This is how we configure outside PSTNaccess or dialing through another SIPtrunk. Beware that this a simplistic example that neglects most security including SRTP First you'll need to be in config mode: Step - 1 Enter Voice Service VOIP security options There are more options but for now we'll just focus on security/allowing connections to and from our phones and the trunk. Router(config)#voice service voip ........

Make sure this makes sense for you but I've started to block a lot of commercial Cloud services and easily accessible providers as they are a very high source of abusive traffic. The cost savings for a lot of organizations are huge, as you now have less bandwidth usage and less resource usage from garbage/bot/malicious traffic. This mainly works for when you can be reasonably sure that your audience has no business visiting your service(s) from freely accessible commercial IP ........

This can break things easily in remove environments where it was normally easy to convert a normal eth0 to a bridge under br0, and that bridge would normally have the same MAC address by default, which is desirable for most situations. In Debian 11 this is different for some reason now. https://unix.stackexchange.com/questions/681013/bridge-gets-random-mac-........

You can do a static lease that is tied to the MAC address but what a lot of users prefer is that they come into the office or lab the next day and that their device gets assigned the same IP address (if possible). As we can see in the dhcpd logs that there is threshold that is defaulted as we'll show later. Whatever the threshold is set at, if the lease is younger than the threshold, it will keep the same lease. In other words, if the device goes to sleep or is powered off........

If you get this error, it is often because you have configured Apache with modules that weren't actually installed. Eg. you try to load the PHPmodule but didn't actually install the apache2 php module, so the server can't start. In general, this error can often be caused by issues with problematic modules and/or Apache being configured for modules that have not actually be installed (eg. libapache2-mod-php) is missing. The above results in this less than obv........

You'll notice that /etc/resolv.conf contains dire warners on most Linux Desktops. # This file is managed by man:systemd-resolved(8). Do not edit. # # This is a dynamic resolv.conf file for connecting local clients to the # internal DNS stub resolver of systemd-resolved. This file lists all # configured search domains. # # Run "resolvectl status" to see details about the uplink DNS servers # currently in use........

Virtualbox is a very powerful tool, but for some use cases it is less than optimal. Say you are in a work, lab or other environment where you are not alone on the physical network and there could be overlap of IPs, but you need all of your VMs to be contactable from your host, VMs need to communicate with each other, and VMs need internet. NAT Network will give you VM to VM communication and internet, however, it is buggy and unstable. It also doesn't allow host to VM co........

If you are converting a generic wifi IP camera to ethernet, it may not be that simple as many are default hard coded to a static IP of 192.168.1.168 and login info admin/admin. From there you can login to the camera and assign it to DHCP by going to http://192.168.1.168 For security these cameras +DVR should be on a separate untagged VLAN or if possible a physically isolated non-internet connected switch/network. The reference below is applicable to many of the r........

How To Fix This Cisco Switch/Router Error %Error opening tftp %Error opening tftp://10.0.2.2/network-confg (Permission denied) %Error opening tftp://10.0.2.2/cisconet.cfg (Permission denied) %Error opening tftp://10.0.2.2/router-confg (Permission denied) %Error opening tftp://10.0.2.2/ciscortr.cfg (Permission denied) %Error opening tftp://10.0.2.2/network-confg (Perm........

Bonding is an excellent way to get both increased redundancy and throughput. It is similar to the "Network Teaming" feature in Windows. There are a few different modes but we will use mode 6, I think it's the best of both worlds, as it is not just a failover, but it provides round robin, so you will get redundancy and load balancing. So if you have a 1G single port, you will have a combined throughput of 4G at this point. Just bear in mind that the true thr........

If you are using mint, delete the preference that stops snap from installing (as it is required for lxc) sudo rm /etc/apt/preferences.d/nosnap.pref 1. Install lxd: sudo apt install lxd Issues install lxd or errors? Click here Debian at this time does not have lxd so you'll need to use snap: sudo apt in........

This can be used on almost anything, since Gluster is a userspace tool, based on FUSE. This means that all Gluster appears as to any application is just a directory. Applications don't need specific support for Gluster, so long as you can tell the application to use a certain directory for storage. One application can be for redundant and scaled storage, including for within Docker and Kubernetes, LXC, Proxmox, OpenStack, etc or just your image/web/video files or even da........

The Linux Mint team has disabled it by setting an apt preference, you can edit or just remove the file: sudo apt install snapd Reading package lists... Done Building dependency tree Reading state information... Done Package snapd is not available, but is referred to by another package. This may mean that the package is missing, has been obsoleted, or is only available from another source........

Enable "cli" mode equivalent in JunOS cli Configure Mode configure So rather than going to the console on a Cisco switch and typing "enable" and then "conf t", the equivalent in JunOS is "cli" and "configure". How Do You Apply Changes You've Made? You can make all kinds of changes to the switch, but remember they are not........

