• Cisco Unified Communications Manager 12 Install Errors on Proxmox/KVM


    The strange thing is that usually the first install or two will work on any new machine but then it suddenly won't. I had this experience on QEMU 2.13 on a different machine. There is something finicky or buggy about the CUCM installer even when choosing the same virtual hardware specs. qemu-kvm command: /usr/libexec/qemu-kvm -version QEMU PC emulator version 0.12.1 (qemu-kvm-0.12.1.2-2.506.el6_10.1), Copyright (c) 2003-2008 Fabrice Bellard ........
  • Cisco Router Setup Guide and Tutorial Howto With Commands and Examples


    In most of the Cisco router IOS I find the ports like ge0/0 ge0/1 and ge0/2 or whatever your ports are down. They will not even give you a link light. So one of the first tasks should be getting the port you are working with up. In my case the first goal is often connectivity with the LAN and WAN. LAN = your local area network (eg. in the office/home ) WAN= your ISP/public internet (eg. fiber/cable/dsl/ethernet). In these examples I as........
  • Cisco 2960 Switch Reset To Factory Defaults


    *The easy way is to just hold the mode button for 10+ seconds. The full/proper way is below: 1.) Either power on the unit and hold the "mode" button or hold the "mode" button until you see the below: 00:04:08: %SYS-7-NV_BLOCK_INIT: Initalized the geometry of nvram 00:04:08: %EXPRESS_SETUP-6-CONFIG_IS_RESET: The configuration is reset and the system will now reboot 00:04:09: %SYS-5-REL........
  • LUKS Hard Drive Encryption on Linux Mint Ubuntu Debian etc how to mount encrypted hard drive


    The key thing here is to know the actual partition that is encrypted. Often in Linux Mint's installer that ends up being partition 5 or /dev/sda5 sudo cryptsetup luksOpen /dev/sda5 anynamehere You will then be prompted for your irrecoverable passphrase: Enter passphrase for /dev/sda5: If all goes well it won't say anything further. If it says ""No key available with this passphr........
  • Debian 9 SSH root password authentication failure password not working problem / solution


    In Debian a lot of times SSH disables the root user to login by password by default. This means you will get an authentication failure as if you typed in the wrong password. The logs also indicate the password is wrong but what is often the case is in the config file Check /etc/ssh/sshd_config cat /etc/ssh/sshd_config|grep -i permitrootlogin Make sure it says: PermitRootLogin yes If not change it and restart SSH........
  • systemd management using systemctl and journalctl to check systemd logs


    systemd is like the service manager for your Centos and other modern Linux distributions (including Debian/Mint/Ubuntu) allows you to enable services, stop them, restart them, check their status and even reboot your system. The key commands or arguments you will use with systemctl are the following: Unit Commands: list-units [PATTERN...] List loaded units &nbs........
  • gvfs mount in /run/user cannot be accessed or displayed wrong permissions


    The folder contents could not be displayed Backend currently unmounting drwx------ 10 userhere group 260 Aug 23 19:40 .. ?????????? ? ? ? ? ? sftp:host=192.168.8.80,user=adhoc ls: cannot access 'sftp:host=192.168.8.80,user=adoc': Input/output error $ ps aux|grep fuse one 253........
  • zenity popup messages, windows, dialogs, error messages calendars and more howto on Gnome Linux including Ubuntu, Linux Mint, Centos and more


    zenity is a nice utility as part of the gnome window manager that allows you to script from bash and retrieve the input from the user. It could also be helpful in just notifying a user when they login with a popup window. I'll give an overview of what's available with zenity: Application Options: --calendar Display calendar dialog --entry Display tex........
  • VMWare Vsphere VCSA Graphical Install Creates json


    yes it does create its own json ============================================ cat /tmp/vcsaUiInstaller/ovftool-20180809-175238948-20180809-175603497.log |grep -i json 2018-08-09T17:56:04.238-07:00 verbose OVFTool[30966] [Originator@6876 sub=Default] Manifest file entry: SHA1(VMware-vCenter-Server-Appliance-6.7.0.12000-8832884_OVF10-file1.json) = 1deb658c724767697587d5909c4051c01813e6a1 --> ........
  • ./xmr-stak: error while loading shared libraries: libmicrohttpd.so.10: cannot open shared object file: No such file or directory


    The solution is just to install libmicrohttpd-dev ./xmr-stak ./xmr-stak: error while loading shared libraries: libmicrohttpd.so.10: cannot open shared object file: No such file or directory libmicrohttpd libmicrohttpd10 - library embedding HTTP server functionality libmicrohttpd-dbg - library embedding HTTP server functionality (debug) libmicrohttpd-dev - library embedding HTTP server functionality (development) $ sudo apt-get i........
  • Debian Mint Ubuntu compiling xmr-stak


    sudo apt-get install libcurl4-openssl-dev git build-essential autotools-dev autoconf libcurl3 sudo apt-get install libcurl4-gnutls-dev git clone https://github.com/wolf9466/cpuminer-multi sudo apt-get install cmake libpthread-* libmicrohttpd-dev libssl-dev libhwloc-dev git clone https://github.com/fireice-uk/xmr-stak-cpu.git make install cd bin chmod +x xmr-stak-cpu ./xmr-stak -O xmr........
  • VMWare 6.7 VCSA VSphere ESXi Management SSO Install Guide on Linux using the CLI


