no other bad fields/attributes, it means the drive is bad. ata1.00: exception Emask 0x0 SAct 0x3 SErr 0x0 action 0x0 ata1.00: irq_stat 0x40000008 ata1.00: failed command: READ FPDMA QUEUED ata1.00: cmd 60/00:00:........
  • eth0 changed to eth1 or eth2 and the solution to fix it


    If you move your hard drive(s) around to other computers/servers, you'll find that your eth0 keeps getting higher, the first time it will become eth1 and then eth2 etc and even higher if your server has dual or quad NICs. The reason is that udevd basically assigns eth0 tot he first NIC it finds and remembers it, if it encounters a NIC with a differentMAC, it assigns it one higher (eg. eth1). See the example below, I have eth2 now so how doI fix it?........
  • Bad Hard Drive Slows Down Computer


    Here's a proven example of what a bad hard drive can do, it was technically functioning OKin a RAID array but the system became extremely low and the load become high and IOWAIT was even higher and I always thought it was a bad application. The truth is that this failing 1TBHitachi has slowly gotten worse and caused huge slowdowns, (eg. 100% load on Thunderbird waiting for e-mails to load etc..). After swapping it out, tabs change instantly, emails are not lagged, and........
  • Hitachi Serial Numbers for Hard Drives without seeing the physical drive


    Here's what SMART tells me the serial number is: === START OF INFORMATION SECTION === Device Model: Hitachi HDS721010CLA332 Serial Number: JP2940HQ3ZY7KH Firmware Version: JP4OA3EA User Capacity: 1,000,204,886,016 bytes Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 8 ATA Standard is:&nb........
  • Samsung Galaxy Note ICS Corrupting microSDHC partition table?


    This was partitioned as a single 32GB VFAT but when I inserted it into the phone it said that it can't read it and now here is how the partition table looks. Interestingly enough the data works and reads fine from the computer still. Disk /dev/sdb1: 32.1 GB, 32085360640 bytes 64 heads, 32 sectors/track, 30598 cylinders, total 62666720 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum........
  • kvm cannot boot xen guest using lvm


    This booting error is because the Xen PV guest image uses the Xen kernel, this is not compatible with anything but a host running a Xen kernel. I did a kpartx -av virtual.img and then it created some partitions that showed up in fdisk. I mounted it and did a chroot into it and removed the xen kernel and installed a normal kernel but Xen still shows the same kernel in Grub (only the Xen one). This is strange but it seems like this Xen PV guest has some sort of hidden or........
  • Nearly 100% CPU Usage from processes called dma0chan0 dma0chan1 dma0chan2 dma0chan3


    Inever started these processes but they are from a custom based bootable Linux I've made and I've never seen this behavior on other machines or even with the same machine using different kernels. These processes seemed to spawn on their own and I have no idea why and even worse why the CPU usage is so high? Here's the output from top: 907 extaudit 30 10 0 0 0 R 90.7 0.0........
  • lvm resize and use the remaining extra space


    df -h Filesystem Size Used Avail Use% Mounted on /dev/mapper/vg_12-lv_root 50G 1.2G 46G 3% / tmpfs 7.8G 0&nb........
  • Thunderbird How-To Copy/Backup/Restore Accounts and Settings to Another Computer


    The best way is to use rsync, I've set it up so it doesn't copy unnecessary files, or at least ones I'm sure aren't needed. Here is the rsync command Iused (adapt to your specific Thunderbird profile location): rsync -hazv user@remotehost.com:/home/user/.thunderbird/sbrer.default/* /home/user/.thunderbird/4nyb0.default/ --exclude=global* --exclude=Cache --exclude=ImapMail --exclude=Mail This is a great way to get your e-mail accounts going on a new c........
  • mdadm: /dev/sdb1 not large enough to join array solution


    mdadm --manage /dev/md1 --add /dev/sdb1 mdadm: metadata format 00.90 unknown, ignored. mdadm: metadata format 00.90 unknown, ignored. mdadm: metadata format 00.90 unknown, ignored. mdadm: /dev/sdb1 not large enough to join array md1's first primary member /dev/sda3 has 57394 cylinders while the /dev/sdb1 has 57393 (1 less cylinder) which is why it won't work. fdisk -l /dev/sda3 Disk /dev/sda3: 47........
  • How to mount/access a single partition from dd image with Linux