One simple flag to configure will create a makefile that statically links all the shared objects and embeds them instead the binary execute. This means as long as you have the same architecture that things should run. Eg. if you have an old version of Debian with a different version of glibc, then this will solve that problem. ./configure LDFLAGS="-static" To test that it is really statically linked run ldd: ldd src/wget........

yum -y install gcc make gperf genisoimage flex bison ncurses ncurses-devel pcre-devel augeas-devel augeas readline-devel checking for cpio... cpio checking for gperf... no configure: error: gperf must be installed configure: error: Package requirements (augeas >= 1.2.0) were not met: Requested 'augeas >= 1.2.0' but version of augeas is 1.0.0 yum remove augeas augeas-libs augeas-devel wget http://downl........

apt install software-properties-common add-apt-repository ppa:deadsnakes/ppa apt update apt install python3-pip apt install python3.7 curl gnupg python3.7-dev git ln -s /usr/bin/python3.7 /usr/bin/python3 pip3 install numpy keras_preprocessing curl https://bazel.build/bazel-release.pub.gpg | sudo apt-key add - echo "deb [arch=amd64] http://storage.googleapis.com/bazel-apt stable jdk1.8" | sudo tee /etc/apt/sources.list.d/bazel........

Most newer distros inexplicably cause your NIC to have what Icall "random" non-standard name conventions because of systemd. This is a big problem for many people and especially those running servers. Imagine that you have a static IPconfigured for ens33 but then the hard disk is moved to a newer system, the NIC could be anything from ens33 to enp0s1, meaning that manual intervention is required to go and update the NIC config file (eg. /etc/network/interfa........

This is only really necessary in the case you don't want DHCP. If you are dealing with an encrypted LUKS server on the internet, you will often want to have a static IP so you know which IP to connect to (or if you have a semi-static IP assigned by DHCP). SET IP Address by /etc/initramfs-tools/initramfs.conf IP Address=192.168.1.27 Gateway=192.168.1.1 Subnet Mask: 255.255.255.0 Hostname=myhome.com IP=192.1........

Having a network bridge allows you to bridge traffic under multiple devices so they can talk natively without using any special routing, iptables/firewall or other trickery. To create your bridge you need the bridge-utils package for brctl and if you want to do things like bridge VMs that run on a tap device you will need the uml-utilities which provides "tunctl". 1.) Install the utilities to make our bridge sudo apt-get i........

If you've just installed VBox and it is not starting or working, the most common problem is usually that you don't have your kernel source installed, which means there is no kernel driver for vbox so it can't work. You may get an error that says "Kernel driver not installed" in your Virtualbox. So the first thing you should do is install your kernel source by running this: sudo apt-get install linux-headers-`uname -r`........

systemd is like the service manager for your Centos and other modern Linux distributions (including Debian/Mint/Ubuntu) allows you to enable services, stop them, restart them, check their status and even reboot your system. The key commands or arguments you will use with systemctl are the following: Unit Commands: list-units [PATTERN...] List loaded units &nbs........

You can find many ways to specify the VLANin your network configuration but Ifind this is the simplest and quickest. In this case we are talking about a bridged adapter "vmbr0" but it works even if you just had a normal non-bridged interface. The key here is that in vmbr0 you'll notice there is no IP address. We just specify "manual". Below it is a similar stanza for "vmbr0.58" in this case 58 represents the VLAN (change........

yes it does create its own json ============================================ cat /tmp/vcsaUiInstaller/ovftool-20180809-175238948-20180809-175603497.log |grep -i json 2018-08-09T17:56:04.238-07:00 verbose OVFTool[30966] [Originator@6876 sub=Default] Manifest file entry: SHA1(VMware-vCenter-Server-Appliance-6.7.0.12000-8832884_OVF10-file1.json) = 1deb658c724767697587d5909c4051c01813e6a1 --> ........

sudo apt-get install libcurl4-openssl-dev git build-essential autotools-dev autoconf libcurl3 sudo apt-get install libcurl4-gnutls-dev git clone https://github.com/wolf9466/cpuminer-multi sudo apt-get install cmake libpthread-* libmicrohttpd-dev libssl-dev libhwloc-dev git clone https://github.com/fireice-uk/xmr-stak-cpu.git make install cd bin chmod +x xmr-stak-cpu ./xmr-stak -O xmr........

#mount the VCSA DVD mount /dev/sr0 /mnt/cd #alternatively you could mount the iso directly mount -o loop vcsa.iso /your/mount/path #for this purpose we are using the CLI installer on Linux cd /mnt/cd/vcsa-cli-installer/lin64 #no it's not going to be that easy you can't just run vcsa-deploy like that you need to use a template or configured .json file ./vcsa-deploy Usage: vcsa-deploy [-h] [--version] [--supported-deploymen........

#if you have nvidia make sure you install the nvidia-cuda-toolkit so hardware acceleration can be used wget http://ffmpeg.org/releases/ffmpeg-3.3.2.tar.bz2 tar -jxvf ffmpeg-3.3.2.tar.bz2 cd ffmpeg-3.3.2/ ./configure --disable-yasm install prefix /usr/local source path ........