    #mount the VCSA DVD mount /dev/sr0 /mnt/cd #alternatively you could mount the iso directly mount -o loop vcsa.iso /your/mount/path #for this purpose we are using the CLI installer on Linux cd /mnt/cd/vcsa-cli-installer/lin64 #no it's not going to be that easy you can't just run vcsa-deploy like that you need to use a template or configured .json file ./vcsa-deploy Usage: vcsa-deploy [-h] [--version] [--supported-deploymen........
  • OpenVPN auth-user-pass-verify ENV script error


    Starting with newer versions of OpenVPN Ibelieve 2.2+ you need to have "script-security 3" set or you can't execute a third party script. Prior to that you could also use the auth-user-pass-verify like this: auth-user-pass-verify ./validate.pl "$username $password $ip" via-env Options error: the --auth-user-pass-verify directive should have at most 2 parameters. To pass a list of arguments as one of the paramete........
  • postfix errors fatal: no SASL authentication mechanisms /usr/libexec/postfix/smtpd: bad command startup -- throttling solution


    Jul 3 22:12:17mailserver postfix/smtpd[6195]: fatal: no SASL authentication mechanisms Jul 3 22:12:18mailserver postfix/master[4881]: warning: process /usr/libexec/postfix/smtpd pid 6195 exit status 1 Jul 3 22:12:18mailserver postfix/master[4881]: warning: /usr/libexec/postfix/smtpd: bad command startup -- throttling This only ever happens in my experience when the authentication method is actually Dovecot. Usually the problem........
  • Maximum number of connections from user+IP exceeded (mail_max_userip_connections=10) Dovecot Solution


    This happens because Dovecot limits the maximum IMAPconnections per IPto just 10. This may be fine for a single client side IPbut if an entire office or multiple users are behind one IPor a single heavy user is active then you will get bizarre errors in your e-mail clients such as "Password Incorrect" or similar in Thunderbird. It won't be obvious on the client side as to what the problem is and they will probably just think the server is misconfi........
  • Prevent SSH Bruteforce and Hacks By Disabling Password Authentication


    One simple way to keep your server public but almost impossible to hack via SSHis to disable password authentication over SSH. This means the only way in is via your own private key that only you should have. Edit your /etc/ssh/sshd.conf file Set this option PasswordAuthentication no Restart your SSH server. service sshd restart ........
  • error: Could not locate RPC credentials. No authentication cookie could be found, and no rpcpassword is set in the configuration file Bitcoin Litecoin Error


    error: Could not locate RPC credentials. No authentication cookie could be found, and no rpcpassword is set in the configuration file This is usually because the .cookie file cannot be read by the user you are running Litecoin or Bitcoin client/daemon as. You can adjust the permissions of the file so that the user or group they are apart of has read permissions. ........
  • Centos 7 Root Password Reset


    In Centos 7 the days of editing the "kernel"line and adding "single"are gone. On top of that sometimes after a new install passwords do not work, maybe you forgot your password or for some other reason you need to break in or fix your system? It could also be because you can't mount your root / or some other /etc/fstab error and many other errors. Short Version: 1. Edit your grub settings and find the linux16 /vmlinu........
  • mysql how to reset passwords with a few commands


    The commands below will help you reset any mysql user password. use mysql; update user set password=PASSWORD('thenewpass') where User='theusername'; flush privileges; The first line says to use the "mysql" database which contains all the user info. the second update line sets the new password "thenewpass" for the u........
  • How To Create Apache htpasswd file


    This just simply outputs what you need a username and password that can be used to authenticate from .htaccess htpasswd -nb user password user:Gnb6uE9Lp4gt2 If you want to write it straight to a file htpasswd -cb /tmp/somefile.pw user password How To Use This In .htaccess AuthUserFile /tmp/somefile.pw AuthName GetLost!! AuthType B........
  • mysqld in Linux hacked


    Check for crap in /var/lib/mysql like this ls -al /var/lib/mysql/ total 20888 drwxr-xr-x 24 mysql mysql 4096 Oct 3 18:30 . drwxr-xr-x 20 root root 4096 Oct 3 04:23 .. -rw-rw-rw- 1 mysql mysql 11776 Oct 3 17:10 c:exp.exe -rw-rw-rw- 1 mysql mysql 48128 Oct 3 17:10 c:exp1.exe........
  • Disable SSH Password Authentication to Increase Security and Harden SSH Linux Unix Server Ubuntu Mint Centos Debian