    parted sdc.img GNU Parted 1.8.8 Using /home/one/sdc.img Welcome to GNU Parted! Type 'help' to view a list of commands. (parted) unit&nb........
  • ip_conntrack: table full, dropping packet. solution for Linux RHEL/Centos/Debian


    ip_conntrack: table full, dropping packet. A lot of clients I've seen have this issue, it really seems the default level is way too small. Once this connection tracking table becomes full then packets get dropped which is obviously a bad thing. One thing to be mindful of though is that 350 bytes of memory are used per entry so there is some justification for not keeping it too high. However, if you have multiple servers running or high traffic daemons........
  • How to view an EFI GPT partition in Linux


    Disk /dev/sda: 320.0 GB, 320072933376 bytes 256 heads, 63 sectors/track, 38761 cylinders Units = cylinders of 16128 * 512 = 8257536 bytes Device Boot Start End Blocks Id System /dev/sda1 1 38........
  • Windows Secret Hidden Temp Directory to free out of disk space issues


    Replace "Administrator" with your username. C:Documents and SettingsAdministratorLocal SettingsTemp Ihave often found several gigabytes of temporary files in there! Just be warned that they may not all be deletable if the files are being used by open programs (so close everything you can). This helped me in a pinch many times when for apparently no reason gigs of disk space are being used for an unknown reason.........
  • Xen how to mount disk images off-line and access data


    fdisk -lu VPS.img last_lba(): I don't know how to handle files with mode 81ed You must set cylinders. You can do this from the extra functions menu. Disk VPS.img: 0 MB, 0 bytes 255 heads, 63 sectors/track, 0 cylinders, total 0 sectors Units = sectors of 1 * 512 = 512 bytes Device Boot Start End ........
  • How To Burn ISO Image using cdrtools/dvdrtools for Linux/Unix Ubuntu/Debian/RHEL/Centos etc..


    It really is as simple as: cdrecord -v dev=/dev/sr0 pathtoyourisoimage.iso -v is for verbose, I prefer it but if you don't you won't see as much output like below (I like to know the details and exactly what's happening) dev=/dev/sr0 specifies the device name of your burner (they say not to use it and to specify some weird annoying device string but using the raw /dev has always worked for me and is how it should have been implemented from the start IMHO)........
  • How To Test If Your Hard Drive Is Good/Signs of dying hard drive


    I like dd, although it only reads it, usually a read test of the entire disk will uncover if your hard drive is bad in some parts. This is a good thing to do at least once a month, a lot of times bizarre program behavior, laginess and crashing/unnmounting problems etc.. are due to a failing disc and SMART won't know it or indicate a problem: We must also remember there's never a guarantee, I've found that ever since we moved to larger and more platters per drive with 1TB drives........
  • smart is not smart, it thinks a dead drive is still good


    I had a dying drive that smart thought until it totally disappeared was a good drive, and actually all parameters did look fine but this system was causing my system to lockup and other bad behavior: === START OF INFORMATION SECTION === Device Model: WDC WD20EARS-00MVWB0 Serial Number: WD-WMAZ20139 Firmware Version: 50.0AB50 User Capacity: 2,000,398,934,016 bytes Device........
  • Hitachi 2TB HDS5C3020ALA632 drive DOA


    I had one of these shipped and it was not recognized when plugged in, here's what a dead drive looks like (I assume it's teh circuit board which is dead): ata1: link is slow to respond, please be patient (ready=0) ata1: softreset failed (device not ready) ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata1: link online but device misclassified, retrying ata1: link is slow to respond, please be patient (ready=0) ata1: softreset f........
  • Apache High CPU Usage Enable Mod_Status Guide Solution - Find Cause of High CPU Usage Script/Domain


    mod_status is a great way to track down the source of high CPU usage and to find what vhost/script is the cause of it. It gives you a live view of bandwith usage, CPU usage, and memory usage broken down by domain/vhost and script/URI. Enable mod_status vi /etc/httpd/conf/httpd.conf ExtendedStatus On SetHandler server-status Order Deny,Allow Deny from all All........
  • Enable SPAMASSASSIN on Postfix in 5 minutes