For themes and custom CMS setups, the typical HTML theme is not ready to go at all but here are some common sed commands (search and replace that will get most of them working without breaking as you'd expect). The problem is that often the theme directory will be separate from the content and this will break the relative paths that these themes use. sed -i s/'href="'/'href="/themes/yourtheme/'/g index.html sed -i s/'src="'/'src="/themes/y........

This is actually very simple and this example assumes your network device is "eth0" In Centos your network config would be the following: /etc/sysconfig/network-scripts/ifcfg-eth0 Take the same path and just add a "-range0" So to add a range create the following file: /etc/sysconfig/network-scripts/ifcfg-eth0-range0 IPADDR_START=192.168.1.50 IPADD........

This is basically caused by upgrading PHPto a new version like 5.4 when you had 5.2 before and an old version of Joomla. The only solution is to upgrade Joomla or downgrade PHP, both of which can be a pain. Strict Standards: Non-static method JLoader::import() should not be called statically in /home/userdir/public_html/libraries/joomla/import.php on line 29 Strict Standards: Non-static method JLoader::register() should not be ca........

Services -> Services "Static Leases" Fill out an empty line: MAC Address Host Name IP Address Those first 3 fields are mandatory, if you miss it then the changes will be lost even if you try to save. Make sure you've d........

./configure ./configure: cannot locate gcc 3.x. please install it or specify with --qemu-cc yum -y install gcc make ./configure ./configure: cannot locate gcc 3.x. please install it or specify with --qemu-cc yum -y install compat-gcc-* ./configure Error: Could not find alsa Make sure to have the alsa libs and headers installed. yum -y install alsa-lib-devel ./configure........

/scripts/phpextensionmgr install PHPSuHosin Updating md5sum list Fetching http://httpupdate.cpanel.net/cpanelsync/easy/targz.yaml (connected:0).......(request attempt 1/12)...Resolving httpupdate.cpanel.net...(resolve attempt 1/65)... Fetching http://httpupdate.cpanel.net/mirror_addr_list (connected:0).......(request attempt 1/3)......connecting to 74.50.120.123...@74.50.120.123......connected......receiving...100%......request success......Done........

If you move your hard drive(s) around to other computers/servers, you'll find that your eth0 keeps getting higher, the first time it will become eth1 and then eth2 etc and even higher if your server has dual or quad NICs. The reason is that udevd basically assigns eth0 tot he first NIC it finds and remembers it, if it encounters a NIC with a differentMAC, it assigns it one higher (eg. eth1). See the example below, I have eth2 now so how doI fix it?........

This booting error is because the Xen PV guest image uses the Xen kernel, this is not compatible with anything but a host running a Xen kernel. I did a kpartx -av virtual.img and then it created some partitions that showed up in fdisk. I mounted it and did a chroot into it and removed the xen kernel and installed a normal kernel but Xen still shows the same kernel in Grub (only the Xen one). This is strange but it seems like this Xen PV guest has some sort of hidden or........

I've thought for awhile that Asus has been banking on its years old reputation for quality amongst gamers and enthusiasts and I think I'm right. My Asus VE247H Monitor with a supposed 2MS refresh rate has 1 red/stuck/dead pixel but fortunately it can only be seen on a non-true black picture or against a blue screen. I have several Asus products and find they're all of fairly poor quality. First of all their motherboards have given me the most issues of any brand, they te........

I really am a Linux fan but my comments here may not show it. Although I'm quite familiar with Linux CLI to administer servers, I find Linux GUI OS's like Ubuntu at times very clunky. This is partially because there's no such thing as a "self-made" Linux from scratch where the UIwas designed by a single team. Linux is made up of several different projects that are generally completely separate and this lack of integratiion is a key issue that makes things f........

route add -net 192.16.5.0 netmask 255.255.255.0 eth0 Of course adjust as you need (eg. the 192.16.5.0 should be changed to the subnet you need access to and eth0 should be changed to the network device that you want that subnet routed through). I also use the /etc/sysconfig/rc.local script and add the above into it (remember that this route only gets added AFTER all other init scripts have finished though).........

Basically the two main types of distros are Debian and RHEL/Centos based. I'm just going to give a quick overview of how the configuration of IP interfaces works in Debian/Centos based distros. *Just one thing to remember, when setting IPs statically you have to manually specify a DNS server in /etc/resolv.conf (since DHCP is what normally does it automatically) Debian/Ubuntu/Kubuntu/MEPIS The IP (DHCP &........

Setup Static IP Address ONBOOTAssuming you are using eth0 Note this will work for any version of CentOS and basically any version of Redhat Linux or Redhat based distribution. You would need to create a new file [code:1:02f8d34c30] /etc/sysconfig/network-scripts/ifcfg-eth0:0[/code:1:02f8d34c30] DEVICE=eth0:0 the ":0" at the end specifies alias 0 we could actually change this to ":99" or "........