    Just a note before you do this you should have a sure, guaranteed way into the system such as local, KVMor preferably publickey making bruteforce SSH absolutely impossible since there is no password to bruteforce and even if someone knew the password they wouldn't be able to login except from the local console (presumably you should make sure no one unauthorized has physical access). 1. Edit /etc/ssh/sshd_config Find the section like this:........
  • ecryptfs how to mount or recover from a backup


    The easiest way to recover or mount an off-line ecryptfs directory is the built-in command from ecryptfs sudo ecryptfs-recover-private It will find your wrapped passphrase and ask for your password and mount it in tmp. Much easier especially when your current active OS is using ecryptfs too. This a fantastic tool when going through old backups.........
  • Wine uninstalled broken on Linux Mint


    Solution: Aptitude is very smart and fixed the issues it was because of nvidia cuda and opencl and nothing else suggested or hinted this using apt sudo aptitude install wine The following NEW packages will be installed: ocl-icd-libopencl1{ab} ocl-icd-libopencl1:i386{ab} wine wine1.6 wine1.6-amd64{a} wine1.6-i386:i386{a} The following packages will be REMOVED:........
  • How to change reserved blocks in Linux partition


    user@box:~$ sudo tune2fs -l /dev/md99 [sudo] password for user: tune2fs 1.42.9 (4-Feb-2014) Filesystem volume name: Last mounted on: /mnt/md50 Filesystem UUID: 976a8655-2619-4587-878c-dab07f7b7652 Filesystem magic number: 0xEF53 Filesystem revision #: 1 (dynamic) Fi........
  • rsync run as root sudo without password


    This is a common issue, what if a issue shouldn't have root but you want to use that user to make a full backup of a system? They of course need root access. You can actually just give them passwordless sudo access to rsync in /etc/sudoers: sudo vi /etc/sudoers yourusername ALL = NOPASSWD: /usr/bin/rsync Here is how you would execute rsync: The key thing for the remote host is to........
  • cPanel error Access denied for user 'root'@'localhost' when adding remote MySQL IP address solution


    Error while connecting to MYSQL: (XID 4ea7s9) Access denied for user 'root'@'localhost' (using password: YES) at /usr/local/cpanel/Cpanel/Mysql.pm line 181 Solution This error occurs because the /root/.my.cnf has the wrong/outdated password for MySQL root user. Simply edit /root/.my.cnf with the correct user. This normally happens if you update outside of cPanel.........
  • Linux bash script how to generate a random password using /dev/urandom


    This command will generate a random password using all letters and numbers that is 20 characters wrong based on /dev/urandom (for the most truly random output). echo `< /dev/urandom tr -dc _A-Z-a-z-0-9 | head -c${1:-20};echo;`........
  • How to create openssl md5 password hash to use in /etc/shadow using bash


    Very useful in embedded and other non-standard deployments. The above makes a random salt of 14 random characters from /dev/urandom (you can change the -14 to whatever number of characters you want for your salt). openssl passwd -1 -salt `< /dev/urandom tr -dc _A-Z-a-z-0-9 | head -c${1:-14};echo;` YourPassword Output: $1$eW-ScuyL$f/iKMJ5mbJ..7bSzvX6EO0 ........
  • ENOM TRANSFER passwords do not match - solution


    The "passwords do not match" implies or makes it appear that your auth code is wrong but actually you have to click "View additional settings" and then see there are 2 password fields to manage the domain once it is transferred (the password is typed twice for confirmation). Simply fill out a password twice or remove the first password fields contents and all will be well.........
  • ERROR 2013 (HY000): Lost connection to MySQL server during query


    The solution is simple but strange, if you copy your /var/lib/mysql directory to another server and think it will work, be sure to check if you have /var/log/mysql and binary log files. If you do, the server will not work and will give you errors like below and crash without the proper log files. UPDATE user SET password=password("newpass") WHERE user='root'; flush privileges; ERROR 2013 (HY000): Lost connection to MySQL server durin........
  • openvpn 2.3.10-1.el6 issues auth-env does not work correctly for auth-user-pass-verify


    openvpn 2.3.10-1.el6 issues in the .conf auth-user-pass-verify "passwordcheck $username $password $untrusted_ip" via-env auth-env does not work correctly in OpenVPN 2.3: Sat Apr 23 02:30:22 2016 - $username - $untrusted_ip - login failure But OpenVPN 2.2 does work as expected. It could be that the specified script automatically receive........
  • Linksys E2500 DD-WRT Upgrade Instructions and Enabling 5ghz with Tomato Firmware