    Centos 5 Postfix and SPAMASSASSIN Tutorial yum install spamassassin chkconfig spamassassin on vi /etc/mail/spamassassin/local.cf ############## #required_hits 5 #report_safe 0 #rewrite_header Subject [SPAM] #5 is the least restrictive (means only the most obvious SPAM is caught. 0 is obviously the most restrictive/sensitive and would have lots of false positives require........
  • CPU #1 not responding - cannot use it.


    I think this will be useful to others because I have a server that kept crashing mysteriously during intense disk usage/RAID checks. It would only crash during the weekly RAID integrity check. ThenI noticed during a reboot that not all CPUs were being brought up, as a result this actually creates much higher temperatures with the output I got from sensors, just booting the system produced higher than normal temperatures. You can imagine that a full blown RAID check........
  • Linux Realtek Gigabit NIC huge/high latency problem after sleep?


    That is pinging to the gateway IP on the same switch, the same IP is pingable externally without any problems which makes me think the switch is fine. 64 bytes from 55.55.55.55: icmp_seq=4 ttl=255 time=1.07 ms 64 bytes from 55.55.55.55: icmp_seq=1 ttl=255 time=3536 ms 64 bytes from 55.55.55.55: icmp_seq=2 ttl=255 time=2536 ms 64 bytes from 55.55.55.55: icmp_seq=3 ttl=255 time=1536 ms 64 bytes from 55.55.55.55: icmp_seq=8 ttl=255 time=1.20 ms 64 by........
  • WD EARS Advanced Format Can't be fixed?


    There's no partial WD EARS alignment fix: I had data on /dev/sda3 and /dev/sdb3 (RAID1) so I couldn't edit that one. I thought I'd be smart and try fixing the first two partitions so I set the first one starting at sector 2048 and then +8 for the second partition. This has really slowed the performance down worse than it ever was! Disk /dev/sda: 2000.4 GB, 2000398934016 bytes 255 heads, 63 sectors/track, 243201 cylinders, tot........
  • mdadm RAID 1 adventures


    I separated the 2 drives in the RAID 1 array. 1 is the old one /dev/sda and is out of date, while the separated other one /dev/sdc was in another drive and mounted and used with more data (updated). I wonder how mdadm will handle this: usb-storage: device scan complete md: md127 stopped. md: bind md: md127: raid array is not clean -- starting background reconstruction raid1: raid set md127 active with 1 out of 2 m........
  • WD (Western Digital) Advanced Format Drive Lagged/Slow Speed/Performance/Design Flaw EAD/EARS problem WDC WD20EARS-00S8B1


    Let the numbers speak for themselves, from what I read the Load_Cycle_Count which is very high (more than 500,000/half a million times) is the number of head parks. What a stupid"Green" design and design flaw which will probably mean an early life for the drive. This is almost as silly as Seagate's new reputation for BSY/poor quality disks since the 7200.11 series. To make it worse this is also when Western Digital introduced "Advanced Format" o........
  • PHP Email Attachment Corrupt Solution


    I couldn't figure out why this wouldn't work, a test script in the root of my htdocs folder worked fine. Within some subdirectories the same code would produce different base64 results but I didn't know hwy. Archive: /tmp/archive.zip Zip file size: 6888 bytes, number of entries: 92 error [/tmp/archive.zip]: missing 242827681 bytes in zipfile (attempting to process anyway) error [/tmp/archive.zip]: attempt........
  • Linux Burn MP3 CD On the Fly using


    I finally decided to look into some utils that did this, and the first one I found is "mp3burn". It is unbelievable simple and perfect. *2017-11 update and mp3burn is still available in standard repos such as Ubuntu 14/16 so this is a current and working project. Just install the package and it gets all required libraries to convert and then burn's on the fly. And you won't believe how simple it is. I just want to a directory that had the MP3's I wanted t........
  • mdadm: /dev/sda1 is too small: 0K - solution


    I was creating a RAID array and got this error: mdadm: /dev/sda1 is too small: 0K mdadm: create aborted Of course sda1 is not too small, both partitions sda1 and sdb1 are identical in size: Disk /dev/sda: 2000.3 GB, 2000398934016 bytes 255 heads, 63 sectors/track, 243201 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x00000000 Device Boot Sta........
  • mdadm can you downgrade the superblock?


