ClamAV update process started at Sun Mar 20 00:30:50 2022
WARNING: Your ClamAV installation is OUTDATED!
WARNING: Local version: 0.100.3 Recommended version: 0.103.5
DON'T PANIC! Read https://www.clamav.net/documents/upgrading-clamav
main.cld is up to date (version: 62, sigs: 6647427, f-level: 90, builder: sigmgr)
WARNING: getpatch: Can't download daily-26337.cdiff from db.local.clamav.net
These types of errors are normally caused by misconfiguration of your /etc/apt/sources.list.
In this example on Debian 10, if you didn't complete the install correctly, you will have no repos enabled and only rely on CDROM.
"Package wget is not available, but is referred to by another package. This may mean that the package is missing, has been obsoleted, or is only available from another source.
E: Package 'wget' ha........
Usually if you get the grub boot loader and it doesn't show any boot options, it's because grub was not installed correctly and/or the partition that it is supposed to be on has changed or does not exist. It can also happen if you install Linux to one drive, but the boot loader to another by accident, whether EFI or MBR/Legacy mode.
You can normally fix it by chrooting into your root partition:
#make a direc........
Just a quick note and warning is that if you are testing to see if EFIPXE booting works on a VM, MAKE SURE it actually works. For example Iinitially tested using my Distro's QEMU 2.5+dfsg-5ubuntu10.46 and ovmf BIOS firmware (OVMF supports EFI). However, I found on old versions of QEMU (like 2.5), EFIbooting with GRUB NEVER works so it may appear that you have made a mistake when everything is fine when you boot a physi........
It took a lot of fiddling to make a Huion Kamvas 13 Pro work in Linux but it simple once you know what to do. Don't bother searching as it is unlkely there is a guide out there that will actually make your tablet work.
It mainly comes down to the fact that the hid_uclogic kernel module is buggy or doesn't support MANYof these wacom based/Huion tablets properly.
What was happening with me is that Ihad the Kamvas 13 Huion setup as a secondary screen/monitor.&nb........
Oct 18 11:06:46 server systemd: rc-local.service: Failed at step EXEC spawning /etc/rc.local: Exec format error
Oct 18 11:06:46 server systemd: rc-local.service: Control process exited, code=exited status=203
Oct 18 11:06:46 server systemd: Failed to start /etc/rc.local Compatibility.
Oct 18 11:06:46 server systemd: rc-local.service: Unit entered failed state.
Oct 18 11:06:46 server systemd: rc-local.service: Failed with result 'exit-code'.........
The only solution after trying many suggestions was to simply restart the "vz" service (definitely not preferable).
Even doing an ifdown and ifup for venet0 did not help.
Bringing up interface venet0:
Configuring interface venet0:
net.ipv4.conf.venet0.send_redirects = 0
RTNETLINK answers: Network is down
Some errors from log:
CPT ERR: d2dc60........
Usually the cause is inexplicable because some things just don't work correctly even when calling all commands by their full path.
Usually adding the following to your crontab file at the top will fix/solve the issue:
There was a problem importing one of the Python modules
required to run yum. The error leading to this problem was:
No module named yum
Please install a package which provides this module, or
verify that the module is installed correctly.
It's possible that the above module doesn't match the
current version of Python, which is:
2.7.9 (default, Apr 21 2016, 16:51:58)
[GCC 4.4.7 20120313........
openvpn 2.3.10-1.el6 issues
in the .conf
auth-user-pass-verify "passwordcheck $username $password $untrusted_ip" via-env
auth-env does not work correctly in OpenVPN 2.3:
Sat Apr 23 02:30:22 2016 - $username - $untrusted_ip - login failure
But OpenVPN 2.2 does work as expected.
It could be that the specified script automatically receive........
1, Enter the command prompt
Start -> cmd
2. Start diskpart
3. Find the drive that has the wrong size
4. Select the volume (in this example we use volume 2)
select volume 2
5. Extend the volume
*Note the "exten........
If you get that message it means you have inserted the adapter or device incorrectly. In my case the adapter needed to be at the rear end of the pins and it caused this message.
Do not ignore this message as it may appear to work but you will get errors and in reality your chip will not be erased or programmed even if it appears like it is working.........
I messed up the bootloader by accident on a standard Centos 6.3 install because I turned the /dev/vda1 boot partition into an mdadm raid 1. This was all done correctly aside from one point Ididn't realize was an issue metadata=00.90 is the only thing that will allow you to boot (otherwise grub won't work and you won't boot).
So the next step is rescue mode from a CD right? The problem you will find is that grub does not detect your hard drives, this is Ibelieve is be........
Iread this article and still don't understand the issue.
If I understand correctly the client negotiates after the first SSLconnection and then gets the correct hostname and thus correct certificate.
To their credit I know I'm not using SNIbecuase Iget this message in the Apache log :)
[warn] Init: You should not use name-based virtual hosts in conjunction with SSL!!
At first it was configured as a RAID 0, then I deleted the Virtual Disk Group.
I thought both drives would be shown and detected in Linux as sda and sdb but it actually shows nothing.
To make them work you have to hit Ctrl+R before the system boots (when prompted) and create a Virtual Disk Group. In my case I created each one as RAID 0 (with a single drive only) as I just wanted JBOD but there is no such option or default in these Dell Pe........
Kernel panic - not syncing: Attempted to kill init!
Pid: 1,comm: init Tained: G I------------- 2.6.32-358.el6.x86_64 #1
 ? panic+0xa0/0x16f
 ? do_exit+0x862/0x870
 ? fput+0x25/0x30
 ? do_group_exit+0x58/0xd0
 ? sys_exit_........
This is e-mail notification to warn you that your hostname is setup improperly on your system.
This is an annoying message and bug with Directadmin, my hostname is set correctly, why does it complain?
To get of this message just run this command:
I wanted to Import/Use a .vmdk hard disk image file from VMWare. Generally you can just "point" VirtualBox to it and use it and it will work but I found an exception.
One of my Centos 4.4 x64 images wouldn't boot. I had two copies, an older one and the newer one. The older one booted as normal (once I changed the VirtualBox driver to IDE from SATA). The newer one stopped at the "GRUB loading" message no matter what I tried.
As far as........
After an upgrade wine wouldn't open anything, not even the pre-installed notepad.
There are no wine logs and nothing is mentioned in any standard log file about why.
I finally decided to run wine from the shell and see what's going on:
wine client error:0: version mismatch 398/402.
Your wineserver binary was not upgraded correctly,
or you have an older one somewhere in your PATH.
Or maybe the wrong wineserver is still running?........
GRUB Boot FreeBSD[code:1:a7050277b7]title FreeBSD 6.0
Just insert the above code into GRUB's [b:a7050277b7]menu.lst[/b:a7050277b7] and make sure you set the root path correctly.
[quote:a7050277b7]Let's quickly explain what the root (hd0,2,a) means:
*hd0 stands for the primary master drive
*2 stands for partition 3
*a stands for the........