    1.) Flash directly to this file: http://tomato.groov.pl/download/K26RT-N/build5x-132-EN/Linksys%20E-series/tomato-E2500-NVRAM60K-1.28.RT-N5x-MIPSR2-132-Max.zip *I was never able to get the larger "Mega" file to work, at least not initially so I recommend the file above. To enable 5ghz I had to do the "Clear NVRAM" Option before it was shown. 2.) Or if you don't need 5ghz (most devices do not support it and cannot........
  • Linux Mint/Ubuntu/Debian Dual NICs networks problem when enabling and disabling one device


    The Scenario You have dual NICs and you disable NIC1 which uses 192.168.1.1 as its gateway. With NIC2 you enable it/connect it to another network which also has the gateway 192.168.1.1 Everything will work fine at this point. When switching back to NIC1 even with NIC2 disabled and even unplugged, the OS basically can't pick up the new/updated ARP entry of the old device for 192.168.1.1 and perhaps thinks it is a security risk or spoof of some sorts and blocks i........
  • Virtualbox errors on Ubuntu/Debian/Mint


    The solution was to reinstall the vbox dkms package and do a manual modprobe of the modules it makes. I never sorted out the unable to start due to the USB issue, I did have the guest additions installed but the only way to boot was to change the pointing device from USB to PS2 and then to disable the USB controller (if your pointing device is set as USB, disabling USB will not work because it will re-enable by default when it sees your pointing device is USB, this is w........
  • Linux sudo config sudoers to run command without a password howto


    Before reading on remember to put the line at the bottom of /etc/sudoers as from experience what happen is that other rules cancel out what you have added. If your sudoers setup is correct it will work immediately upon saving without requiring a reboot. Edit /etc/sudoers yourusername ALL = NOPASSWD: /path/to/command *Once again remember the above should be on the bottom of the sudoers file or........
  • ONVIF Linux Security Camera Setup


    First of all this seems to apply to many ONVIF devices Hard coded IP: 192.168.1.10 (yes not kidding no DHCP!) 00:12:12:9C:C2:00 To view RTSP stream use VLC, or openRTSP or other RTSP capable software: rtsp://192.168.1.10/user=admin_password=tlJwpbo6_channel=1_stream=0.sdp user: admin password: blank http://ip/Login.htm Uses Quicktime and is a poor quality picture and slow Cannot change pass........
  • Installing zoneminder on Ubuntu/Debian Linux Howto


    sudo apt-get install zoneminder [sudo] password for one: Reading package lists... Done Building dependency tree Reading state information... Done The following packages were automatically installed and are no longer required: libuser-perl python-evince kdebase-apps kwrite unixodbc libgnomeprint2.2-data python-soappy vgabios python-metacity hddtemp python-mediaprof........
  • HP Procurve Switch 2824 CLI Telnet Experience , Guide and Tutorial


    telnet 192.168.1.54 ------------------------------------- ProCurve J4903A Switch 2824 Software revision I.10.77 Copyright (C) 1991-2009 Hewlett-Packard Co. All Rights Reserved. RESTRICTED RIGHTS LEGEND Use, duplication, or disclosure by the Government is subject........
  • Disable cphulk in CPanel if you can't login even with the right password


    It's a great feature to ward off bruteforce but is also annoying because you think you have the wrong password when you can't login. How to Disable cp hulk for 5 minutes /usr/local/cpanel/etc/init/stopcphulkd........
  • Vbox/Virtualbox devices grayed out for non-root user solution


    It is a permissions issue that is hard to fix. All but one USB device is greyed out. I am already a member of "vboxusers" I have already enabled and disabled USB support for the guest. I have already reinstalled the latest VBOx guest editions If running as root it all works fine Changing........
  • Samsung Printer Password Login to change settings CLP


    First of all to find your IP you can hold the "X" button for a few seconds and it will print out the DHCP IP. Another way to find the IP that I prefer is to login to your router or switch and find a hostname that says something like "SEC001599CD2948" which will be your Samsung printer (at least for the C3xx or C4xx series of Samsung printers). The login and password for Samsung Syncthru Webservice:........
  • CPanel Link to all of the command line options


    CPanel says you can access 98% of the functions through CLI which experienced Unix/Linux admins prefer for simplicity and for scripting.  I've never found CPanel easy to use from the admin panel, it seems everything is hard to find and a simple task becomes a series of hunts. So for people like me here's the list: http://cpanel.net/system-administrators/command-line-scrip........
  • phpBB create new email hash manually when modifying or adding user manually directly through MySQL


    Many may ask why would you need to do this? When upgrading from phpBB 2 to 3 the conversion does not keep the admin user you create. If your old admin user has an email address associated that no longer works or is accessible this makes it impossible to reset the admin password. Some may just say "I'll just manually edit the e-mail address" but it won't work and phpBB will fail to find that user if you don't update the "user_email_hash" field but how do........
  • CPanel mysql root password location how to find


    It is located in /root/.my.cnf This is truly a horrible idea and a security flaw and on top of that MySQL port 3306 is wide open by default with CPanel.........
  • Wordpress Security Hole, Plug it by manually installing themes and plugins