    Why would you want to downgrade the superblock? Old mdadm verisons like mdadm 2.5.6 only use the 0.90 superblock/metadata and new versions use 1,1.0,1.1 and 1.2 superblocks by default. There are some annoying caveats with this, first of all the new superblocks (later than 0.90) CANNOT be read by GRUB, so you won't even be able to install GRUB. Even worse, old versions of mdadm CANNOT automatically detect arrays even if they were created with a new version of mdadm with th........
  • Seagate Drive 500GB Drive Dying


    This drive is clearly on the way out, the Kernel knows it but I'm surprised that SMART is not concerned. I didn't blame Seagate for their past issues until now. This hard drive has hardly been used and has not even been powered on for a year according to SMART. Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.11 Device........
  • Seagate 7200.11 firmware defect in 500GB, 1000GB (1TB) and 1500GB (1.5TB) Hard Drives


    Seagate Inventory/Firmware Check I heard about this issue a long time ago but never looked into it. I figured I wasn't affected since my 500GB drives were running for so long. I've been using Seagate's since 2002 and to this day all of the drives I have are alive from Seagate. *Update the bad news is that I realize one of my 500GB's is about to die, it's not even a year old, but is also not affected by the recall according to Seagate! Seagate Inventory/Firm........
  • Convert HDD/Hard Drive Partition(s) into non-RAID into RAID 1 using existing data without data loss and without reformatting.


    Before we start I take no responsibility for this, you should have a backup and if you make a mistake during this process you could wipe out all of your data. So backup somewhere else before starting this as a precaution, or make sure it's data you could afford to lose. The RAID 1 Setup (Hardware Wise) I've already setup my 2 x 1TB (Seagate) drives with identical partitions, make sure your new hard drive (the empty one) is setup like your curr........
  • Linux EXT3 16GB-17GB maximum filesize issue solved/how to fix


    I have no idea why but mkfs.ext3 defaults to a patheticlly small blocksize of 1024 bytes/1KB (kilobyte). That means the maximum filesize is ONLY 16GB! With 2KB/2048 bytes you get a 256 GB maximum filesize, and with 4KB/4096 bytes you get 2TB! I finally noticed/paid attention to this after realizing that with rsync and scp that no file larger than 17GB could be transferred. I then realized it must be a file size limit on the partition. Here is what tune2fs tol........
  • OpenVZ backup container to a single file while it's running using "vzdump"


    Proxmox has made this free utility to backup running OpenVZ containers. It's a great program which is actually just a PERL script but gets the job done. This program is not 100% required because all it really does is cp -a from your container's path as far as I know but it is still good to have uniformity to how you backup your containers. For RPM distros such as Centos/RHEL/Fedora etc.. download and install this: wget http://www.proxmox.com/cms_proxm........
  • ntfs-3g Error/Fix/Solution - Unexpected sectors per cluster value (127). Failed to mount '/dev/sda1': Invalid argument The device '/dev/sda1' doesn't seem to have a valid NTFS. Maybe the wrong device is used? Or the whole disk instead of a


    ./ntfs-3g /dev/sda1 /mnt -o force Unexpected sectors per cluster value (127). Failed to mount '/dev/sda1': Invalid argument The device '/dev/sda1' doesn't seem to have a valid NTFS. Maybe the wrong device is used? Or the whole disk instead of a partition (e.g. /dev/sda, not /dev/sda1)? Or the other way around? This is happening on a system I've come across an HP 6930P running Windows XP Professional. The partition appears to be very norm........
  • Compaq V2405CA Laptop - Unixbench Performance Test