    It's always bothered me how Wordpress basically forces the user to provide their hosting credentials to install themes and plugins. How do know for sure the data is not being saved, intercepted and being provided backdoor access to the NSA or other agencies or even just being misused by others with access? Here's how to close the security hole above and if you're already given Wordpress your credentials make sure you change everything associated it with it. Eg. change your........
  • cPanel VPS Server Cannot Login as root


    I was worried the server was hacked, I was logged in already as root but couldn't login to CPanel or a new SSHsession. I even reset the password from the shell and it did not work still. The reason is CPanel Hulk, it detected a brute-force attack so it locked down the root account entirely even from the correct password. According to cPanel the best way around this is to whitelist your IP.........
  • Linux Ubuntu Debian Howto Manually Update/Install Thunderbird


    wget http://download-location sudo tar xjvf thunderbird-24.2.0.tar.bz2 -C /opt ln -s /opt/thunderbird/thunderbird /usr/bin/thunderbird [sudo] password for one: ln: creating symbolic link `/usr/bin/thunderbird': File exists sudo rm /usr/bin/thunderbird ln -s /opt/thunderbird/thunderbird /usr/bin/thunderbird The above is how Idid it, if you don't do it properly you'll find that you are still using the old version (........
  • Asterisk iptables block bruteforce attacks howto with fail2ban


    yum -y install fail2ban vi /etc/fail2ban/jail.conf [asterisk-tcp] enabled = true filter = asterisk action = iptables-multiport[name=asterisk-tcp, port="5060,5061", protocol=tcp] sendmail-whois[name=Asterisk, dest=you@example.com, sender=fail2ban@example.com] logpath = /var/log/asterisk/messages maxret........
  • Linux create htaccess file with username and password


    htpasswd -b -c filename username "password" -b = take the password that we specify in the command (don't prompt for it) -c = create the filename username=username password=password (I use quotes because it breaks if you use special characters)........
  • MySQL Allows blank user with no password to login


    I just realized I have some blank users which I deleted butI can still login to this dummy account without a password for some reason. mysql -u -p Welcome to the MySQL monitor. Commands end with ; or g. Your MySQL connection id is 5 Server version: 5.1.69 Source distribution Copyright (c) 2000, 2013, Oracle and/or its affiliates. All rights reserved. Oracle is a registered trademark of Oracle Corporation an........
  • WD 20EARX Dead Again


    Another new drive bad from the start: Jun 2 15:14:18 one-desktop kernel: [15895.386779] ata2.00: exception Emask 0x50 SAct 0x1 SErr 0x280900 action 0x6 frozen Jun 2 15:14:18 one-desktop kernel: [15895.386782] ata2.00: irq_stat 0x08000000, interface fatal error Jun 2 15:14:18 one-desktop kernel: [15895.386784] ata2: SError: { UnrecovData HostInt 10B8B BadCRC } Jun 2 15:14:18 one-desktop kernel: [15895.386788] ata2.00: cmd 60/0........
  • mysql how to execute script from the bash prompt .sql


    mysql -u username --password='yourpassword' ........
  • SSH Can't Login/Hang


    Client Log OpenSSH_4.3p2, OpenSSL 0.9.8e-fips-rhel5 01 Jul 2008 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug1: Connecting to 192.168.1.253 [192.168.1.253] port 22. debug1: Connection established. debug1: permanently_set_uid: 0/0 debug1: identity file /root/.ssh/identity type -1 debug1: identity file /root/.ssh/id_rsa type 1 debug1: identity file /root/.ssh/id_d........
  • Login and download all files script


    This is very handy if you're too busy and don't have time to download whatever files you need. The -D specifies the domains allowed, this is because I specified -H which means foreign hosts are allowed, if you don't restrict them you'll end up going to the whole internet via ads and other links just like a search Engine would follow. -l 0 specifies to go deep, to as many levels as possible/as exist. -e robots=off is important because robots.txt often says you can't vie........
  • MySQL Authentication fails after Upgrade to Version 5.5


    ERROR 1045 (28000): Access denied for user 'contentmanager'@'localhost' (using password: YES) For fun I thought I'd reset the password: GRANT ALL ON thecontent.* TO contentmanager IDENTIFIED by 'dfdfsdfdsfsdfsd'; ERROR 1470 (HY000): String 'contentmanager' is too long for user name (should be no longer than 16) This is ridiculous that this new version has some bizarre 16 character username limit and not only that but i........
  • HowTo Migrate and Import iPhone/Outlook Contacts into Android without using GMail using .vcf files


    I searched for days after getting my Galaxy Note and couldn't find a way to do this (at least not without buying programs for either Android/Windows). All I read was ways to sync and import the contacts to GMail but I don't want to use GMail for privacy reasons. GMail/Google steal all of your personal information and use it for whatever purposes they want to and may sell or release it to who knows where (I don't care what their policy says but this stuff happens), just like the default........
  • Drupal/MySQL database error: PDOException: SQLSTATE[42000] [1044] Access denied for user 'db_user'@'localhost' to database 'dbname' in lock_may_be_available() (line 167 of /home/user/public_html/includes/lock.inc).


    PDOException: SQLSTATE[42000] [1044] Access denied for user 'db_user'@'localhost' to database 'dbname' in lock_may_be_available() (line 167 of /home/user/public_html/includes/lock.inc). The username and password were correct but some reason CPanel added the user with no permissions! Edit the user's permissions to include "All" from Cpanel or MySQL and that is the solution.........
  • screen Cannot open your terminal '/dev/pts/2' - please check.


    The solution to this screen issue is simple. This happened to me in Centos 5 as a user, but I also su'd to it and I don't have any password for it. I've read some people say this is more common when su'ing. The solution is simple though, just give others rw access to the corresponding pts whether it's 0,1,2 etc..: As root do chmod o+rw /dev/pts/2 ........
  • pgina can't login after installing


    After Installing pgina I couldn't login to Windows anymore with my blank password Administrator account! An unknown error has prevented your account from being created.nrThis may be due to policy or security settings as well as other machine configuration.nrPlease consult your administrator. Hit F8 to start Windows in Safe Mode and you can login normally and then remove PGina, it shouldn't cause this problem or behavior out of the box.........
  • Plesk Get List of E-mail Users & Aliases


    When migrating away from Plesk I couldn't figure out an easy way to get a straight list of all e-mails, but here is where I found the solution: http://nakuls77.wordpress.com/2008/08/30/details-of-email-ftp-database-users-from-psa-database/ mysql> SELECT mail.mail_name, accounts.password, domains.name FROM mail, accounts, domains WHERE domains.id=mail.dom_id AND mail.account_id=accounts.id; mysql> SELECT CONCAT(mail.mail_name,’@’,domains.name) AS Em........
  • Installing Webmin & Enabling SSL


    Webmin Setup Centos 5: wget http://downloads.sourceforge.net/project/webadmin/webmin/1.530/webmin-1.530-1.noarch.rpm?r=http%3A%2F%2Fwww.webmin.com%2Fstandard.html&ts=1294339690&use_mirror=surfnet [1] 24229 [2] 24230 [root@host ~]# --2011-01-06 21:48:20-- http://downloads.sourceforge.net/project/webadmin/webmin/1.530/webmin-1.530-1.noarch.rpm?r=http%3A%2F%2Fwww.webmin.com%2Fstandard.html Resolving downloads.sourceforge.net... 216.34.181.........
  • rsync preserve attributes, permissions/ownership and times without being root non-root user


    One of the purposes of rsync is to backup whole filesystems and archive them but how can you do that properly and restore things to normal if all permissions and ownerships are not preserved from your root filesystem? It's not desirable to have everything running as root, especially not just for an rsync. The Easy rsync preserve permission solution for non-root users sudo is the answer and all you have to do is edit /etc/sudoers At the end o........
  • Error: DBus error org.freedesktop.DBus.Error.ServiceUnknown: The name :1.1127 was not provided by any .service files Please select another viewer and try again.


    This is an SFTP mount that does not work or prompt for password. Error: DBus error org.freedesktop.DBus.Error.ServiceUnknown: The name :1.1127 was not provided by any .service files Please select another viewer and try again. It seems to me that the connection often times out after being opened and the application doesn't know how to handle the disconnection and doesn't realize it needs to kill the instance and restart the connection.........
  • FUSE/Curlftpfs mount ftp account as drive partition in Linux


    This is a great way to use your ftp server space, for example on your web hosting account (althoughI believe many hosts don't allow storage like this), but if you have a VPS/Dedicated Server etc.., this would be perfect. Imagine how easy it is to work with an ftp account that you can just mount as a normal partition or directory in Linux, it would be great for backups etc.. Name curlftpfs - mount a ftp host as a local directory Synopsis........
  • LUKS/cryptsetup Tutorial for Linux Hard Drive Partition Encryption


    This is based on Debian Linux but should apply equally to any *nix distro. Install LUKS/crypt-setup apt-get install cryptsetup Setup your LUKS Partition Of course change /dev/md2 with whatever partition you intend to use LUKS on. cryptsetup --verbose --verify-passphrase luksFormat /dev/md2 You'll be asked to verify your decryption password twice *DO NOT FORGET THIS PASSWORD AS IT IS NOT RECOVERABLE!........
  • MySQL Recover/Reset Lost/Forgotten root Password


    One note is to secure MySQL, I don't know for sure but I believe you could login to MySQL remotely with no password during this operation (I'm not sure, maybe it doesn't accept blank passwords but I firewall MySQL port anyway and recommend you do the same). First edit /etc/my.cf Under the [mysqld] field add the following line somewhere: skip-grant-tables Now restart mysql: service mysql restart or on Debian sty........
  • SSH Automatic/Passwordless Logon - Setup Public Key Encryption In Single Command