    Here are the results, it is Sempron 3000+ AMD Mobile, 500Gig HDD, 512MB RAM with shared ATI Radeon graphics. # # # # # # # ##### ###### # # #### # # # # ## # # # #&nb........
  • heartbeat is stopped for some reason


    heartbeat is stopped for some reason Anyway hnode2 was active and the services are running fine but I see heartbeat has been stopped somehow. Here is the last log I see of heartbeat: [quote:23c84415f5] Sep 9 17:15:32 hnode2 heartbeat: [16738]: info: MSG stats: 9/1762471 ms age 0 [pid16738/MST_CONTROL] Sep 9 17:15:32 hnode2 heartbeat: [16738]: info: cl_malloc stats: 716/51784021 152624/74519 [pid16738/MST_CONTROL] Sep 9 17:15:32........
  • View Disk Space Usage sorted by the size


    View Disk Space Usage sorted by the sizeUse: [code:1:8f675c5910]du -h | sort -n[/code:1:8f675c5910] The -h in du makes it show Kbytes or Mbytes instead of just bytes making it easier to read. The sort -n will show the files in order of smallest to largest *Note if you specify sort -nr instead then it will show the largest files first.........
  • How to Track Down/Find Cause of Linux high disk iowait/wa


    top - 09:34:12 up 2 days, 20:57, 2 users, load average: 1.83, 1.99, 2.03 Tasks: 59 total, 2 running, 57 sleeping, 0 stopped, 0 zombie Cpu(s): 0.3%us, 0.0%sy, 0.0%ni, 0.0%id, 99.7%wa, 0.0%hi, 0.0%si, 0.0%st That 99.7% wa is iowait, it means the server is waiting for a process to complete an IOoperation or in plain English, there is a delay in........
  • Using a Mac OSX DMG Image in Windows and Converting to Standard ISO Format use dmg2iso


    The dmg format is silly and annoying to work with, why couldn't Apple stick with the .iso standard? Anyway, there's an excellent Linux and Windows based tool to convert it back to a normal .iso Image called dmg2iso I'll only cover theLinux version although the Windows pre-built binary works the same way. Download dmg2iso here for free (from the author's website) It's just silly and doesn't make sense that Ubuntu doe........
  • Latest Articles

  • Ubuntu Debian Mint Linux SSHD OpenSSH Server Not Starting After Reboot Solution
  • nmap how to scan for all ports and not just the 1000 most common ports
  • Windows 7,8,10 and Server 2008, 2012, 2016, 2019 Read Only Attribute Won't Go Away
  • bind / named how to make a wildcard record and retain defined A records
  • Cisco Unified Communications Manager 12 Install Errors on Proxmox/KVM
  • Local Vs Universally Administered MAC Address NIC Refuses to come up
  • Cisco Unified Communications Manager 12 CUCM 12 - How To Enable Video Calling
  • Windows 7, 8, 10, Windows Server 2008, 2012, 2016, 2019 How To AC97 Audio Drivers and Other Unsigned Drivers
  • Cisco Unified Communications Manager / CUCM IP Telephony Definitions
  • tftp Linux xinetd verbose logging
  • Linux delete unused tap devices automatically
  • Linux qemu-kvm How To Enable Soundcard in Guestl
  • QEMU-KVM Windows and Server Guest Installs Mouse Tracking Pointer Location Solution
  • SSH Keep Alive To stop Disconnections
  • Linux How To Disable SATA NCQ For Better Performance
  • the sign-in method you're trying to use isn't allowed. For more info, contact your network administrator - solution for active directory
  • gsmartcontrol for Windows to Check the SMART S.M.A.R.T status
  • WebRTC Vulnerability Shows Local IP Address Even When Using a Proxy or VPN Firefox Fix And Disable Solution
  • chroot in Linux Howto Simple and Easy Guide
  • qemu-kvm qemu-system Image format was not specified for '/mnt/space/cucm12.img' and probing guessed raw. Automatically detecting the format is dangerous for raw images, write operations on block 0 will be restricted. Specify the 'ra