    This is a very simple solution, but most guides out there make you login twice (once to scp the key) and once to put the key in authorized_keys. There's no need for that. If you don't already have a ~/.ssh/id_rsa.pub just type "ssh-keygen -t rsa" and keep hitting enter until it's done :) Just use this code to easily enable passwordless login with SSHD key=`cat ~/.ssh/id_rsa.pub`;ssh user@192.168.5.25 "echo $key >> ~/.ssh/auth........
  • Picking an FTPD (vsftpd) Server in Linux Centos/Debian


    I decided on using yum to help me decide even though I normaly use proftpd I decided to see what else I could find. yum search ftp Loaded plugins: fastestmirror Loading mirror speeds from cached hostfile * rpmforge: ftp-stud.fht-esslingen.de * base: mirrors.netdna.com * updates: updates.interworx.info * addons: yum.singlehop.com * extras: mirrors.netdna.com rpmforge........
  • SSH automatic login without password


    SSH automatic login without passwordlocal> ssh-keygen -t rsa -f .ssh/id_rsa -t is the encryption type -f tells where to store the public/private key pairs. In this case, the .ssh directory on home is being used A password will be asked; leave this part blank, just pressing Now, go the .ssh directory, and you will find two new files: id_dsa and id_dsa.pub. The last one is the public part. Now, copy the public key to the serv........
  • CREATE Database/Granting Privileges


    CREATE Database/Granting PrivilegesCREATE your first database Code: [code:1:0668cd8e74]CREATE database myfirstdb; [/code:1:0668cd8e74] CREATE a user for your first database This one creates the user 'sqladmin' and gives them 'usage' on your new database 'myfirstdb' Code: [code:1:0668cd8e74]mysql> GRANT usage on myfirstdb.* to sqladmin@localhost; Query OK, 0 rows affected (0.00 sec)[/code:1:0668........
  • Updated to Version 3.8 and can't login


    Updated to Version 3.8 and can't loginSSHD accepts my password but then hangs at "Last login: Wed Sep 13 21:30:02 2006 from" This occurred during a yum update after upgrading my release, installing the new kernel and rebooting. I got kicked out of sshd after seeing the following during yum update: telnet 100 % done 85/476 tux 100 % done 86/476 ntsysv 100 % done 87/476 rpmdb-redhat 94 % done 88/476........
  • SSH Public Key Authentication (Login Without Passwords)


    SSH Public Key Authentication (Login Without Passwords)I've gone over this before but just a quick note! the "authorized_keys" file in ~/.ssh must be chmodded to "600" or public key authentication won't work. I guess it's kind of a security/failsafe feature that I've seen on all Linux and Unix OS's........
  • MySQL root password


    MySQL root passwordWhen I installed MySQL I didn't set a root password nor do I know what it is![/b]........
  • MySQL Server 3.23 won't start after switching from 4.1


    MySQL Server 3.23 won't start after switching from 4.1I was using a 4.1 alpha version of mysql-server and some how version 3.23 of the client and 4.1 of the client were also both installed! So I forced uninstalled everything because after trying and trying even though MySQL server was using the short 16byte password authentication I got some other errors. After trying with the ports and having it fail because I had existing database data I force installe........
  • Use Mozilla Firefox, not Internet Explorer - You'll be glad!


    Use Mozilla Firefox, not Internet Explorer - You'll be glad!Hey guys, I just thought I'd recommend that everyone switch to Mozilla Firefox as their web browser. You can find it at http://mozilla.org It is free and it is much better than IE. It has a built-in popup blocker which works great and most importantly, it doesn't have a million critical security flaws which could compromise your security such as passwords for on-line banking etc..........
  • Create/Enable SSL Certificates for Apache on Linux/Unix Systems eg. Redhat,Centos,Debian


    Shortcut/Easiest Way To Create A Self-Signed Key: openssl req -new -x509 -nodes -days 1530 -out server.crt -keyout server.key Using the above, you instantly create a self-signed certificate valid for 1530 days and you can simply skip to step #5.) below. If You Need a Real SSLCertificate (eg. Equifax/Openssl) then you need to create a CSR request (you'll need to follow Steps 1.) and 2.) in order to create the CSR. You then upload the CSR Certi........
  • Adventures in pre-paid SIM Cards and data GPRS/Edge/3G in China with China Mobile in Shenzhen, Guangzhou, Shanghai, Beijing and other cities


    This really is a difficult and confusing process for non-Mandarin speakers, but here's what I've done and learned so far: You can purchase an "M-Zone" China Mobile pre-paid SIMCard from almost anywhere but I tried to purchase mine from Suning (a large electronics dealer) hoping they would be able to help me or answer my questions but my plan didn't work out at all. At Suning once I found someone who spoke some English they gave me the 55 RMB M-Zone China Mobile P........
  • Linux/Unix Open SSH Login Without Password Key Exchange including Debian, Redhat, Fedora, Ubuntu, BSD etc..


    In those 4 simple commands you can setup mutual key exchange between two sshservers by using a single login shell session and single window. *Just change the IP address examples of (10.10.0.2) to the target of your mutual key exchange. It doesn't matter if the server is on a LANor WAN(well unless the server is behind a firewall and you cannot SSHinto it).........
  • MySQL Restoring And Dumping/Backing UP MySQL Data/Tables/Databases


    Backing MySQL Databases Backing Up/Dumping All Mysql Databases To A Single File mysqldump --all-databases -u admin -p > allmysqldatabases.sql The "-all-databases" clause is pretty obvious isn't it? It means that it will backup all databases. The "-u admin" means login using the user "admin", if you h........
  • iPhone 3GS 32GB "Harsh Review"


    Yes, Iadmit I finally got bitten by the hype as much as I can usually see through it all. Keep in mind this review is of the "stock" phone, no jailbreaking yet which is what really unleashes the customizability and whyI bought iPhone. I had better things to say about this phone before buying it, and it is a great phone, perhaps the best on the market by far, if not because of the Mac OS port onto the iPhone and all the apps, etc, etc. With that said........
  • iPhone has no password/wand manager saving feature in Safari Web Browser


    I kind of expected this feature to be there in some form, to stay ahead of the pack Apple needs to stay on top of this. User's of HTC's Android smart phone which uses a Linux based OS with Google's power behind it, note that you can save passwords in the browser on that phone. Apple needs to continuously evaluate the needs in its core apps and make sure the features are cutting edge and top notch, if other phones come out with some of these seemingly small but essential features........
  • SSH Slow Login even with SSHD UseDNS no parameter


    Icouldn't understand why on one system it took a few minutes to get the SSHlogin prompt when connecting to other systems. The other systems all had the UseDNS parameter set to no, which almost always resolves the login prompt delay. The reason is Ubuntu and perhaps Debian and other distributions /etc/nsswitch.conf file Edit yours to have the "hosts" line like so (notice that files and dns are the primary resolution choice........
  • Samba SMB Error - Server not using user level security and no password supplied. tree connect failed: NT_STATUS_WRONG_PASSWORD


    Server not using user level security and no password supplied. tree connect failed: NT_STATUS_WRONG_PASSWORD That happens when trying to use smbclient to connect to a share. The weird thing is that I can authnenticate just fine from Windows XP. It is partially my mistake, I forgot this share does have a password. I've tried authenticating with the correct user and also with "Guest" because this works in Windows. In Linux I ........
  • Viewing and Connecting to an SMB Samba Share on Windows/Linux/Unix


    This will give you the basic info needed to browse and connect to Samba shares from the command line. From the GUI of Gnome or KDE etc, it is pretty standard and straight forward. However, I've found very little guides on how to do it from the command line and if you're like me, a nerd who prefers command line for its simplicity and for remote use, this is the way to go. First get a list of all the Samba/SMB shares on the target. smbclient -L hostname........
  • Latest Articles

  • ImageMagick Convert PDF Not Authorized
  • ImageMagick Converted PDF to JPEG some files have a black background solution
  • Linux Mint Mate Customize the Lock screen messages and hide username and real name
  • Ubuntu/Gnome/Mint/Centos How To Take a partial screenshot
  • ssh how to verify your host key / avoid MIM attacks
  • Cisco IP Phone CP-8845 8800/8900 Series How To Reset To Factory Settings Instructions
  • ls how to list ONLY directories
  • How to encrypt your SSH private key file id_rsa
  • Linux Mint 18 Disable User Name List from showing on Login Screen
  • Firefox Cannot Hit Enter Key In Address Bar and Location History Not Working
  • Cisco Unified Communications Manager / CUCM IP 8.6,10,12 Install Error Solution
  • Ubuntu Debian Mint Linux SSHD OpenSSH Server Not Starting After Reboot Solution
  • nmap how to scan for all ports and not just the 1000 most common ports
  • Windows 7,8,10 and Server 2008, 2012, 2016, 2019 Read Only Attribute Won't Go Away
  • bind / named how to make a wildcard record and retain defined A records
  • Cisco Unified Communications Manager 12 Install Errors on Proxmox/KVM
  • Local Vs Universally Administered MAC Address NIC Refuses to come up
  • Cisco Unified Communications Manager 12 CUCM 12 - How To Enable Video Calling
  • Windows 7, 8, 10, Windows Server 2008, 2012, 2016, 2019 How To AC97 Audio Drivers and Other Unsigned Drivers
  • Cisco Unified Communications Manager / CUCM IP Telephony Definitions